[PATCH 3/3] V4L2: Add a v4l2-subdev (soc-camera) driver for OmniVision OV2640 sensor

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Signed-off-by: Alberto Panizzo <maramaopercheseimorto@xxxxxxxxx>
---
 drivers/media/video/Kconfig     |    6 +
 drivers/media/video/Makefile    |    1 +
 drivers/media/video/ov2640.c    | 1153
+++++++++++++++++++++++++++++++++++++++
 include/media/v4l2-chip-ident.h |    1 +
 4 files changed, 1161 insertions(+), 0 deletions(-)
 create mode 100644 drivers/media/video/ov2640.c

diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
index 0efbb29..898f76f 100644
--- a/drivers/media/video/Kconfig
+++ b/drivers/media/video/Kconfig
@@ -807,6 +807,12 @@ config SOC_CAMERA_OV9640
 	help
 	  This is a ov9640 camera driver
 
+config SOC_CAMERA_OV2640
+	tristate "ov2640 camera support"
+	depends on SOC_CAMERA && I2C
+	help
+	  This is a ov2640 camera driver
+
 config MX1_VIDEO
 	bool
 
diff --git a/drivers/media/video/Makefile b/drivers/media/video/Makefile
index af79d47..fac185d 100644
--- a/drivers/media/video/Makefile
+++ b/drivers/media/video/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_SOC_CAMERA_MT9V022)	+= mt9v022.o
 obj-$(CONFIG_SOC_CAMERA_OV6650)		+= ov6650.o
 obj-$(CONFIG_SOC_CAMERA_OV772X)		+= ov772x.o
 obj-$(CONFIG_SOC_CAMERA_OV9640)		+= ov9640.o
+obj-$(CONFIG_SOC_CAMERA_OV2640)		+= ov2640.o
 obj-$(CONFIG_SOC_CAMERA_RJ54N1)		+= rj54n1cb0c.o
 obj-$(CONFIG_SOC_CAMERA_TW9910)		+= tw9910.o
 
diff --git a/drivers/media/video/ov2640.c b/drivers/media/video/ov2640.c
new file mode 100644
index 0000000..5edf23e
--- /dev/null
+++ b/drivers/media/video/ov2640.c
@@ -0,0 +1,1153 @@
+/*
+ * ov2640 Camera Driver
+ *
+ * Copyright (C) 2010 Alberto Panizzo <maramaopercheseimorto@xxxxxxxxx>
+ *
+ * Based on ov772x, ov9640 drivers and previous non merged
implementations.
+ *
+ * Copyright 2005-2009 Freescale Semiconductor, Inc. All Rights
Reserved.
+ * Copyright (C) 2006, OmniVision
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-chip-ident.h>
+#include <media/v4l2-subdev.h>
+#include <media/soc_camera.h>
+#include <media/soc_mediabus.h>
+
+#define VAL_SET(x, mask, rshift, lshift)  \
+		((((x) >> rshift) & mask) << lshift)
+/*
+ * DSP registers
+ * register offset for BANK_SEL == BANK_SEL_DSP
+ */
+#define R_BYPASS    0x05 /* Bypass DSP */
+#define   R_BYPASS_DSP_BYPAS    0x01 /* Bypass DSP. sensor out directly
*/
+#define   R_BYPASS_USE_DSP      0x00 /* Bypass DSP. sensor out directly
*/
+#define QS          0x44 /* Quantization Scale Factor */
+#define CTRLI       0x50
+#define   CTRLI_LP_DP           0x80
+#define   CTRLI_ROUND           0x40
+#define   CTRLI_V_DIV_SET(x)    VAL_SET(x, 0x3, 0, 3)
+#define   CTRLI_H_DIV_SET(x)    VAL_SET(x, 0x3, 0, 0)
+#define HSIZE       0x51 /* H_SIZE[7:0] (real/4) */
+#define   HSIZE_SET(x)          VAL_SET(x, 0xFF, 2, 0)
+#define VSIZE       0x52 /* V_SIZE[7:0] (real/4) */
+#define   VSIZE_SET(x)          VAL_SET(x, 0xFF, 2, 0)
+#define XOFFL       0x53 /* OFFSET_X[7:0] */
+#define   XOFFL_SET(x)          VAL_SET(x, 0xFF, 0, 0)
+#define YOFFL       0x54 /* OFFSET_Y[7:0] */
+#define   YOFFL_SET(x)          VAL_SET(x, 0xFF, 0, 0)
+#define VHYX        0x55 /* Offset and size completion */
+#define   VHYX_VSIZE_SET(x)     VAL_SET(x, 0x1, (8+2), 7)
+#define   VHYX_HSIZE_SET(x)     VAL_SET(x, 0x1, (8+2), 3)
+#define   VHYX_YOFF_SET(x)      VAL_SET(x, 0x3, 8, 4)
+#define   VHYX_XOFF_SET(x)      VAL_SET(x, 0x3, 8, 0)
+#define DPRP        0x56
+#define TEST        0x57 /* Horizontal size completion */
+#define   TEST_HSIZE_SET(x)     VAL_SET(x, 0x1, (9+2), 7)
+#define ZMOW        0x5A /* Zoom: Out Width  OUTW[7:0] (real/4) */
+#define   ZMOW_OUTW_SET(x)      VAL_SET(x, 0xFF, 2, 0)
+#define ZMOH        0x5B /* Zoom: Out Height OUTH[7:0] (real/4) */
+#define   ZMOH_OUTH_SET(x)      VAL_SET(x, 0xFF, 2, 0)
+#define ZMHH        0x5C /* Zoom: Speed and H&W completion */
+#define   ZMHH_ZSPEED_SET(x)    VAL_SET(x, 0x0F, 0, 4)
+#define   ZMHH_OUTH_SET(x)      VAL_SET(x, 0x1, (8+2), 2)
+#define   ZMHH_OUTW_SET(x)      VAL_SET(x, 0x3, (8+2), 0)
+#define BPADDR      0x7C /* SDE Indirect Register Access: Address */
+#define BPDATA      0x7D /* SDE Indirect Register Access: Data */
+#define CTRL2       0x86 /* DSP Module enable 2 */
+#define   CTRL2_DCW_EN          0x20
+#define   CTRL2_SDE_EN          0x10
+#define   CTRL2_UV_ADJ_EN       0x08
+#define   CTRL2_UV_AVG_EN       0x04
+#define   CTRL2_CMX_EN          0x01
+#define CTRL3       0x87 /* DSP Module enable 3 */
+#define   CTRL3_BPC_EN          0x80
+#define   CTRL3_WPC_EN          0x40
+#define SIZEL       0x8C /* Image Size Completion */
+#define   SIZEL_HSIZE8_11_SET(x) VAL_SET(x, 0x1, 11, 6)
+#define   SIZEL_HSIZE8_SET(x)    VAL_SET(x, 0x7, 0, 3)
+#define   SIZEL_VSIZE8_SET(x)    VAL_SET(x, 0x7, 0, 0)
+#define HSIZE8      0xC0 /* Image Horizontal Size HSIZE[10:3] */
+#define   HSIZE8_SET(x)         VAL_SET(x, 0xFF, 3, 0)
+#define VSIZE8      0xC1 /* Image Vertical Size VSIZE[10:3] */
+#define   VSIZE8_SET(x)         VAL_SET(x, 0xFF, 3, 0)
+#define CTRL0       0xC2 /* DSP Module enable 0 */
+#define   CTRL0_AEC_EN       0x80
+#define   CTRL0_AEC_SEL      0x40
+#define   CTRL0_STAT_SEL     0x20
+#define   CTRL0_VFIRST       0x10
+#define   CTRL0_YUV422       0x08
+#define   CTRL0_YUV_EN       0x04
+#define   CTRL0_RGB_EN       0x02
+#define   CTRL0_RAW_EN       0x01
+#define CTRL1       0xC3 /* DSP Module enable 1 */
+#define   CTRL1_CIP          0x80
+#define   CTRL1_DMY          0x40
+#define   CTRL1_RAW_GMA      0x20
+#define   CTRL1_DG           0x10
+#define   CTRL1_AWB          0x08
+#define   CTRL1_AWB_GAIN     0x04
+#define   CTRL1_LENC         0x02
+#define   CTRL1_PRE          0x01
+#define R_DVP_SP    0xD3 /* DVP output speed control */
+#define   R_DVP_SP_AUTO_MODE 0x80
+#define   R_DVP_SP_DVP_MASK  0x3F /* DVP PCLK = sysclk (48)/[6:0]
(YUV0);
+				   *          = sysclk (48)/(2*[6:0]) (RAW);*/
+#define IMAGE_MODE  0xDA /* Image Output Format Select */
+#define   IMAGE_MODE_Y8_DVP_EN   0x40
+#define   IMAGE_MODE_JPEG_EN     0x10
+#define   IMAGE_MODE_YUV422      0x00
+#define   IMAGE_MODE_RAW10       0x04 /* (DVP) */
+#define   IMAGE_MODE_RGB565      0x08
+#define   IMAGE_MODE_HREF_VSYNC  0x02 /* HREF timing select in DVP JPEG
output
+				       * mode (0 for HREF is same as sensor) */
+#define   IMAGE_MODE_LBYTE_FIRST 0x01 /* Byte swap enable for DVP
+				       *    1: Low byte first UYVY (C2[4] =0)
+				       *        VYUY (C2[4] =1)
+				       *    0: High byte first YUYV (C2[4]=0)
+				       *        YVYU (C2[4] = 1) */
+#define RESET       0xE0 /* Reset */
+#define   RESET_MICROC       0x40
+#define   RESET_SCCB         0x20
+#define   RESET_JPEG         0x10
+#define   RESET_DVP          0x04
+#define   RESET_IPU          0x02
+#define   RESET_CIF          0x01
+#define REGED       0xED /* Register ED */
+#define   REGED_CLK_OUT_DIS  0x10
+#define MS_SP       0xF0 /* SCCB Master Speed */
+#define SS_ID       0xF7 /* SCCB Slave ID */
+#define SS_CTRL     0xF8 /* SCCB Slave Control */
+#define   SS_CTRL_ADD_AUTO_INC  0x20
+#define   SS_CTRL_EN            0x08
+#define   SS_CTRL_DELAY_CLK     0x04
+#define   SS_CTRL_ACC_EN        0x02
+#define   SS_CTRL_SEN_PASS_THR  0x01
+#define MC_BIST     0xF9 /* Microcontroller misc register */
+#define   MC_BIST_RESET           0x80 /* Microcontroller Reset */
+#define   MC_BIST_BOOT_ROM_SEL    0x40
+#define   MC_BIST_12KB_SEL        0x20
+#define   MC_BIST_12KB_MASK       0x30
+#define   MC_BIST_512KB_SEL       0x08
+#define   MC_BIST_512KB_MASK      0x0C
+#define   MC_BIST_BUSY_BIT_R      0x02
+#define   MC_BIST_MC_RES_ONE_SH_W 0x02
+#define   MC_BIST_LAUNCH          0x01
+#define BANK_SEL    0xFF /* Register Bank Select */
+#define   BANK_SEL_DSP     0x00
+#define   BANK_SEL_SENS    0x01
+
+/*
+ * Sensor registers
+ * register offset for BANK_SEL == BANK_SEL_SENS
+ */
+#define GAIN        0x00 /* AGC - Gain control gain setting */
+#define COM1        0x03 /* Common control 1 */
+#define   COM1_1_DUMMY_FR          0x40
+#define   COM1_3_DUMMY_FR          0x80
+#define   COM1_7_DUMMY_FR          0xC0
+#define   COM1_VWIN_LSB_UXGA       0x0F
+#define   COM1_VWIN_LSB_SVGA       0x0A
+#define   COM1_VWIN_LSB_CIF        0x06
+#define REG04       0x04 /* Register 04 */
+#define   REG04_DEF             0x20	/* Always set */
+#define   REG04_HFLIP_IMG       0x80	/* Horizontal mirror image ON/OFF
*/
+#define   REG04_VFLIP_IMG       0x40	/* Vertical flip image ON/OFF */
+#define   REG04_VREF_EN         0x10
+#define   REG04_HREF_EN         0x08
+#define   REG04_AEC_SET(x)      VAL_SET(x, 0x3, 0, 0)
+#define REG08       0x08 /* Frame Exposure One-pin Control Pre-charge
Row Num */
+#define COM2        0x09 /* Common control 2 */
+#define   COM2_SOFT_SLEEP_MODE  0x10	/* Soft sleep mode */
+					/* Output drive capability */
+#define   COM2_OCAP_Nx_SET(N)   (((N) - 1) & 0x03) /* N = [1x .. 4x] */
+#define PID         0x0A /* Product ID Number MSB */
+#define VER         0x0B /* Product ID Number LSB */
+#define COM3        0x0C /* Common control 3 */
+#define   COM3_BAND_50H        0x04 /* 0 For Banding at 60H */
+#define   COM3_BAND_AUTO       0x02 /* Auto Banding */
+#define   COM3_SING_FR_SNAPSH  0x01 /* 0 For enable live video output
after the
+				     * snapshot sequence*/
+#define AEC         0x10 /* AEC[9:2] Exposure Value */
+#define CLKRC       0x11 /* Internal clock */
+#define   CLKRC_EN             0x80
+#define   CLKRC_DIV_SET(x)     (((x) - 1) & 0x1F) /* CLK = XVCLK/(x) */
+#define COM7        0x12 /* Common control 7 */
+#define   COM7_SRST            0x80 /* Initiates system reset. All
registers are
+				     * set to factory default values after which
+				     * the chip resumes normal operation */
+#define   COM7_RES_UXGA        0x00 /* Resolution selectors for UXGA */
+#define   COM7_RES_SVGA        0x40 /* SVGA */
+#define   COM7_RES_CIF         0x20 /* CIF */
+#define   COM7_ZOOM_EN         0x04 /* Enable Zoom mode */
+#define   COM7_COLOR_BAR_TEST  0x02 /* Enable Color Bar Test Pattern */
+#define COM8        0x13 /* Common control 8 */
+#define   COM8_DEF             0xC0 /* Banding filter ON/OFF */
+#define   COM8_BNDF_EN         0x20 /* Banding filter ON/OFF */
+#define   COM8_AGC_EN          0x04 /* AGC Auto/Manual control
selection */
+#define   COM8_AEC_EN          0x01 /* Auto/Manual Exposure control */
+#define COM9        0x14 /* Common control 9
+			  * Automatic gain ceiling - maximum AGC value [7:5]*/
+#define   COM9_AGC_GAIN_2x     0x00	/* 000 :   2x */
+#define   COM9_AGC_GAIN_4x     0x20	/* 001 :   4x */
+#define   COM9_AGC_GAIN_8x     0x40	/* 010 :   8x */
+#define   COM9_AGC_GAIN_16x    0x60	/* 011 :  16x */
+#define   COM9_AGC_GAIN_32x    0x80	/* 100 :  32x */
+#define   COM9_AGC_GAIN_64x    0xA0	/* 101 :  64x */
+#define   COM9_AGC_GAIN_128x   0xC0	/* 110 : 128x */
+#define COM10       0x15 /* Common control 10 */
+#define   COM10_PCLK_HREF      0x20 /* PCLK output qualified by HREF */
+#define   COM10_PCLK_RISE      0x10 /* Data is updated at the rising
edge of
+				     * PCLK (user can latch data at the next
+				     * falling edge of PCLK).
+				     * 0 otherwise. */
+#define   COM10_HREF_INV       0x08 /* Invert HREF polarity:
+				     * HREF negative for valid data*/
+#define   COM10_VSINC_INV      0x02 /* Invert VSYNC polarity */
+#define HSTART      0x17 /* Horizontal Window start MSB 8 bit */
+#define HEND        0x18 /* Horizontal Window end MSB 8 bit */
+#define VSTART      0x19 /* Vertical Window start MSB 8 bit */
+#define VEND        0x1A /* Vertical Window end MSB 8 bit */
+#define MIDH        0x1C /* Manufacturer ID byte - high */
+#define MIDL        0x1D /* Manufacturer ID byte - low  */
+#define AEW         0x24 /* AGC/AEC - Stable operating region (upper
limit) */
+#define AEB         0x25 /* AGC/AEC - Stable operating region (lower
limit) */
+#define VV          0x26 /* AGC/AEC Fast mode operating region */
+#define   VV_HIGH_TH_SET(x)      VAL_SET(x, 0xF, 0, 4)
+#define   VV_LOW_TH_SET(x)       VAL_SET(x, 0xF, 0, 0)
+#define REG2A       0x2A /* Dummy pixel insert MSB */
+#define FRARL       0x2B /* Dummy pixel insert LSB */
+#define ADDVFL      0x2D /* LSB of insert dummy lines in Vertical
direction */
+#define ADDVFH      0x2E /* MSB of insert dummy lines in Vertical
direction */
+#define YAVG        0x2F /* Y/G Channel Average value */
+#define REG32       0x32 /* Common Control 32 */
+#define   REG32_PCLK_DIV_2    0x80 /* PCLK freq divided by 2 */
+#define   REG32_PCLK_DIV_4    0xC0 /* PCLK freq divided by 4 */
+#define ARCOM2      0x34 /* Zoom: Horizontal start point */
+#define REG45       0x45 /* Register 45 */
+#define FLL         0x46 /* Frame Length Adjustment LSBs */
+#define FLH         0x47 /* Frame Length Adjustment MSBs */
+#define COM19       0x48 /* Zoom: Vertical start point */
+#define ZOOMS       0x49 /* Zoom: Vertical start point */
+#define COM22       0x4B /* Flash light control */
+#define COM25       0x4E /* For Banding operations */
+#define BD50        0x4F /* 50Hz Banding AEC 8 LSBs */
+#define BD60        0x50 /* 60Hz Banding AEC 8 LSBs */
+#define REG5D       0x5D /* AVGsel[7:0],   16-zone average weight
option */
+#define REG5E       0x5E /* AVGsel[15:8],  16-zone average weight
option */
+#define REG5F       0x5F /* AVGsel[23:16], 16-zone average weight
option */
+#define REG60       0x60 /* AVGsel[31:24], 16-zone average weight
option */
+#define HISTO_LOW   0x61 /* Histogram Algorithm Low Level */
+#define HISTO_HIGH  0x62 /* Histogram Algorithm High Level */
+
+/*
+ * ID
+ */
+#define MANUFACTURER_ID  0x7FA2
+#define PID_OV2640       0x2642
+#define VERSION(pid, ver) ((pid<<8)|(ver&0xFF))
+
+/*
+ * struct
+ */
+struct regval_list {
+	u8 reg_num;
+	u16 value;
+};
+
+/* supported resolutions */
+enum ov2640_width_sizes {
+	W_QCIF	= 176,
+	W_QVGA	= 320,
+	W_CIF	= 352,
+	W_VGA	= 640,
+	W_SVGA	= 800,
+	W_XGA	= 1024,
+	W_SXGA	= 1280,
+	W_UXGA	= 1600,
+};
+
+enum ov2640_height_sizes {
+	H_QCIF	= 144,
+	H_QVGA	= 240,
+	H_CIF	= 288,
+	H_VGA	= 480,
+	H_SVGA	= 600,
+	H_XGA	= 768,
+	H_SXGA	= 1024,
+	H_UXGA	= 1200,
+};
+
+struct ov2640_win_size {
+	char                     *name;
+	enum ov2640_width_sizes   width;
+	enum ov2640_height_sizes  height;
+	const struct regval_list *regs;
+};
+
+
+struct ov2640_priv {
+	struct v4l2_subdev		subdev;
+	struct ov2640_camera_info	*info;
+	enum v4l2_mbus_pixelcode	cfmt_code;
+	const struct ov2640_win_size	*win;
+	int				model;
+	u16				flag_vflip:1;
+	u16				flag_hflip:1;
+};
+
+/*
+ * Registers settings
+ */
+
+#define ENDMARKER { 0xff, 0xff }
+
+static const struct regval_list ov2640_init_regs[] = {
+	{ BANK_SEL, BANK_SEL_DSP },
+	{ 0x2c,   0xff },
+	{ 0x2e,   0xdf },
+	{ BANK_SEL, BANK_SEL_SENS },
+	{ 0x3c,   0x32 },
+	{ CLKRC, CLKRC_DIV_SET(1) },
+	{ COM2, COM2_OCAP_Nx_SET(3) },
+	{ REG04, REG04_DEF | REG04_HREF_EN },
+	{ COM8,  COM8_DEF | COM8_BNDF_EN | COM8_AGC_EN | COM8_AEC_EN },
+	{ COM9, COM9_AGC_GAIN_8x | 0x08},
+	{ 0x2c,   0x0c },
+	{ 0x33,   0x78 },
+	{ 0x3a,   0x33 },
+	{ 0x3b,   0xfb },
+	{ 0x3e,   0x00 },
+	{ 0x43,   0x11 },
+	{ 0x16,   0x10 },
+	{ 0x39,   0x02 },
+	{ 0x35,   0x88 },
+	{ 0x22,   0x0a },
+	{ 0x37,   0x40 },
+	{ 0x23,   0x00 },
+	{ ARCOM2, 0xa0 },
+	{ 0x06,   0x02 },
+	{ 0x06,   0x88 },
+	{ 0x07,   0xc0 },
+	{ 0x0d,   0xb7 },
+	{ 0x0e,   0x01 },
+	{ 0x4c,   0x00 },
+	{ 0x4a,   0x81 },
+	{ 0x21,   0x99 },
+	{ AEW,    0x40 },
+	{ AEB,    0x38 },
+	{ VV,     VV_HIGH_TH_SET(0x08) | VV_LOW_TH_SET(0x02) },
+	{ 0x5c,   0x00 },
+	{ 0x63,   0x00 },
+	{ FLL,    0x22 },
+	{ COM3,   0x38 | COM3_BAND_AUTO },
+	{ REG5D,  0x55 },
+	{ REG5E,  0x7d },
+	{ REG5F,  0x7d },
+	{ REG60,  0x55 },
+	{ HISTO_LOW,   0x70 },
+	{ HISTO_HIGH,  0x80 },
+	{ 0x7c,   0x05 },
+	{ 0x20,   0x80 },
+	{ 0x28,   0x30 },
+	{ 0x6c,   0x00 },
+	{ 0x6d,   0x80 },
+	{ 0x6e,   0x00 },
+	{ 0x70,   0x02 },
+	{ 0x71,   0x94 },
+	{ 0x73,   0xc1 },
+	{ 0x3d,   0x34 },
+	{ COM7, COM7_RES_UXGA | COM7_ZOOM_EN },
+	{ 0x5a,   0x57 },
+	{ BD50,   0xbb },
+	{ BD60,   0x9c },
+	{ BANK_SEL, BANK_SEL_DSP },
+	{ 0xe5,   0x7f },
+	{ MC_BIST, MC_BIST_RESET | MC_BIST_BOOT_ROM_SEL },
+	{ 0x41,   0x24 },
+	{ RESET, RESET_JPEG | RESET_DVP },
+	{ 0x76,   0xff },
+	{ 0x33,   0xa0 },
+	{ 0x42,   0x20 },
+	{ 0x43,   0x18 },
+	{ 0x4c,   0x00 },
+	{ CTRL3, CTRL3_BPC_EN | CTRL3_WPC_EN | 0x10 },
+	{ 0x88,   0x3f },
+	{ 0xd7,   0x03 },
+	{ 0xd9,   0x10 },
+	{ R_DVP_SP , R_DVP_SP_AUTO_MODE | 0x2 },
+	{ 0xc8,   0x08 },
+	{ 0xc9,   0x80 },
+	{ BPADDR, 0x00 },
+	{ BPDATA, 0x00 },
+	{ BPADDR, 0x03 },
+	{ BPDATA, 0x48 },
+	{ BPDATA, 0x48 },
+	{ BPADDR, 0x08 },
+	{ BPDATA, 0x20 },
+	{ BPDATA, 0x10 },
+	{ BPDATA, 0x0e },
+	{ 0x90,   0x00 },
+	{ 0x91,   0x0e },
+	{ 0x91,   0x1a },
+	{ 0x91,   0x31 },
+	{ 0x91,   0x5a },
+	{ 0x91,   0x69 },
+	{ 0x91,   0x75 },
+	{ 0x91,   0x7e },
+	{ 0x91,   0x88 },
+	{ 0x91,   0x8f },
+	{ 0x91,   0x96 },
+	{ 0x91,   0xa3 },
+	{ 0x91,   0xaf },
+	{ 0x91,   0xc4 },
+	{ 0x91,   0xd7 },
+	{ 0x91,   0xe8 },
+	{ 0x91,   0x20 },
+	{ 0x92,   0x00 },
+	{ 0x93,   0x06 },
+	{ 0x93,   0xe3 },
+	{ 0x93,   0x03 },
+	{ 0x93,   0x03 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x02 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x00 },
+	{ 0x93,   0x00 },
+	{ 0x96,   0x00 },
+	{ 0x97,   0x08 },
+	{ 0x97,   0x19 },
+	{ 0x97,   0x02 },
+	{ 0x97,   0x0c },
+	{ 0x97,   0x24 },
+	{ 0x97,   0x30 },
+	{ 0x97,   0x28 },
+	{ 0x97,   0x26 },
+	{ 0x97,   0x02 },
+	{ 0x97,   0x98 },
+	{ 0x97,   0x80 },
+	{ 0x97,   0x00 },
+	{ 0x97,   0x00 },
+	{ 0xa4,   0x00 },
+	{ 0xa8,   0x00 },
+	{ 0xc5,   0x11 },
+	{ 0xc6,   0x51 },
+	{ 0xbf,   0x80 },
+	{ 0xc7,   0x10 },
+	{ 0xb6,   0x66 },
+	{ 0xb8,   0xA5 },
+	{ 0xb7,   0x64 },
+	{ 0xb9,   0x7C },
+	{ 0xb3,   0xaf },
+	{ 0xb4,   0x97 },
+	{ 0xb5,   0xFF },
+	{ 0xb0,   0xC5 },
+	{ 0xb1,   0x94 },
+	{ 0xb2,   0x0f },
+	{ 0xc4,   0x5c },
+	{ 0xa6,   0x00 },
+	{ 0xa7,   0x20 },
+	{ 0xa7,   0xd8 },
+	{ 0xa7,   0x1b },
+	{ 0xa7,   0x31 },
+	{ 0xa7,   0x00 },
+	{ 0xa7,   0x18 },
+	{ 0xa7,   0x20 },
+	{ 0xa7,   0xd8 },
+	{ 0xa7,   0x19 },
+	{ 0xa7,   0x31 },
+	{ 0xa7,   0x00 },
+	{ 0xa7,   0x18 },
+	{ 0xa7,   0x20 },
+	{ 0xa7,   0xd8 },
+	{ 0xa7,   0x19 },
+	{ 0xa7,   0x31 },
+	{ 0xa7,   0x00 },
+	{ 0xa7,   0x18 },
+	{ 0x7f,   0x00 },
+	{ 0xe5,   0x1f },
+	{ 0xe1,   0x77 },
+	{ 0xdd,   0x7f },
+	{ CTRL0,  CTRL0_YUV422 | CTRL0_YUV_EN | CTRL0_RGB_EN },
+	ENDMARKER,
+};
+
+/*
+ * register setting for window size
+ * The preamble setup the internal DSP to input a UXGA (1600x1200)
image,
+ * then the different zooming configurations will set up the output
image size.
+ */
+static const struct regval_list ov2640_size_change_preamble_regs[] = {
+	{ BANK_SEL, BANK_SEL_DSP },
+	{ RESET, RESET_DVP },
+	{ HSIZE8, HSIZE8_SET(W_UXGA) }, { VSIZE8, VSIZE8_SET(H_UXGA) },
+	{ CTRL2, CTRL2_DCW_EN | CTRL2_SDE_EN |
+		 CTRL2_UV_AVG_EN | CTRL2_CMX_EN | CTRL2_UV_ADJ_EN },
+	{ HSIZE, HSIZE_SET(W_UXGA) }, { VSIZE,  VSIZE_SET(H_UXGA) },
+	{ XOFFL, XOFFL_SET(0) }, { YOFFL,  YOFFL_SET(0) },
+	{ VHYX, VHYX_HSIZE_SET(W_UXGA) | VHYX_VSIZE_SET(H_UXGA) |
+		VHYX_XOFF_SET(0) | VHYX_YOFF_SET(0)},
+	{ TEST, TEST_HSIZE_SET(W_UXGA) },
+	ENDMARKER,
+};
+
+#define PER_SIZE_REG_SEQ(x, y, v_div, h_div, pclk_div)		\
+	{ CTRLI, CTRLI_LP_DP | CTRLI_V_DIV_SET(v_div) |		\
+		 CTRLI_H_DIV_SET(h_div)},			\
+	{ ZMOW, ZMOW_OUTW_SET(x) }, { ZMOH, ZMOH_OUTH_SET(y) },	\
+	{ ZMHH, ZMHH_OUTW_SET(x) | ZMHH_OUTH_SET(y) },		\
+	{ R_DVP_SP, pclk_div },					\
+	{ RESET, 0x00}
+
+static const struct regval_list ov2640_qcif_regs[] = {
+	PER_SIZE_REG_SEQ(W_QCIF, H_QCIF, 3, 3, 4),
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_qvga_regs[] = {
+	PER_SIZE_REG_SEQ(W_QVGA, H_QVGA, 2, 2, 4),
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_cif_regs[] = {
+	PER_SIZE_REG_SEQ(W_CIF, H_CIF, 2, 2, 8),
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_vga_regs[] = {
+	PER_SIZE_REG_SEQ(W_VGA, H_VGA, 0, 0, 2),
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_svga_regs[] = {
+	PER_SIZE_REG_SEQ(W_SVGA, H_SVGA, 1, 1, 2),
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_xga_regs[] = {
+	PER_SIZE_REG_SEQ(W_XGA, H_XGA, 0, 0, 2),
+	{ CTRLI,    0x00},
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_sxga_regs[] = {
+	PER_SIZE_REG_SEQ(W_SXGA, H_SXGA, 0, 0, 2),
+	{ CTRLI,    0x00},
+	{ R_DVP_SP, 2 | R_DVP_SP_AUTO_MODE },
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_uxga_regs[] = {
+	PER_SIZE_REG_SEQ(W_UXGA, H_UXGA, 0, 0, 0),
+	{ CTRLI,    0x00},
+	{ R_DVP_SP, 0 | R_DVP_SP_AUTO_MODE },
+	ENDMARKER,
+};
+
+#define OV2640_SIZE(n, w, h, r) \
+	{.name = n, .width = w , .height = h, .regs = r }
+
+static const struct ov2640_win_size ov2640_supported_win_sizes[] = {
+	OV2640_SIZE("QCIF", W_QCIF, H_QCIF, ov2640_qcif_regs),
+	OV2640_SIZE("QVGA", W_QVGA, H_QVGA, ov2640_qvga_regs),
+	OV2640_SIZE("CIF", W_CIF, H_CIF, ov2640_cif_regs),
+	OV2640_SIZE("VGA", W_VGA, H_VGA, ov2640_vga_regs),
+	OV2640_SIZE("SVGA", W_SVGA, H_SVGA, ov2640_svga_regs),
+	OV2640_SIZE("XGA", W_XGA, H_XGA, ov2640_xga_regs),
+	OV2640_SIZE("SXGA", W_SXGA, H_SXGA, ov2640_sxga_regs),
+	OV2640_SIZE("UXGA", W_UXGA, H_UXGA, ov2640_uxga_regs),
+};
+
+/*
+ * Register settings for pixel formats
+ */
+static const struct regval_list ov2640_format_change_preamble_regs[] =
{
+	{ BANK_SEL, BANK_SEL_DSP },
+	{ R_BYPASS, R_BYPASS_USE_DSP },
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_yuv422_regs[] = {
+	{ IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_YUV422 },
+	{ 0xD7, 0x01 },
+	{ 0x33, 0xa0 },
+	{ 0xe1, 0x67 },
+	{ RESET,  0x00 },
+	{ R_BYPASS, R_BYPASS_USE_DSP },
+	ENDMARKER,
+};
+
+static const struct regval_list ov2640_rgb565_regs[] = {
+	{ IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_RGB565 },
+	{ 0xd7, 0x03 },
+	{ RESET,  0x00 },
+	{ R_BYPASS, R_BYPASS_USE_DSP },
+	ENDMARKER,
+};
+
+static enum v4l2_mbus_pixelcode ov2640_codes[] = {
+	V4L2_MBUS_FMT_UYVY8_2X8,
+	V4L2_MBUS_FMT_RGB565_2X8_LE,
+};
+
+/*
+ * Supported controls
+ */
+static const struct v4l2_queryctrl ov2640_controls[] = {
+	{
+		.id		= V4L2_CID_VFLIP,
+		.type		= V4L2_CTRL_TYPE_BOOLEAN,
+		.name		= "Flip Vertically",
+		.minimum	= 0,
+		.maximum	= 1,
+		.step		= 1,
+		.default_value	= 0,
+	}, {
+		.id		= V4L2_CID_HFLIP,
+		.type		= V4L2_CTRL_TYPE_BOOLEAN,
+		.name		= "Flip Horizontally",
+		.minimum	= 0,
+		.maximum	= 1,
+		.step		= 1,
+		.default_value	= 0,
+	},
+};
+
+/*
+ * general functions
+ */
+static struct ov2640_priv *to_ov2640(const struct i2c_client *client)
+{
+	return container_of(i2c_get_clientdata(client), struct ov2640_priv,
+			    subdev);
+}
+
+static int ov2640_write_array(struct i2c_client *client,
+			      const struct regval_list *vals)
+{
+	int ret;
+
+	while ((vals->reg_num != 0xff) || (vals->value != 0xff)) {
+		ret = i2c_smbus_write_byte_data(client,
+						    vals->reg_num,
+						    vals->value & 0xFF);
+		dev_vdbg(&client->dev, "array: 0x%02x, 0x%02x",
+			vals->reg_num, vals->value & 0xFF);
+		if (ret < 0)
+			return ret;
+		vals++;
+	}
+	return 0;
+}
+
+static int ov2640_mask_set(struct i2c_client *client,
+			   u8  reg, u8  mask, u8  set)
+{
+	s32 val = i2c_smbus_read_byte_data(client, reg);
+	if (val < 0)
+		return val;
+
+	val &= ~mask;
+	val |= set & mask;
+
+	dev_vdbg(&client->dev, "masks: 0x%02x, 0x%02x",
+			reg, val);
+	return i2c_smbus_write_byte_data(client, reg, val);
+}
+
+static int ov2640_reset(struct i2c_client *client)
+{
+	int ret;
+	const struct regval_list reset_seq[] = {
+		{BANK_SEL, BANK_SEL_SENS},
+		{COM7, COM7_SRST},
+		ENDMARKER,
+	};
+
+	ret = ov2640_write_array(client, reset_seq);
+	if (ret)
+		goto err;
+
+	msleep(5);
+err:
+	dev_dbg(&client->dev, "%s: (ret %d)", __func__, ret);
+	return ret;
+}
+
+/*
+ * soc_camera_ops functions
+ */
+static int ov2640_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	return 0;
+}
+
+static int ov2640_set_bus_param(struct soc_camera_device *icd,
+				unsigned long flags)
+{
+	return 0;
+}
+
+static unsigned long ov2640_query_bus_param(struct soc_camera_device
*icd)
+{
+	struct soc_camera_link *icl = to_soc_camera_link(icd);
+	unsigned long flags = SOCAM_PCLK_SAMPLE_RISING | SOCAM_MASTER |
+		SOCAM_VSYNC_ACTIVE_HIGH | SOCAM_HSYNC_ACTIVE_HIGH |
+		SOCAM_DATA_ACTIVE_HIGH | SOCAM_DATAWIDTH_8 | SOCAM_DATAWIDTH_10;
+
+	return soc_camera_apply_sensor_flags(icl, flags);
+}
+
+static int ov2640_g_ctrl(struct v4l2_subdev *sd, struct v4l2_control
*ctrl)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	struct ov2640_priv *priv = to_ov2640(client);
+
+	switch (ctrl->id) {
+	case V4L2_CID_VFLIP:
+		ctrl->value = priv->flag_vflip;
+		break;
+	case V4L2_CID_HFLIP:
+		ctrl->value = priv->flag_hflip;
+		break;
+	}
+	return 0;
+}
+
+static int ov2640_s_ctrl(struct v4l2_subdev *sd, struct v4l2_control
*ctrl)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	struct ov2640_priv *priv = to_ov2640(client);
+	int ret = 0;
+	u8 val;
+
+	switch (ctrl->id) {
+	case V4L2_CID_VFLIP:
+		val = ctrl->value ? REG04_VFLIP_IMG : 0x00;
+		priv->flag_vflip = ctrl->value ? 1 : 0;
+		ret = ov2640_mask_set(client, REG04, REG04_VFLIP_IMG, val);
+		break;
+	case V4L2_CID_HFLIP:
+		val = ctrl->value ? REG04_HFLIP_IMG : 0x00;
+		priv->flag_hflip = ctrl->value ? 1 : 0;
+		ret = ov2640_mask_set(client, REG04, REG04_HFLIP_IMG, val);
+		break;
+	}
+
+	return ret;
+}
+
+static int ov2640_g_chip_ident(struct v4l2_subdev *sd,
+			       struct v4l2_dbg_chip_ident *id)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	struct ov2640_priv *priv = to_ov2640(client);
+
+	id->ident    = priv->model;
+	id->revision = 0;
+
+	return 0;
+}
+
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+static int ov2640_g_register(struct v4l2_subdev *sd,
+			     struct v4l2_dbg_register *reg)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret;
+
+	reg->size = 1;
+	if (reg->reg > 0xff)
+		return -EINVAL;
+
+	ret = i2c_smbus_read_byte_data(client, reg->reg);
+	if (ret < 0)
+		return ret;
+
+	reg->val = (__u64)ret;
+
+	return 0;
+}
+
+static int ov2640_s_register(struct v4l2_subdev *sd,
+			     struct v4l2_dbg_register *reg)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+	if (reg->reg > 0xff ||
+	    reg->val > 0xff)
+		return -EINVAL;
+
+	return i2c_smbus_write_byte_data(client, reg->reg, reg->val);
+}
+#endif
+
+/* select nearest higher resolution for capture */
+static const struct ov2640_win_size *ov2640_select_win(u32 *width, u32
*height)
+{
+	int i, def = ARRAY_SIZE(ov2640_supported_win_sizes) - 1;
+
+	for (i = 0; i < ARRAY_SIZE(ov2640_supported_win_sizes); i++) {
+		if (ov2640_supported_win_sizes[i].width  >= *width &&
+		    ov2640_supported_win_sizes[i].height >= *height) {
+			*width = ov2640_supported_win_sizes[i].width;
+			*height = ov2640_supported_win_sizes[i].height;
+			return &ov2640_supported_win_sizes[i];
+		}
+	}
+
+	*width = ov2640_supported_win_sizes[def].width;
+	*height = ov2640_supported_win_sizes[def].height;
+	return &ov2640_supported_win_sizes[def];
+}
+
+static int ov2640_set_params(struct i2c_client *client, u32 *width, u32
*height,
+			     enum v4l2_mbus_pixelcode code)
+{
+	struct ov2640_priv *priv = to_ov2640(client);
+	const struct regval_list *selected_cfmt_regs;
+	int ret = -EINVAL;
+
+	/* select win */
+	priv->win = ov2640_select_win(width, height);
+
+	/* select format */
+	priv->cfmt_code = 0;
+	switch (code) {
+	case V4L2_MBUS_FMT_RGB565_2X8_LE:
+		dev_dbg(&client->dev, "%s: Selected cfmt RGB565", __func__);
+		selected_cfmt_regs = ov2640_rgb565_regs;
+		break;
+	default:
+	case V4L2_MBUS_FMT_UYVY8_2X8:
+		dev_dbg(&client->dev, "%s: Selected cfmt YUV422", __func__);
+		selected_cfmt_regs = ov2640_yuv422_regs;
+	}
+
+	/* reset hardware */
+	ov2640_reset(client);
+
+	dev_dbg(&client->dev, "%s: Init default", __func__);
+	/* Initialize the sensor with default data */
+	ret = ov2640_write_array(client, ov2640_init_regs);
+	if (ret < 0)
+		goto err;
+
+	dev_dbg(&client->dev, "%s: Set size to %s", __func__,
priv->win->name);
+	/* Select preamble */
+	ret = ov2640_write_array(client, ov2640_size_change_preamble_regs);
+	if (ret < 0)
+		goto err;
+
+	/* set size win */
+	ret = ov2640_write_array(client, priv->win->regs);
+	if (ret < 0)
+		goto err;
+
+	dev_dbg(&client->dev, "%s: Set cfmt", __func__);
+	/* Cfmt preamble */
+	ret = ov2640_write_array(client, ov2640_format_change_preamble_regs);
+	if (ret < 0)
+		goto err;
+
+	/* set cfmt */
+	ret = ov2640_write_array(client, selected_cfmt_regs);
+	if (ret < 0)
+		goto err;
+
+	priv->cfmt_code = code;
+	*width = priv->win->width;
+	*height = priv->win->height;
+
+	return ret;
+
+err:
+	dev_err(&client->dev, "%s: Error %d", __func__, ret);
+	ov2640_reset(client);
+	priv->win = NULL;
+
+	return ret;
+}
+
+static int ov2640_g_fmt(struct v4l2_subdev *sd,
+			struct v4l2_mbus_framefmt *mf)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	struct ov2640_priv *priv = to_ov2640(client);
+
+	if (!priv->win) {
+		u32 width = W_SVGA, height = H_SVGA;
+		int ret = ov2640_set_params(client, &width, &height,
+					    V4L2_MBUS_FMT_UYVY8_2X8);
+		if (ret < 0)
+			return ret;
+	}
+
+	mf->width	= priv->win->width;
+	mf->height	= priv->win->height;
+	mf->code	= priv->cfmt_code;
+
+	switch (mf->code) {
+	case V4L2_MBUS_FMT_RGB565_2X8_LE:
+		mf->colorspace = V4L2_COLORSPACE_SRGB;
+		break;
+	default:
+	case V4L2_MBUS_FMT_UYVY8_2X8:
+		mf->colorspace = V4L2_COLORSPACE_JPEG;
+	}
+	mf->field	= V4L2_FIELD_NONE;
+
+	return 0;
+}
+
+static int ov2640_s_fmt(struct v4l2_subdev *sd,
+			struct v4l2_mbus_framefmt *mf)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret;
+
+
+	switch (mf->code) {
+	case V4L2_MBUS_FMT_RGB565_2X8_LE:
+		mf->colorspace = V4L2_COLORSPACE_SRGB;
+		break;
+	default:
+		mf->code = V4L2_MBUS_FMT_UYVY8_2X8;
+	case V4L2_MBUS_FMT_UYVY8_2X8:
+		mf->colorspace = V4L2_COLORSPACE_JPEG;
+	}
+
+	ret = ov2640_set_params(client, &mf->width, &mf->height,
+				    mf->code);
+
+	return ret;
+}
+
+static int ov2640_try_fmt(struct v4l2_subdev *sd,
+			  struct v4l2_mbus_framefmt *mf)
+{
+	const struct ov2640_win_size *win;
+
+	/*
+	 * select suitable win
+	 */
+	win = ov2640_select_win(&mf->width, &mf->height);
+
+	mf->field	= V4L2_FIELD_NONE;
+
+	switch (mf->code) {
+	case V4L2_MBUS_FMT_RGB565_2X8_LE:
+		mf->colorspace = V4L2_COLORSPACE_SRGB;
+		break;
+	default:
+		mf->code = V4L2_MBUS_FMT_UYVY8_2X8;
+	case V4L2_MBUS_FMT_UYVY8_2X8:
+		mf->colorspace = V4L2_COLORSPACE_JPEG;
+	}
+
+	return 0;
+}
+
+static int ov2640_enum_fmt(struct v4l2_subdev *sd, unsigned int index,
+			   enum v4l2_mbus_pixelcode *code)
+{
+	if (index >= ARRAY_SIZE(ov2640_codes))
+		return -EINVAL;
+
+	*code = ov2640_codes[index];
+	return 0;
+}
+
+static int ov2640_video_probe(struct soc_camera_device *icd,
+			      struct i2c_client *client)
+{
+	struct ov2640_priv *priv = to_ov2640(client);
+	u8		pid, ver, midh, midl;
+	const char	*devname;
+	int		ret;
+
+	/*
+	 * We must have a parent by now. And it cannot be a wrong one.
+	 * So this entire test is completely redundant.
+	 */
+	if (!icd->dev.parent ||
+	    to_soc_camera_host(icd->dev.parent)->nr != icd->iface) {
+		dev_err(&client->dev, "Parent missing or invalid!\n");
+		ret = -ENODEV;
+		goto err;
+	}
+
+	/*
+	 * check and show product ID and manufacturer ID
+	 */
+	i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS);
+	pid  = i2c_smbus_read_byte_data(client, PID);
+	ver  = i2c_smbus_read_byte_data(client, VER);
+	midh = i2c_smbus_read_byte_data(client, MIDH);
+	midl = i2c_smbus_read_byte_data(client, MIDL);
+
+	switch (VERSION(pid, ver)) {
+	case PID_OV2640:
+		devname     = "ov2640";
+		priv->model = V4L2_IDENT_OV2640;
+		break;
+	default:
+		dev_err(&client->dev,
+			"Product ID error %x:%x\n", pid, ver);
+		ret = -ENODEV;
+		goto err;
+	}
+
+	dev_info(&client->dev,
+		 "%s Product ID %0x:%0x Manufacturer ID %x:%x\n",
+		 devname, pid, ver, midh, midl);
+
+	return 0;
+
+err:
+	return ret;
+}
+
+static struct soc_camera_ops ov2640_ops = {
+	.set_bus_param		= ov2640_set_bus_param,
+	.query_bus_param	= ov2640_query_bus_param,
+	.controls		= ov2640_controls,
+	.num_controls		= ARRAY_SIZE(ov2640_controls),
+};
+
+static struct v4l2_subdev_core_ops ov2640_subdev_core_ops = {
+	.g_ctrl		= ov2640_g_ctrl,
+	.s_ctrl		= ov2640_s_ctrl,
+	.g_chip_ident	= ov2640_g_chip_ident,
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+	.g_register	= ov2640_g_register,
+	.s_register	= ov2640_s_register,
+#endif
+};
+
+static struct v4l2_subdev_video_ops ov2640_subdev_video_ops = {
+	.s_stream	= ov2640_s_stream,
+	.g_mbus_fmt	= ov2640_g_fmt,
+	.s_mbus_fmt	= ov2640_s_fmt,
+	.try_mbus_fmt	= ov2640_try_fmt,
+	.enum_mbus_fmt	= ov2640_enum_fmt,
+};
+
+static struct v4l2_subdev_ops ov2640_subdev_ops = {
+	.core	= &ov2640_subdev_core_ops,
+	.video	= &ov2640_subdev_video_ops,
+};
+
+/*
+ * i2c_driver functions
+ */
+static int ov2640_probe(struct i2c_client *client,
+			const struct i2c_device_id *did)
+{
+	struct ov2640_priv        *priv;
+	struct soc_camera_device  *icd = client->dev.platform_data;
+	struct i2c_adapter        *adapter =
to_i2c_adapter(client->dev.parent);
+	struct soc_camera_link    *icl;
+	int                        ret;
+
+	if (!icd) {
+		dev_err(&adapter->dev, "OV2640: missing soc-camera data!\n");
+		return -EINVAL;
+	}
+
+	icl = to_soc_camera_link(icd);
+	if (!icl) {
+		dev_err(&adapter->dev,
+			"OV2640: Missing platform_data for driver\n");
+		return -EINVAL;
+	}
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+		dev_err(&adapter->dev,
+			"OV2640: I2C-Adapter doesn't support SMBUS\n");
+		return -EIO;
+	}
+
+	priv = kzalloc(sizeof(struct ov2640_priv), GFP_KERNEL);
+	if (!priv) {
+		dev_err(&adapter->dev,
+			"Failed to allocate memory for private data!\n");
+		return -ENOMEM;
+	}
+
+	priv->info = icl->priv;
+
+	v4l2_i2c_subdev_init(&priv->subdev, client, &ov2640_subdev_ops);
+
+	icd->ops	= &ov2640_ops;
+
+	ret = ov2640_video_probe(icd, client);
+	if (ret) {
+		icd->ops = NULL;
+		kfree(priv);
+	} else {
+		dev_info(&adapter->dev, "OV2640 Probed\n");
+	}
+
+	return ret;
+}
+
+static int ov2640_remove(struct i2c_client *client)
+{
+	struct ov2640_priv *priv = to_ov2640(client);
+	struct soc_camera_device *icd = client->dev.platform_data;
+
+	icd->ops = NULL;
+	kfree(priv);
+	return 0;
+}
+
+static const struct i2c_device_id ov2640_id[] = {
+	{ "ov2640", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, ov2640_id);
+
+static struct i2c_driver ov2640_i2c_driver = {
+	.driver = {
+		.name = "ov2640",
+	},
+	.probe    = ov2640_probe,
+	.remove   = ov2640_remove,
+	.id_table = ov2640_id,
+};
+
+/*
+ * module functions
+ */
+static int __init ov2640_module_init(void)
+{
+	return i2c_add_driver(&ov2640_i2c_driver);
+}
+
+static void __exit ov2640_module_exit(void)
+{
+	i2c_del_driver(&ov2640_i2c_driver);
+}
+
+module_init(ov2640_module_init);
+module_exit(ov2640_module_exit);
+
+MODULE_DESCRIPTION("SoC Camera driver for Omni Vision 2640 sensor");
+MODULE_AUTHOR("Alberto Panizzo");
+MODULE_LICENSE("GPL v2");
diff --git a/include/media/v4l2-chip-ident.h
b/include/media/v4l2-chip-ident.h
index 51e89f2..44fe44e 100644
--- a/include/media/v4l2-chip-ident.h
+++ b/include/media/v4l2-chip-ident.h
@@ -74,6 +74,7 @@ enum {
 	V4L2_IDENT_SOI968 = 256,
 	V4L2_IDENT_OV9640 = 257,
 	V4L2_IDENT_OV6650 = 258,
+	V4L2_IDENT_OV2640 = 259,
 
 	/* module saa7146: reserved range 300-309 */
 	V4L2_IDENT_SAA7146 = 300,
-- 
1.6.3.3



--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux