[PATCH v8 2/2] mtd: rawnand: Add Loongson-1 NAND Controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Keguang Zhang <keguang.zhang@xxxxxxxxx>

Add NAND Controller driver for Loongson-1 SoCs.

Signed-off-by: Keguang Zhang <keguang.zhang@xxxxxxxxx>
---
Changes in v8:
- Drop NAND_MONOLITHIC_READ and add support for real subpage read instead.
- Simplify the logic of ls1b_nand_parse_address() and ls1c_nand_parse_address().
- Split ls1x_nand_set_controller() into ls1x_nand_parse_instructions()
  and ls1x_nand_trigger_op().
- Implement ls1x_nand_op_cmd_mapping() to convert the opcodes instead of forcing them.
- Add ls1x_nand_check_op().
- Remove struct ls1x_nand after moving its members to struct ls1x_nfc.
- Add the prefix 'LS1X_' for all registers and their bits.
- Drop the macros: nand_readl() and nand_writel().
- Some minor fixes and improvements.

Changes in v7:
- Rename the Kconfig dependency to LOONGSON1_APB_DMA

Changes in v6:
- Amend Kconfig
- Add DT support
- Use DT data instead of platform data
- Remove MAX_ID_SIZE
- Remove case NAND_OP_CMD_INSTR in ls1x_nand_set_controller()
- Move ECC configuration to ls1x_nand_attach_chip()
- Rename variable "nand" to "ls1x"
- Rename variable "nc" to "nfc"
- Some minor fixes
- Link to v5: https://lore.kernel.org/all/20210520224213.7907-1-keguang.zhang@xxxxxxxxx

Changes in v5:
- Update the driver to fit the raw NAND framework.
- Implement exec_op() instead of legacy cmdfunc().
- Use dma_request_chan() instead of dma_request_channel().
- Some minor fixes and cleanups.

Changes in v4:
- Retrieve the controller from nand_hw_control.

Changes in v3:
- Replace __raw_readl/__raw_writel with readl/writel.
- Split ls1x_nand into two structures:
ls1x_nand_chip and ls1x_nand_controller.

Changes in v2:
- Modify the dependency in Kconfig due to the changes of DMA module.
---
 drivers/mtd/nand/raw/Kconfig          |   7 +
 drivers/mtd/nand/raw/Makefile         |   1 +
 drivers/mtd/nand/raw/loongson1_nand.c | 818 ++++++++++++++++++++++++++++++++++
 3 files changed, 826 insertions(+)

diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 614257308516..427dcf1cc826 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -448,6 +448,13 @@ config MTD_NAND_RENESAS
 	  Enables support for the NAND controller found on Renesas R-Car
 	  Gen3 and RZ/N1 SoC families.
 
+config MTD_NAND_LOONGSON1
+	tristate "Loongson1 NAND controller"
+	depends on LOONGSON1_APB_DMA || COMPILE_TEST
+	select REGMAP_MMIO
+	help
+	  Enables support for NAND controller on Loongson1 SoCs.
+
 comment "Misc"
 
 config MTD_SM_COMMON
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
index 25120a4afada..b3c65cab819c 100644
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_MTD_NAND_INTEL_LGM)	+= intel-nand-controller.o
 obj-$(CONFIG_MTD_NAND_ROCKCHIP)		+= rockchip-nand-controller.o
 obj-$(CONFIG_MTD_NAND_PL35X)		+= pl35x-nand-controller.o
 obj-$(CONFIG_MTD_NAND_RENESAS)		+= renesas-nand-controller.o
+obj-$(CONFIG_MTD_NAND_LOONGSON1)	+= loongson1_nand.o
 
 nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o
 nand-objs += nand_onfi.o
diff --git a/drivers/mtd/nand/raw/loongson1_nand.c b/drivers/mtd/nand/raw/loongson1_nand.c
new file mode 100644
index 000000000000..47e1d053b265
--- /dev/null
+++ b/drivers/mtd/nand/raw/loongson1_nand.c
@@ -0,0 +1,818 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * NAND Controller Driver for Loongson-1 SoC
+ *
+ * Copyright (C) 2015-2024 Keguang Zhang <keguang.zhang@xxxxxxxxx>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/sizes.h>
+
+/* Loongson-1 NAND Controller Registers */
+#define LS1X_NAND_CMD		0x0
+#define LS1X_NAND_ADDR1		0x4
+#define LS1X_NAND_ADDR2		0x8
+#define LS1X_NAND_TIMING	0xc
+#define LS1X_NAND_IDL		0x10
+#define LS1X_NAND_IDH_STATUS	0x14
+#define LS1X_NAND_PARAM		0x18
+#define LS1X_NAND_OP_NUM	0x1c
+
+/* NAND Command Register Bits */
+#define LS1X_NAND_CMD_OP_DONE		BIT(10)
+#define LS1X_NAND_CMD_OP_SPARE		BIT(9)
+#define LS1X_NAND_CMD_OP_MAIN		BIT(8)
+#define LS1X_NAND_CMD_STATUS		BIT(7)
+#define LS1X_NAND_CMD_RESET		BIT(6)
+#define LS1X_NAND_CMD_READID		BIT(5)
+#define LS1X_NAND_CMD_BLOCKS_ERASE	BIT(4)
+#define LS1X_NAND_CMD_ERASE		BIT(3)
+#define LS1X_NAND_CMD_WRITE		BIT(2)
+#define LS1X_NAND_CMD_READ		BIT(1)
+#define LS1X_NAND_CMD_VALID		BIT(0)
+
+#define LS1X_NAND_CMD_OP_AREA_MASK	GENMASK(9, 8)
+#define LS1X_NAND_WAIT_CYCLE_MASK	GENMASK(7, 0)
+#define LS1X_NAND_HOLD_CYCLE_MASK	GENMASK(15, 8)
+#define LS1X_NAND_CELL_SIZE_MASK	GENMASK(11, 8)
+
+#define LS1X_NAND_MAX_ADDR_CYC		5U
+#define LS1X_NAND_DMA_ADDR		0x1fe78040
+
+#define BITS_PER_WORD		(4 * BITS_PER_BYTE)
+
+struct ls1x_nfc_op {
+	char addrs[LS1X_NAND_MAX_ADDR_CYC];
+	unsigned int naddrs;
+	unsigned int addrs_offset;
+	unsigned int addr1_reg;
+	unsigned int addr2_reg;
+	unsigned int aligned_offset;
+	unsigned int row_shift;
+	unsigned int cmd_reg;
+	unsigned int rdy_timeout_ms;
+	unsigned int len;
+	size_t dma_len;
+	bool restore_row;
+	bool is_write;
+	char *buf;
+};
+
+struct ls1x_nfc_data {
+	unsigned int status_field;
+	unsigned int op_scope_field;
+	unsigned int hold_cycle;
+	unsigned int wait_cycle;
+	void (*parse_address)(struct ls1x_nfc_op *op);
+};
+
+struct ls1x_nfc {
+	struct device *dev;
+	struct nand_chip chip;
+	struct nand_controller controller;
+	const struct ls1x_nfc_data *data;
+	void __iomem *reg_base;
+	struct regmap *regmap;
+	/* DMA Engine stuff */
+	struct dma_chan *dma_chan;
+	dma_cookie_t dma_cookie;
+	struct completion dma_complete;
+};
+
+static const struct regmap_config ls1x_nand_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+};
+
+static int ls1x_nand_op_cmd_mapping(struct nand_chip *chip,
+				    struct ls1x_nfc_op *op, u8 opcode)
+{
+	struct ls1x_nfc *nfc = nand_get_controller_data(chip);
+	int ret = 0;
+
+	op->row_shift = chip->page_shift + 1;
+
+	/* The controller abstracts the following NAND operations. */
+	switch (opcode) {
+	case NAND_CMD_RESET:
+		op->cmd_reg = LS1X_NAND_CMD_RESET;
+		break;
+	case NAND_CMD_READID:
+		op->cmd_reg = LS1X_NAND_CMD_READID;
+		break;
+	case NAND_CMD_ERASE1:
+	case NAND_CMD_ERASE2:
+		op->cmd_reg = LS1X_NAND_CMD_ERASE;
+		op->addrs_offset = 2;
+		op->row_shift = chip->page_shift;
+		break;
+	case NAND_CMD_STATUS:
+		op->cmd_reg = LS1X_NAND_CMD_STATUS;
+		break;
+	case NAND_CMD_SEQIN:
+	case NAND_CMD_PAGEPROG:
+		op->cmd_reg = LS1X_NAND_CMD_WRITE;
+		op->is_write = true;
+		break;
+	case NAND_CMD_RNDOUT:
+	case NAND_CMD_RNDOUTSTART:
+		op->restore_row = true;
+		fallthrough;
+	case NAND_CMD_READ0:
+	case NAND_CMD_READSTART:
+		op->cmd_reg = LS1X_NAND_CMD_READ;
+		break;
+	default:
+		dev_err(nfc->dev, "Opcode not supported: %u\n", opcode);
+		return -EOPNOTSUPP;
+	}
+
+	return ret;
+}
+
+static int ls1x_nand_parse_instructions(struct nand_chip *chip,
+					const struct nand_subop *subop,
+					struct ls1x_nfc_op *op)
+{
+	unsigned int op_id;
+	int ret;
+
+	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
+		const struct nand_op_instr *instr = &subop->instrs[op_id];
+		unsigned int offset, naddrs;
+		const u8 *addrs;
+
+		switch (instr->type) {
+		case NAND_OP_CMD_INSTR:
+			ret = ls1x_nand_op_cmd_mapping(chip, op,
+						       instr->ctx.cmd.opcode);
+			if (ret < 0)
+				return ret;
+			break;
+		case NAND_OP_ADDR_INSTR:
+			naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
+			if (naddrs > LS1X_NAND_MAX_ADDR_CYC)
+				return -EOPNOTSUPP;
+			op->naddrs = naddrs;
+			offset = nand_subop_get_addr_start_off(subop, op_id);
+			addrs = &instr->ctx.addr.addrs[offset];
+			memcpy(op->addrs + op->addrs_offset, addrs, naddrs);
+			break;
+		case NAND_OP_DATA_IN_INSTR:
+		case NAND_OP_DATA_OUT_INSTR:
+			offset = nand_subop_get_data_start_off(subop, op_id);
+			op->len = nand_subop_get_data_len(subop, op_id);
+			if (instr->type == NAND_OP_DATA_IN_INSTR)
+				op->buf = instr->ctx.data.buf.in + offset;
+			else if (instr->type == NAND_OP_DATA_OUT_INSTR)
+				op->buf =
+				    (void *)instr->ctx.data.buf.out + offset;
+
+			break;
+		case NAND_OP_WAITRDY_INSTR:
+			op->rdy_timeout_ms = instr->ctx.waitrdy.timeout_ms;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static void ls1b_nand_parse_address(struct ls1x_nfc_op *op)
+{
+	int i;
+
+	for (i = 0; i < LS1X_NAND_MAX_ADDR_CYC; i++) {
+		if (i < 2)
+			op->addr1_reg |= (u32)op->addrs[i] << i * BITS_PER_BYTE;
+		else if (i < 4)
+			op->addr1_reg |=
+			    (u32)op->addrs[i] << (op->row_shift +
+						  (i - 2) * BITS_PER_BYTE);
+		else
+			op->addr2_reg |=
+			    (u32)op->addrs[i] >> (BITS_PER_WORD -
+						  op->row_shift - (i - 4) *
+						  BITS_PER_BYTE);
+	}
+}
+
+static void ls1c_nand_parse_address(struct ls1x_nfc_op *op)
+{
+	int i;
+
+	for (i = 0; i < LS1X_NAND_MAX_ADDR_CYC; i++) {
+		if (i < 2)
+			op->addr1_reg |= (u32)op->addrs[i] << i * BITS_PER_BYTE;
+		else
+			op->addr2_reg |=
+			    (u32)op->addrs[i] << (i - 2) * BITS_PER_BYTE;
+	}
+}
+
+static void ls1x_nand_trigger_op(struct ls1x_nfc *nfc, struct ls1x_nfc_op *op)
+{
+	struct nand_chip *chip = &nfc->chip;
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	int col0 = op->addrs[0];
+	short col;
+
+	/* restore row address for column change */
+	if (op->restore_row) {
+		op->addr2_reg = readl(nfc->reg_base + LS1X_NAND_ADDR2);
+		op->addr1_reg = readl(nfc->reg_base + LS1X_NAND_ADDR1);
+		op->addr1_reg &= ~(mtd->writesize - 1);
+	}
+
+	if (!IS_ALIGNED(col0, chip->buf_align)) {
+		col0 = ALIGN_DOWN(op->addrs[0], chip->buf_align);
+		op->aligned_offset = op->addrs[0] - col0;
+		op->addrs[0] = col0;
+	}
+
+	if (nfc->data->parse_address)
+		nfc->data->parse_address(op);
+
+	/* set address */
+	writel(op->addr1_reg, nfc->reg_base + LS1X_NAND_ADDR1);
+	writel(op->addr2_reg, nfc->reg_base + LS1X_NAND_ADDR2);
+
+	/* set data length */
+	op->dma_len = ALIGN(op->len + op->aligned_offset, chip->buf_align);
+	if (op->cmd_reg & LS1X_NAND_CMD_ERASE)
+		writel(1, nfc->reg_base + LS1X_NAND_OP_NUM);
+	else
+		writel(op->dma_len, nfc->reg_base + LS1X_NAND_OP_NUM);
+
+	/* set operation area */
+	col = op->addrs[1] << BITS_PER_BYTE | op->addrs[0];
+	if (op->len) {
+		if (col < mtd->writesize)
+			op->cmd_reg |= LS1X_NAND_CMD_OP_MAIN;
+
+		op->cmd_reg |= LS1X_NAND_CMD_OP_SPARE;
+	}
+
+	/* set operation scope */
+	if (nfc->data->op_scope_field) {
+		int op_area = op->cmd_reg & LS1X_NAND_CMD_OP_AREA_MASK;
+		unsigned int op_scope;
+
+		switch (op_area) {
+		case LS1X_NAND_CMD_OP_MAIN:
+			op_scope = mtd->writesize;
+			break;
+		case LS1X_NAND_CMD_OP_SPARE:
+			op_scope = mtd->oobsize;
+			break;
+		case LS1X_NAND_CMD_OP_AREA_MASK:
+			op_scope = mtd->writesize + mtd->oobsize;
+			break;
+		default:
+			op_scope = 0;
+			break;
+		}
+
+		op_scope <<= __ffs(nfc->data->op_scope_field);
+		regmap_update_bits(nfc->regmap, LS1X_NAND_PARAM,
+				   nfc->data->op_scope_field, op_scope);
+	}
+
+	/* set command */
+	writel(op->cmd_reg, nfc->reg_base + LS1X_NAND_CMD);
+
+	/* trigger operation */
+	regmap_write_bits(nfc->regmap, LS1X_NAND_CMD,
+			  LS1X_NAND_CMD_VALID, LS1X_NAND_CMD_VALID);
+}
+
+static int ls1x_nand_wait_for_op_done(struct ls1x_nfc *nfc,
+				      struct ls1x_nfc_op *op)
+{
+	unsigned int val;
+	int ret = 0;
+
+	if (op->rdy_timeout_ms) {
+		ret = regmap_read_poll_timeout(nfc->regmap, LS1X_NAND_CMD,
+					       val, val & LS1X_NAND_CMD_OP_DONE,
+					       0, op->rdy_timeout_ms * 1000);
+		if (ret)
+			dev_err(nfc->dev, "operation failed\n");
+	}
+
+	return ret;
+}
+
+static void ls1x_nand_dma_callback(void *data)
+{
+	struct ls1x_nfc *nfc = (struct ls1x_nfc *)data;
+	struct dma_chan *chan = nfc->dma_chan;
+	struct device *dev = chan->device->dev;
+	enum dma_status status;
+
+	status = dmaengine_tx_status(chan, nfc->dma_cookie, NULL);
+	if (likely(status == DMA_COMPLETE))
+		dev_dbg(dev, "DMA complete with cookie=%d\n", nfc->dma_cookie);
+	else
+		dev_err(dev, "DMA error with cookie=%d\n", nfc->dma_cookie);
+
+	complete(&nfc->dma_complete);
+}
+
+static int ls1x_nand_dma_transfer(struct ls1x_nfc *nfc,
+				  struct ls1x_nfc_op *op)
+{
+	struct nand_chip *chip = &nfc->chip;
+	struct dma_chan *chan = nfc->dma_chan;
+	struct device *dev = chan->device->dev;
+	struct dma_async_tx_descriptor *desc;
+	enum dma_data_direction data_dir =
+	    op->is_write ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+	enum dma_transfer_direction xfer_dir =
+	    op->is_write ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
+	char *dma_buf = NULL;
+	dma_addr_t dma_addr;
+	int ret;
+
+	if (IS_ALIGNED((u32)op->buf, chip->buf_align) &&
+	    IS_ALIGNED(op->len, chip->buf_align)) {
+		dma_addr = dma_map_single(dev, op->buf, op->len, data_dir);
+		if (dma_mapping_error(dev, dma_addr)) {
+			dev_err(dev, "failed to map DMA buffer\n");
+			return -ENXIO;
+		}
+	} else if (!op->is_write) {
+		dma_buf = dma_alloc_coherent(dev, op->dma_len, &dma_addr,
+					     GFP_KERNEL);
+		if (!dma_buf)
+			return -ENOMEM;
+	} else {
+		dev_err(dev, "subpage writing not supported\n");
+		return -EOPNOTSUPP;
+	}
+
+	desc = dmaengine_prep_slave_single(chan, dma_addr, op->dma_len,
+					   xfer_dir, DMA_PREP_INTERRUPT);
+	if (!desc) {
+		dev_err(dev, "failed to prepare DMA descriptor\n");
+		ret = PTR_ERR(desc);
+		goto err;
+	}
+	desc->callback = ls1x_nand_dma_callback;
+	desc->callback_param = nfc;
+
+	nfc->dma_cookie = dmaengine_submit(desc);
+	ret = dma_submit_error(nfc->dma_cookie);
+	if (ret) {
+		dev_err(dev, "failed to submit DMA descriptor\n");
+		goto err;
+	}
+
+	dev_dbg(dev, "issue DMA with cookie=%d\n", nfc->dma_cookie);
+	dma_async_issue_pending(chan);
+
+	ret = wait_for_completion_timeout(&nfc->dma_complete,
+					  msecs_to_jiffies(2000));
+	if (!ret) {
+		dmaengine_terminate_sync(chan);
+		reinit_completion(&nfc->dma_complete);
+		ret = -ETIMEDOUT;
+		goto err;
+	}
+	ret = 0;
+
+	if (dma_buf)
+		memcpy(op->buf, dma_buf + op->aligned_offset, op->len);
+err:
+	if (dma_buf)
+		dma_free_coherent(dev, op->dma_len, dma_buf, dma_addr);
+	else
+		dma_unmap_single(dev, dma_addr, op->len, data_dir);
+
+	return ret;
+}
+
+static int ls1x_nand_misc_type_exec(struct nand_chip *chip,
+				    const struct nand_subop *subop,
+				    struct ls1x_nfc_op *op)
+{
+	struct ls1x_nfc *nfc = nand_get_controller_data(chip);
+	int ret;
+
+	ret = ls1x_nand_parse_instructions(chip, subop, op);
+	if (ret)
+		return ret;
+
+	ls1x_nand_trigger_op(nfc, op);
+
+	return ls1x_nand_wait_for_op_done(nfc, op);
+}
+
+static int ls1x_nand_read_id_type_exec(struct nand_chip *chip,
+				       const struct nand_subop *subop)
+{
+	struct ls1x_nfc *nfc = nand_get_controller_data(chip);
+	struct ls1x_nfc_op op = { };
+	int i, ret;
+	union {
+		char ids[5];
+		struct {
+			int idl;
+			char idh;
+		};
+	} nand_id;
+
+	ret = ls1x_nand_misc_type_exec(chip, subop, &op);
+	if (ret) {
+		dev_err(nfc->dev, "failed to read id! %d\n", ret);
+		return ret;
+	}
+
+	nand_id.idl = readl(nfc->reg_base + LS1X_NAND_IDL);
+	nand_id.idh = readb(nfc->reg_base + LS1X_NAND_IDH_STATUS);
+
+	for (i = 0; i < min(sizeof(nand_id.ids), op.len); i++)
+		op.buf[i] = nand_id.ids[sizeof(nand_id.ids) - 1 - i];
+
+	return ret;
+}
+
+static int ls1x_nand_read_status_type_exec(struct nand_chip *chip,
+					   const struct nand_subop *subop)
+{
+	struct ls1x_nfc *nfc = nand_get_controller_data(chip);
+	struct ls1x_nfc_op op = { };
+	int val, ret;
+
+	ret = ls1x_nand_misc_type_exec(chip, subop, &op);
+	if (ret) {
+		dev_err(nfc->dev, "failed to read status! %d\n", ret);
+		return ret;
+	}
+
+	val = readl(nfc->reg_base +
+		    LS1X_NAND_IDH_STATUS) & ~nfc->data->status_field;
+	op.buf[0] = val << ffs(nfc->data->status_field);
+
+	return ret;
+}
+
+static int ls1x_nand_zerolen_type_exec(struct nand_chip *chip,
+				       const struct nand_subop *subop)
+{
+	struct ls1x_nfc_op op = { };
+
+	return ls1x_nand_misc_type_exec(chip, subop, &op);
+}
+
+static int ls1x_nand_data_type_exec(struct nand_chip *chip,
+				    const struct nand_subop *subop)
+{
+	struct ls1x_nfc *nfc = nand_get_controller_data(chip);
+	struct ls1x_nfc_op op = { };
+	int ret;
+
+	ret = ls1x_nand_parse_instructions(chip, subop, &op);
+	if (ret)
+		return ret;
+
+	ls1x_nand_trigger_op(nfc, &op);
+
+	ret = ls1x_nand_dma_transfer(nfc, &op);
+	if (ret)
+		return ret;
+
+	return ls1x_nand_wait_for_op_done(nfc, &op);
+}
+
+static const struct nand_op_parser ls1x_nand_op_parser = NAND_OP_PARSER(
+	NAND_OP_PARSER_PATTERN(
+		ls1x_nand_read_id_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, LS1X_NAND_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 8)),
+	NAND_OP_PARSER_PATTERN(
+		ls1x_nand_read_status_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 1)),
+	NAND_OP_PARSER_PATTERN(
+		ls1x_nand_zerolen_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+	NAND_OP_PARSER_PATTERN(
+		ls1x_nand_zerolen_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, LS1X_NAND_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
+	NAND_OP_PARSER_PATTERN(
+		ls1x_nand_data_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, LS1X_NAND_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 0)),
+	NAND_OP_PARSER_PATTERN(
+		ls1x_nand_data_type_exec,
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(false, LS1X_NAND_MAX_ADDR_CYC),
+		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, 0),
+		NAND_OP_PARSER_PAT_CMD_ELEM(false),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
+	);
+
+static int ls1x_nand_check_op(struct nand_chip *chip,
+			      const struct nand_operation *op)
+{
+	const struct nand_op_instr *instr;
+	int op_id;
+
+	for (op_id = 0; op_id < op->ninstrs; op_id++) {
+		instr = &op->instrs[op_id];
+
+		switch (instr->type) {
+		case NAND_OP_CMD_INSTR:
+			if (instr->ctx.cmd.opcode != NAND_CMD_RESET &&
+			    instr->ctx.cmd.opcode != NAND_CMD_READID &&
+			    instr->ctx.cmd.opcode != NAND_CMD_ERASE1 &&
+			    instr->ctx.cmd.opcode != NAND_CMD_ERASE2 &&
+			    instr->ctx.cmd.opcode != NAND_CMD_STATUS &&
+			    instr->ctx.cmd.opcode != NAND_CMD_SEQIN &&
+			    instr->ctx.cmd.opcode != NAND_CMD_PAGEPROG &&
+			    instr->ctx.cmd.opcode != NAND_CMD_RNDOUT &&
+			    instr->ctx.cmd.opcode != NAND_CMD_RNDOUTSTART &&
+			    instr->ctx.cmd.opcode != NAND_CMD_READ0 &&
+			    instr->ctx.cmd.opcode != NAND_CMD_READSTART)
+				return -EOPNOTSUPP;
+			break;
+		case NAND_OP_ADDR_INSTR:
+			if (instr->ctx.addr.naddrs > LS1X_NAND_MAX_ADDR_CYC)
+				return -EOPNOTSUPP;
+			break;
+		default:
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int ls1x_nand_exec_op(struct nand_chip *chip,
+			     const struct nand_operation *op, bool check_only)
+{
+	if (check_only)
+		return ls1x_nand_check_op(chip, op);
+
+	return nand_op_parser_exec_op(chip, &ls1x_nand_op_parser, op,
+				      check_only);
+}
+
+static int ls1x_nand_attach_chip(struct nand_chip *chip)
+{
+	struct ls1x_nfc *nfc = nand_get_controller_data(chip);
+	u64 chipsize = nanddev_target_size(&chip->base);
+	int cell_size = 0;
+
+	switch (chipsize) {
+	case SZ_128M:
+		cell_size = 0x0;
+		break;
+	case SZ_256M:
+		cell_size = 0x1;
+		break;
+	case SZ_512M:
+		cell_size = 0x2;
+		break;
+	case SZ_1G:
+		cell_size = 0x3;
+		break;
+	case SZ_2G:
+		cell_size = 0x4;
+		break;
+	case SZ_4G:
+		cell_size = 0x5;
+		break;
+	case SZ_8G:
+		cell_size = 0x6;
+		break;
+	case SZ_16G:
+		cell_size = 0x7;
+		break;
+	default:
+		dev_err(nfc->dev, "unsupported chip size: %llu MB\n", chipsize);
+		return -EOPNOTSUPP;
+	}
+
+	/* set cell size */
+	regmap_update_bits(nfc->regmap, LS1X_NAND_PARAM,
+			   LS1X_NAND_CELL_SIZE_MASK,
+			   FIELD_PREP(LS1X_NAND_CELL_SIZE_MASK, cell_size));
+
+	regmap_update_bits(nfc->regmap, LS1X_NAND_TIMING,
+			   LS1X_NAND_HOLD_CYCLE_MASK,
+			   FIELD_PREP(LS1X_NAND_HOLD_CYCLE_MASK,
+				      nfc->data->hold_cycle));
+	regmap_update_bits(nfc->regmap, LS1X_NAND_TIMING,
+			   LS1X_NAND_WAIT_CYCLE_MASK,
+			   FIELD_PREP(LS1X_NAND_WAIT_CYCLE_MASK,
+				      nfc->data->wait_cycle));
+
+	chip->ecc.read_page_raw = nand_monolithic_read_page_raw;
+	chip->ecc.write_page_raw = nand_monolithic_write_page_raw;
+
+	return 0;
+}
+
+static const struct nand_controller_ops ls1x_nfc_ops = {
+	.exec_op = ls1x_nand_exec_op,
+	.attach_chip = ls1x_nand_attach_chip,
+};
+
+static void ls1x_nand_controller_cleanup(struct ls1x_nfc *nfc)
+{
+	if (nfc->dma_chan)
+		dma_release_channel(nfc->dma_chan);
+}
+
+static int ls1x_nand_controller_init(struct ls1x_nfc *nfc)
+{
+	struct device *dev = nfc->dev;
+	struct dma_chan *chan;
+	struct dma_slave_config cfg = { };
+	int ret;
+
+	nfc->regmap = devm_regmap_init_mmio(dev, nfc->reg_base,
+					    &ls1x_nand_regmap_config);
+	if (IS_ERR(nfc->regmap))
+		return dev_err_probe(dev, PTR_ERR(nfc->regmap),
+				     "failed to init regmap\n");
+
+	chan = dma_request_chan(dev, "rxtx");
+	if (IS_ERR(chan))
+		return dev_err_probe(dev, PTR_ERR(chan),
+				     "failed to request DMA channel\n");
+	nfc->dma_chan = chan;
+
+	cfg.src_addr = LS1X_NAND_DMA_ADDR;
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	cfg.dst_addr = LS1X_NAND_DMA_ADDR;
+	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	ret = dmaengine_slave_config(nfc->dma_chan, &cfg);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "failed to config DMA channel\n");
+
+	init_completion(&nfc->dma_complete);
+
+	dev_dbg(dev, "got %s for %s access\n",
+		dma_chan_name(nfc->dma_chan), dev_name(dev));
+
+	return 0;
+}
+
+static int ls1x_nand_chip_init(struct ls1x_nfc *nfc)
+{
+	struct device *dev = nfc->dev;
+	int nchips = of_get_child_count(dev->of_node);
+	struct device_node *chip_np;
+	struct nand_chip *chip = &nfc->chip;
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	int ret = 0;
+
+	if (nchips != 1)
+		return dev_err_probe(dev, -EINVAL,
+				     "Currently one NAND chip supported\n");
+
+	chip_np = of_get_next_child(dev->of_node, NULL);
+	if (!chip_np)
+		return dev_err_probe(dev, -ENODEV,
+				     "failed to get child node for NAND chip\n");
+
+	chip->controller = &nfc->controller;
+	chip->options = NAND_NO_SUBPAGE_WRITE | NAND_USES_DMA | NAND_BROKEN_XD;
+	chip->buf_align = 16;
+	nand_set_controller_data(chip, nfc);
+	nand_set_flash_node(chip, chip_np);
+
+	mtd->dev.parent = dev;
+	mtd->name = "ls1x-nand";
+	mtd->owner = THIS_MODULE;
+
+	ret = nand_scan(chip, 1);
+	if (ret) {
+		of_node_put(chip_np);
+		return ret;
+	}
+
+	ret = mtd_device_register(mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "failed to register MTD device! %d\n", ret);
+		nand_cleanup(chip);
+		of_node_put(chip_np);
+	}
+
+	return ret;
+}
+
+static int ls1x_nand_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct ls1x_nfc_data *data;
+	struct ls1x_nfc *nfc;
+	int ret;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return -ENODEV;
+
+	nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
+	if (!nfc)
+		return -ENOMEM;
+
+	nfc->reg_base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(nfc->reg_base))
+		return PTR_ERR(nfc->reg_base);
+
+	nand_controller_init(&nfc->controller);
+
+	nfc->dev = dev;
+	nfc->data = data;
+	nfc->controller.ops = &ls1x_nfc_ops;
+
+	ret = ls1x_nand_controller_init(nfc);
+	if (ret)
+		goto err;
+
+	ret = ls1x_nand_chip_init(nfc);
+	if (ret)
+		goto err;
+
+	platform_set_drvdata(pdev, nfc);
+
+	return 0;
+err:
+	ls1x_nand_controller_cleanup(nfc);
+
+	return ret;
+}
+
+static void ls1x_nand_remove(struct platform_device *pdev)
+{
+	struct ls1x_nfc *nfc = platform_get_drvdata(pdev);
+	struct nand_chip *chip = &nfc->chip;
+	int ret;
+
+	ret = mtd_device_unregister(nand_to_mtd(chip));
+	WARN_ON(ret);
+	nand_cleanup(chip);
+	ls1x_nand_controller_cleanup(nfc);
+}
+
+static const struct ls1x_nfc_data ls1b_nfc_data = {
+	.status_field = GENMASK(15, 8),
+	.hold_cycle = 0x2,
+	.wait_cycle = 0xc,
+	.parse_address = ls1b_nand_parse_address,
+};
+
+static const struct ls1x_nfc_data ls1c_nfc_data = {
+	.status_field = GENMASK(23, 16),
+	.op_scope_field = GENMASK(29, 16),
+	.hold_cycle = 0x2,
+	.wait_cycle = 0xc,
+	.parse_address = ls1c_nand_parse_address,
+};
+
+static const struct of_device_id ls1x_nfc_match[] = {
+	{ .compatible = "loongson,ls1b-nfc", .data = &ls1b_nfc_data },
+	{ .compatible = "loongson,ls1c-nfc", .data = &ls1c_nfc_data },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ls1x_nfc_match);
+
+static struct platform_driver ls1x_nand_driver = {
+	.probe = ls1x_nand_probe,
+	.remove = ls1x_nand_remove,
+	.driver = {
+		.name = KBUILD_MODNAME,
+		.of_match_table = ls1x_nfc_match,
+	},
+};
+
+module_platform_driver(ls1x_nand_driver);
+
+MODULE_AUTHOR("Keguang Zhang <keguang.zhang@xxxxxxxxx>");
+MODULE_DESCRIPTION("Loongson-1 NAND Controller driver");
+MODULE_LICENSE("GPL");

-- 
2.43.0






[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux