On Fri, Nov 12, 2010 at 4:51 PM, Anca Emanuel <anca.emanuel@xxxxxxxxx> wrote:
> I have an PCIe Leadtek WinFast PxPVR2200 analog TV card with Conexant
> 23885+23417(6) +Xceive silicon tuner.
With this patch I get:
xc2028 1-0061: xc2028/3028 firmware name not set!
diff --git a/drivers/media/video/cx23885/cx23885-cards.c b/drivers/media/video/c
index db05400..5ee5afa 100644
--- a/drivers/media/video/cx23885/cx23885-cards.c
+++ b/drivers/media/video/cx23885/cx23885-cards.c
@@ -309,6 +309,23 @@ struct cx23885_board cx23885_boards[] = {
CX25840_COMPONENT_ON,
} },
},
+ [CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200] = {
+ .name = "LEADTEK WinFast PxPVR2200",
+ .porta = CX23885_ANALOG_VIDEO,
+ .portb = CX23885_MPEG_ENCODER,
+ .tuner_type = TUNER_XC2028,
+ .tuner_addr = 0x61,
+ .input = {{
+ .type = CX23885_VMUX_TELEVISION,
+ .vmux = CX25840_VIN2_CH1 |
+ CX25840_VIN5_CH2 |
+ CX25840_NONE0_CH3,
+ }, {
+ .type = CX23885_VMUX_SVIDEO,
+ .vmux = CX25840_SVIDEO_LUMA3 |
+ CX25840_SVIDEO_CHROMA4,
+ } },
+ },
};
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
@@ -496,6 +513,10 @@ struct cx23885_subid cx23885_subids[] = {
.subvendor = 0x107d,
.subdevice = 0x6f22,
.card = CX23885_BOARD_LEADTEK_WINFAST_PXTV1200,
+ }, {
+ .subvendor = 0x107d,
+ .subdevice = 0x6f21,
+ .card = CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200,
},
};
const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
@@ -791,6 +812,7 @@ void cx23885_gpio_setup(struct cx23885_dev *dev)
cx_set(GP0_IO, 0x00050005);
break;
case CX23885_BOARD_HAUPPAUGE_HVR1700:
+ case CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200:
/* GPIO-0 TDA10048 demodulator reset */
/* GPIO-2 TDA8295A Reset */
/* GPIO-3-10 cx23417 data0-7 */
@@ -1218,6 +1240,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
case CX23885_BOARD_HAUPPAUGE_HVR1850:
case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
case CX23885_BOARD_HAUPPAUGE_HVR1290:
+ case CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200:
default:
ts2->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
@@ -1245,6 +1268,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
case CX23885_BOARD_MAGICPRO_PROHDTVE2:
case CX23885_BOARD_HAUPPAUGE_HVR1290:
case CX23885_BOARD_LEADTEK_WINFAST_PXTV1200:
+ case CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200:
dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev,
&dev->i2c_bus[2].i2c_adap,
NULL, "cx25840", 0x88 >> 1, NULL);
diff --git a/drivers/media/video/cx23885/cx23885.h b/drivers/media/video/cx23885
index ed94b17..0dc8e44 100644
--- a/drivers/media/video/cx23885/cx23885.h
+++ b/drivers/media/video/cx23885/cx23885.h
@@ -84,6 +84,7 @@
#define CX23885_BOARD_HAUPPAUGE_HVR1290 26
#define CX23885_BOARD_MYGICA_X8558PRO 27
#define CX23885_BOARD_LEADTEK_WINFAST_PXTV1200 28
+#define CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200 29
#define GPIO_0 0x00000001
#define GPIO_1 0x00000002
diff --git a/drivers/media/video/gspca/ov519.c b/drivers/media/video/gspca/ov519
index 6cf6855..46c62ec 100644
diff --git a/drivers/media/video/cx23885/cx23885-cards.c b/drivers/media/video/c
index db05400..5ee5afa 100644
--- a/drivers/media/video/cx23885/cx23885-cards.c
+++ b/drivers/media/video/cx23885/cx23885-cards.c
@@ -309,6 +309,23 @@ struct cx23885_board cx23885_boards[] = {
CX25840_COMPONENT_ON,
} },
},
+ [CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200] = {
+ .name = "LEADTEK WinFast PxPVR2200",
+ .porta = CX23885_ANALOG_VIDEO,
+ .portb = CX23885_MPEG_ENCODER,
+ .tuner_type = TUNER_XC2028,
+ .tuner_addr = 0x61,
+ .input = {{
+ .type = CX23885_VMUX_TELEVISION,
+ .vmux = CX25840_VIN2_CH1 |
+ CX25840_VIN5_CH2 |
+ CX25840_NONE0_CH3,
+ }, {
+ .type = CX23885_VMUX_SVIDEO,
+ .vmux = CX25840_SVIDEO_LUMA3 |
+ CX25840_SVIDEO_CHROMA4,
+ } },
+ },
};
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
@@ -496,6 +513,10 @@ struct cx23885_subid cx23885_subids[] = {
.subvendor = 0x107d,
.subdevice = 0x6f22,
.card = CX23885_BOARD_LEADTEK_WINFAST_PXTV1200,
+ }, {
+ .subvendor = 0x107d,
+ .subdevice = 0x6f21,
+ .card = CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200,
},
};
const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
@@ -791,6 +812,7 @@ void cx23885_gpio_setup(struct cx23885_dev *dev)
cx_set(GP0_IO, 0x00050005);
break;
case CX23885_BOARD_HAUPPAUGE_HVR1700:
+ case CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200:
/* GPIO-0 TDA10048 demodulator reset */
/* GPIO-2 TDA8295A Reset */
/* GPIO-3-10 cx23417 data0-7 */
@@ -1218,6 +1240,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
case CX23885_BOARD_HAUPPAUGE_HVR1850:
case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
case CX23885_BOARD_HAUPPAUGE_HVR1290:
+ case CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200:
default:
ts2->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
@@ -1245,6 +1268,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
case CX23885_BOARD_MAGICPRO_PROHDTVE2:
case CX23885_BOARD_HAUPPAUGE_HVR1290:
case CX23885_BOARD_LEADTEK_WINFAST_PXTV1200:
+ case CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200:
dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev,
&dev->i2c_bus[2].i2c_adap,
NULL, "cx25840", 0x88 >> 1, NULL);
diff --git a/drivers/media/video/cx23885/cx23885.h b/drivers/media/video/cx23885
index ed94b17..0dc8e44 100644
--- a/drivers/media/video/cx23885/cx23885.h
+++ b/drivers/media/video/cx23885/cx23885.h
@@ -84,6 +84,7 @@
#define CX23885_BOARD_HAUPPAUGE_HVR1290 26
#define CX23885_BOARD_MYGICA_X8558PRO 27
#define CX23885_BOARD_LEADTEK_WINFAST_PXTV1200 28
+#define CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200 29
#define GPIO_0 0x00000001
#define GPIO_1 0x00000002
diff --git a/drivers/media/video/gspca/ov519.c b/drivers/media/video/gspca/ov519
index 6cf6855..46c62ec 100644
&dev->i2c_bus[2].i2c_adap,
NULL, "cx25840", 0x88 >> 1, NULL);
diff --git a/drivers/media/video/cx23885/cx23885.h b/drivers/media/video/cx23885
index ed94b17..0dc8e44 100644
--- a/drivers/media/video/cx23885/cx23885.h
+++ b/drivers/media/video/cx23885/cx23885.h
@@ -84,6 +84,7 @@
#define CX23885_BOARD_HAUPPAUGE_HVR1290 26
#define CX23885_BOARD_MYGICA_X8558PRO 27
#define CX23885_BOARD_LEADTEK_WINFAST_PXTV1200 28
+#define CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200 29
#define GPIO_0 0x00000001
#define GPIO_1 0x00000002
Log attached.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.37-rc1-git8t5+ (root@ubuntu) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #6 SMP Fri Nov 12 23:51:16 EET 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e3000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
[ 0.000000] BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ffbe000 - 000000007fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] DMI present.
[ 0.000000] DMI: MS-7360/MS-7360, BIOS V1.10 11/11/2008
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x7ffb0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ bfb000-c00000
[ 0.000000] RAMDISK: 3759e000 - 37ff0000
[ 0.000000] Allocated new RAMDISK: 36b4c000 - 3759d1bf
[ 0.000000] Move RAMDISK from 000000003759e000 - 0000000037fef1be to 36b4c000 - 3759d1be
[ 0.000000] ACPI: RSDP 000f9bb0 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 7ffb0000 00040 (v01 111108 RSDT0906 20081111 MSFT 00000097)
[ 0.000000] ACPI: FACP 7ffb0200 00084 (v01 111108 FACP0906 20081111 MSFT 00000097)
[ 0.000000] ACPI: DSDT 7ffb0440 05595 (v01 0AAAA 0AAAA000 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 7ffbe000 00040
[ 0.000000] ACPI: APIC 7ffb0390 0006C (v01 111108 APIC0906 20081111 MSFT 00000097)
[ 0.000000] ACPI: MCFG 7ffb0400 0003C (v01 111108 OEMMCFG 20081111 MSFT 00000097)
[ 0.000000] ACPI: OEMB 7ffbe040 00071 (v01 111108 OEMB0906 20081111 MSFT 00000097)
[ 0.000000] ACPI: HPET 7ffb59e0 00038 (v01 111108 OEMHPET 20081111 MSFT 00000097)
[ 0.000000] ACPI: GSCI 7ffbe0c0 02024 (v01 111108 GMCHSCI 20081111 MSFT 00000097)
[ 0.000000] ACPI: SSDT 7ffc0570 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1159MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0007ffb0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007ffb0
[ 0.000000] On node 0 totalpages: 524095
[ 0.000000] free_area_init_node: node 0, pgdat c077c800, node_mem_map f5b4c200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2320 pages used for memmap
[ 0.000000] HighMem zone: 294562 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e3000
[ 0.000000] PM: Registered nosave memory: 00000000000e3000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:7ee00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 12 pages/cpu @f5400000 s27904 r0 d21248 u1048576
[ 0.000000] pcpu-alloc: s27904 r0 d21248 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519999
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.37-rc1-git8t5+ root=UUID=d4578a46-8171-4c14-886f-0444e0b81032 ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 10483840 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:0007ffb0)
[ 0.000000] Memory: 2050184k/2096832k available (4951k kernel code, 46196k reserved, 1792k data, 680k init, 1187528k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc0797000 - 0xc0841000 ( 680 kB)
[ 0.000000] .data : 0xc05d5f46 - 0xc0796048 (1792 kB)
[ 0.000000] .text : 0xc0100000 - 0xc05d5f46 (4951 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f4408000 soft=f440a000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2000.732 MHz processor.
[ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4001.46 BogoMIPS (lpj=8002928)
[ 0.004011] pid_max: default: 32768 minimum: 301
[ 0.004035] Security Framework initialized
[ 0.004050] AppArmor: AppArmor initialized
[ 0.004064] Mount-cache hash table entries: 512
[ 0.004204] Initializing cgroup subsys ns
[ 0.004209] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.004212] Initializing cgroup subsys cpuacct
[ 0.004217] Initializing cgroup subsys memory
[ 0.004227] Initializing cgroup subsys devices
[ 0.004229] Initializing cgroup subsys freezer
[ 0.004232] Initializing cgroup subsys net_cls
[ 0.004264] CPU: Physical Processor ID: 0
[ 0.004266] CPU: Processor Core ID: 0
[ 0.004269] mce: CPU supports 6 MCE banks
[ 0.004277] CPU0: Thermal monitoring enabled (TM2)
[ 0.004280] using mwait in idle threads.
[ 0.004287] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.004293] PEBS disabled due to CPU errata.
[ 0.004299] ... version: 2
[ 0.004301] ... bit width: 40
[ 0.004303] ... generic registers: 2
[ 0.004305] ... value mask: 000000ffffffffff
[ 0.004307] ... max period: 000000007fffffff
[ 0.004309] ... fixed-purpose events: 3
[ 0.004311] ... event mask: 0000000700000003
[ 0.009611] ACPI: Core revision 20101013
[ 0.017053] ftrace: allocating 20679 entries in 41 pages
[ 0.020054] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.020361] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.062722] CPU0: Intel(R) Pentium(R) Dual CPU E2180 @ 2.00GHz stepping 0d
[ 0.064000] CPU 1 irqstacks, hard=f44aa000 soft=f44ac000
[ 0.064000] Booting Node 0, Processors #1
[ 0.008000] Initializing CPU#1
[ 0.152015] Brought up 2 CPUs
[ 0.152018] Total of 2 processors activated (8002.79 BogoMIPS).
[ 0.152402] devtmpfs: initialized
[ 0.153144] regulator: core version 0.5
[ 0.153192] regulator: dummy:
[ 0.153212] Time: 0:07:01 Date: 11/13/10
[ 0.153254] NET: Registered protocol family 16
[ 0.153378] EISA bus registered
[ 0.153386] ACPI: bus type pci registered
[ 0.153474] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.153477] PCI: not using MMCONFIG
[ 0.153643] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
[ 0.153646] PCI: Using configuration type 1 for base access
[ 0.154598] bio: create slab <bio-0> at 0
[ 0.157043] ACPI: EC: Look up EC in DSDT
[ 0.158795] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.163833] ACPI: SSDT 7ffc00f0 00235 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
[ 0.164222] ACPI: Dynamic OEM Table Load:
[ 0.164226] ACPI: SSDT (null) 00235 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
[ 0.164709] ACPI: SSDT 7ffc0330 00235 (v01 DpgPmm P002Ist 00000012 INTL 20051117)
[ 0.165088] ACPI: Dynamic OEM Table Load:
[ 0.165091] ACPI: SSDT (null) 00235 (v01 DpgPmm P002Ist 00000012 INTL 20051117)
[ 0.165443] ACPI: Interpreter enabled
[ 0.165453] ACPI: (supports S0 S3 S4 S5)
[ 0.165476] ACPI: Using IOAPIC for interrupt routing
[ 0.165510] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.167238] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.167241] PCI: Using MMCONFIG for extended config space
[ 0.174883] ACPI: No dock devices found.
[ 0.174888] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.175183] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.175475] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.175478] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.175482] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.175485] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.175488] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xdfffffff]
[ 0.175492] pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xffffffff]
[ 0.175504] pci 0000:00:00.0: [8086:29c0] type 0 class 0x000600
[ 0.175554] pci 0000:00:01.0: [8086:29c1] type 1 class 0x000604
[ 0.175594] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.175597] pci 0000:00:01.0: PME# disabled
[ 0.175641] pci 0000:00:1a.0: [8086:2937] type 0 class 0x000c03
[ 0.175688] pci 0000:00:1a.0: reg 20: [io 0xbc00-0xbc1f]
[ 0.175736] pci 0000:00:1a.1: [8086:2938] type 0 class 0x000c03
[ 0.175783] pci 0000:00:1a.1: reg 20: [io 0xb880-0xb89f]
[ 0.175841] pci 0000:00:1a.7: [8086:293c] type 0 class 0x000c03
[ 0.175864] pci 0000:00:1a.7: reg 10: [mem 0xf9fffc00-0xf9ffffff]
[ 0.175943] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.175948] pci 0000:00:1a.7: PME# disabled
[ 0.175973] pci 0000:00:1b.0: [8086:293e] type 0 class 0x000403
[ 0.175990] pci 0000:00:1b.0: reg 10: [mem 0xf9ff8000-0xf9ffbfff 64bit]
[ 0.176061] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.176065] pci 0000:00:1b.0: PME# disabled
[ 0.176087] pci 0000:00:1c.0: [8086:2940] type 1 class 0x000604
[ 0.176147] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.176151] pci 0000:00:1c.0: PME# disabled
[ 0.176175] pci 0000:00:1c.2: [8086:2944] type 1 class 0x000604
[ 0.176235] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.176240] pci 0000:00:1c.2: PME# disabled
[ 0.176264] pci 0000:00:1c.4: [8086:2948] type 1 class 0x000604
[ 0.176324] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.176328] pci 0000:00:1c.4: PME# disabled
[ 0.176351] pci 0000:00:1c.5: [8086:294a] type 1 class 0x000604
[ 0.176412] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.176416] pci 0000:00:1c.5: PME# disabled
[ 0.176441] pci 0000:00:1d.0: [8086:2934] type 0 class 0x000c03
[ 0.176488] pci 0000:00:1d.0: reg 20: [io 0xb800-0xb81f]
[ 0.176535] pci 0000:00:1d.1: [8086:2935] type 0 class 0x000c03
[ 0.176582] pci 0000:00:1d.1: reg 20: [io 0xb480-0xb49f]
[ 0.176629] pci 0000:00:1d.2: [8086:2936] type 0 class 0x000c03
[ 0.176676] pci 0000:00:1d.2: reg 20: [io 0xb400-0xb41f]
[ 0.176723] pci 0000:00:1d.3: [8086:2939] type 0 class 0x000c03
[ 0.176770] pci 0000:00:1d.3: reg 20: [io 0xb080-0xb09f]
[ 0.176828] pci 0000:00:1d.7: [8086:293a] type 0 class 0x000c03
[ 0.176851] pci 0000:00:1d.7: reg 10: [mem 0xf9fff800-0xf9fffbff]
[ 0.176930] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.176935] pci 0000:00:1d.7: PME# disabled
[ 0.176955] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[ 0.177016] pci 0000:00:1f.0: [8086:2918] type 0 class 0x000601
[ 0.177098] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.177102] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
[ 0.177107] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
[ 0.177148] pci 0000:00:1f.2: [8086:2921] type 0 class 0x000101
[ 0.177165] pci 0000:00:1f.2: reg 10: [io 0xb000-0xb007]
[ 0.177175] pci 0000:00:1f.2: reg 14: [io 0xac00-0xac03]
[ 0.177184] pci 0000:00:1f.2: reg 18: [io 0xa880-0xa887]
[ 0.177193] pci 0000:00:1f.2: reg 1c: [io 0xa800-0xa803]
[ 0.177203] pci 0000:00:1f.2: reg 20: [io 0xa480-0xa48f]
[ 0.177212] pci 0000:00:1f.2: reg 24: [io 0xa400-0xa40f]
[ 0.177252] pci 0000:00:1f.3: [8086:2930] type 0 class 0x000c05
[ 0.177269] pci 0000:00:1f.3: reg 10: [mem 0xf9fff400-0xf9fff4ff 64bit]
[ 0.177293] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.177328] pci 0000:00:1f.5: [8086:2926] type 0 class 0x000101
[ 0.177345] pci 0000:00:1f.5: reg 10: [io 0xa000-0xa007]
[ 0.177354] pci 0000:00:1f.5: reg 14: [io 0x9c00-0x9c03]
[ 0.177364] pci 0000:00:1f.5: reg 18: [io 0x9880-0x9887]
[ 0.177373] pci 0000:00:1f.5: reg 1c: [io 0x9800-0x9803]
[ 0.177382] pci 0000:00:1f.5: reg 20: [io 0x9480-0x948f]
[ 0.177391] pci 0000:00:1f.5: reg 24: [io 0x9400-0x940f]
[ 0.177470] pci 0000:01:00.0: [10de:0611] type 0 class 0x000300
[ 0.177482] pci 0000:01:00.0: reg 10: [mem 0xfd000000-0xfdffffff]
[ 0.177495] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.177507] pci 0000:01:00.0: reg 1c: [mem 0xfa000000-0xfbffffff 64bit]
[ 0.177517] pci 0000:01:00.0: reg 24: [io 0xcc00-0xcc7f]
[ 0.177526] pci 0000:01:00.0: reg 30: [mem 0xfe7e0000-0xfe7fffff pref]
[ 0.177575] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.177579] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.177583] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfe7fffff]
[ 0.177588] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.177632] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.177636] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.177641] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.177648] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.177706] pci 0000:03:00.0: [14f1:8852] type 0 class 0x000400
[ 0.177736] pci 0000:03:00.0: reg 10: [mem 0xfe800000-0xfe9fffff 64bit]
[ 0.177847] pci 0000:03:00.0: supports D1 D2
[ 0.177850] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.177856] pci 0000:03:00.0: PME# disabled
[ 0.177881] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.177892] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 0.177897] pci 0000:00:1c.2: bridge window [io 0xf000-0x0000] (disabled)
[ 0.177902] pci 0000:00:1c.2: bridge window [mem 0xfe800000-0xfe9fffff]
[ 0.177909] pci 0000:00:1c.2: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.177970] pci 0000:04:00.0: [11ab:6121] type 0 class 0x000101
[ 0.177988] pci 0000:04:00.0: reg 10: [io 0xdc00-0xdc07]
[ 0.178001] pci 0000:04:00.0: reg 14: [io 0xd880-0xd883]
[ 0.178014] pci 0000:04:00.0: reg 18: [io 0xd800-0xd807]
[ 0.178027] pci 0000:04:00.0: reg 1c: [io 0xd480-0xd483]
[ 0.178040] pci 0000:04:00.0: reg 20: [io 0xd400-0xd40f]
[ 0.178053] pci 0000:04:00.0: reg 24: [mem 0xfeaffc00-0xfeafffff]
[ 0.178100] pci 0000:04:00.0: supports D1
[ 0.178103] pci 0000:04:00.0: PME# supported from D0 D1 D3hot
[ 0.178108] pci 0000:04:00.0: PME# disabled
[ 0.178127] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.178137] pci 0000:00:1c.4: PCI bridge to [bus 04-04]
[ 0.178142] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.178146] pci 0000:00:1c.4: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.178153] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.178220] pci 0000:05:00.0: [10ec:8168] type 0 class 0x000200
[ 0.178240] pci 0000:05:00.0: reg 10: [io 0xe800-0xe8ff]
[ 0.178273] pci 0000:05:00.0: reg 18: [mem 0xfebff000-0xfebfffff 64bit]
[ 0.178312] pci 0000:05:00.0: reg 30: [mem 0xfebc0000-0xfebdffff pref]
[ 0.178362] pci 0000:05:00.0: supports D1 D2
[ 0.178364] pci 0000:05:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.178370] pci 0000:05:00.0: PME# disabled
[ 0.178394] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.178405] pci 0000:00:1c.5: PCI bridge to [bus 05-05]
[ 0.178410] pci 0000:00:1c.5: bridge window [io 0xe000-0xefff]
[ 0.178414] pci 0000:00:1c.5: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.178421] pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.178488] pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
[ 0.178492] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.178497] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.178504] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.178507] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.178510] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.178513] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.178516] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.178519] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xdfffffff] (subtractive decode)
[ 0.178522] pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xffffffff] (subtractive decode)
[ 0.178549] pci_bus 0000:00: on NUMA node 0
[ 0.178552] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.178742] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.178885] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.178944] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 0.179003] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.179060] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.191204] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15)
[ 0.191273] ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
[ 0.191335] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12 14 15)
[ 0.191401] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12 14 *15)
[ 0.191466] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
[ 0.191534] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12 *14 15)
[ 0.191600] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 6 7 10 11 12 14 15)
[ 0.191665] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 *7 10 11 12 14 15)
[ 0.191701] HEST: Table is not found!
[ 0.191793] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.191798] vgaarb: loaded
[ 0.191958] SCSI subsystem initialized
[ 0.191971] libata version 3.00 loaded.
[ 0.192028] usbcore: registered new interface driver usbfs
[ 0.192041] usbcore: registered new interface driver hub
[ 0.192046] usbcore: registered new device driver usb
[ 0.192051] wmi: Mapper loaded
[ 0.192054] PCI: Using ACPI for IRQ routing
[ 0.192058] PCI: pci_cache_line_size set to 64 bytes
[ 0.192164] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.192167] reserve RAM buffer: 000000007ffb0000 - 000000007fffffff
[ 0.192276] NetLabel: Initializing
[ 0.192279] NetLabel: domain hash size = 128
[ 0.192280] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.192293] NetLabel: unlabeled traffic allowed by default
[ 0.192338] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.192344] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.192351] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.196024] Switching to clocksource tsc
[ 0.204391] AppArmor: AppArmor Filesystem Enabled
[ 0.204409] pnp: PnP ACPI init
[ 0.204437] ACPI: bus type pnp registered
[ 0.204617] pnp 00:00: [bus 00-ff]
[ 0.204620] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.204623] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.204626] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.204629] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.204632] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[ 0.204635] pnp 00:00: [mem 0x80000000-0xdfffffff window]
[ 0.204637] pnp 00:00: [mem 0xf0000000-0xffffffff window]
[ 0.204718] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.204730] pnp 00:01: [mem 0xfed14000-0xfed19fff]
[ 0.204793] pnp 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.204834] pnp 00:02: [dma 4]
[ 0.204837] pnp 00:02: [io 0x0000-0x000f]
[ 0.204839] pnp 00:02: [io 0x0081-0x0083]
[ 0.204842] pnp 00:02: [io 0x0087]
[ 0.204844] pnp 00:02: [io 0x0089-0x008b]
[ 0.204846] pnp 00:02: [io 0x008f]
[ 0.204849] pnp 00:02: [io 0x00c0-0x00df]
[ 0.204886] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.204899] pnp 00:03: [io 0x0070-0x0071]
[ 0.204912] pnp 00:03: [irq 8]
[ 0.204945] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.204956] pnp 00:04: [io 0x0061]
[ 0.204988] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.204999] pnp 00:05: [io 0x00f0-0x00ff]
[ 0.205004] pnp 00:05: [irq 13]
[ 0.205040] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.205397] pnp 00:06: [io 0x03f8-0x03ff]
[ 0.205403] pnp 00:06: [irq 4]
[ 0.205406] pnp 00:06: [dma 0 disabled]
[ 0.205482] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.205825] pnp 00:07: [io 0x0060]
[ 0.205828] pnp 00:07: [io 0x0064]
[ 0.205833] pnp 00:07: [irq 1]
[ 0.205871] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.205931] pnp 00:08: [irq 12]
[ 0.205968] pnp 00:08: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[ 0.206123] pnp 00:09: [io 0x0000-0xffffffff disabled]
[ 0.206126] pnp 00:09: [io 0x0a00-0x0adf]
[ 0.206128] pnp 00:09: [io 0x0ae0-0x0aef]
[ 0.206189] pnp 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206321] pnp 00:0a: [io 0x0010-0x001f]
[ 0.206324] pnp 00:0a: [io 0x0022-0x003f]
[ 0.206326] pnp 00:0a: [io 0x0044-0x005f]
[ 0.206329] pnp 00:0a: [io 0x0062-0x0063]
[ 0.206331] pnp 00:0a: [io 0x0065-0x006f]
[ 0.206334] pnp 00:0a: [io 0x0072-0x007f]
[ 0.206336] pnp 00:0a: [io 0x0080]
[ 0.206338] pnp 00:0a: [io 0x0084-0x0086]
[ 0.206341] pnp 00:0a: [io 0x0088]
[ 0.206343] pnp 00:0a: [io 0x008c-0x008e]
[ 0.206346] pnp 00:0a: [io 0x0090-0x009f]
[ 0.206348] pnp 00:0a: [io 0x00a2-0x00bf]
[ 0.206351] pnp 00:0a: [io 0x00e0-0x00ef]
[ 0.206353] pnp 00:0a: [io 0x04d0-0x04d1]
[ 0.206356] pnp 00:0a: [io 0x0800-0x087f]
[ 0.206358] pnp 00:0a: [io 0x0000-0xffffffff disabled]
[ 0.206361] pnp 00:0a: [io 0x0480-0x04bf]
[ 0.206364] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[ 0.206366] pnp 00:0a: [mem 0xfed20000-0xfed8ffff]
[ 0.206453] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206534] pnp 00:0b: [mem 0xfed00000-0xfed003ff]
[ 0.206572] pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.206651] pnp 00:0c: [mem 0xffb00000-0xffbfffff]
[ 0.206654] pnp 00:0c: [mem 0xfff00000-0xffffffff]
[ 0.206691] pnp 00:0c: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.206767] pnp 00:0d: [mem 0xffc00000-0xffefffff]
[ 0.206830] pnp 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206972] pnp 00:0e: [mem 0xfec00000-0xfec00fff]
[ 0.206975] pnp 00:0e: [mem 0xfee00000-0xfee00fff]
[ 0.207036] pnp 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.207089] pnp 00:0f: [mem 0xe0000000-0xefffffff]
[ 0.207150] pnp 00:0f: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.207417] pnp 00:10: [mem 0x00000000-0x0009ffff]
[ 0.207420] pnp 00:10: [mem 0x000c0000-0x000cffff]
[ 0.207422] pnp 00:10: [mem 0x000e0000-0x000fffff]
[ 0.207425] pnp 00:10: [mem 0x00100000-0x7fffffff]
[ 0.207428] pnp 00:10: [mem 0x00000000-0xffffffff disabled]
[ 0.207503] pnp 00:10: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.207677] pnp: PnP ACPI: found 17 devices
[ 0.207679] ACPI: ACPI bus type pnp unregistered
[ 0.207684] PnPBIOS: Disabled by ACPI PNP
[ 0.207696] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
[ 0.207706] system 00:09: [io 0x0a00-0x0adf] has been reserved
[ 0.207709] system 00:09: [io 0x0ae0-0x0aef] has been reserved
[ 0.207716] system 00:0a: [io 0x04d0-0x04d1] has been reserved
[ 0.207719] system 00:0a: [io 0x0800-0x087f] has been reserved
[ 0.207722] system 00:0a: [io 0x0480-0x04bf] has been reserved
[ 0.207726] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.207729] system 00:0a: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.207736] system 00:0d: [mem 0xffc00000-0xffefffff] has been reserved
[ 0.207742] system 00:0e: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.207745] system 00:0e: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.207751] system 00:0f: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.207757] system 00:10: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.207761] system 00:10: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.207764] system 00:10: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.207768] system 00:10: [mem 0x00100000-0x7fffffff] could not be reserved
[ 0.244396] pci 0000:00:1c.0: BAR 14: assigned [mem 0xff900000-0xffafffff]
[ 0.244401] pci 0000:00:1c.0: BAR 15: assigned [mem 0xff700000-0xff8fffff 64bit pref]
[ 0.244406] pci 0000:00:1c.2: BAR 15: assigned [mem 0xff500000-0xff6fffff 64bit pref]
[ 0.244411] pci 0000:00:1c.4: BAR 15: assigned [mem 0xff300000-0xff4fffff 64bit pref]
[ 0.244415] pci 0000:00:1c.5: BAR 15: assigned [mem 0xff100000-0xff2fffff 64bit pref]
[ 0.244419] pci 0000:00:1c.0: BAR 13: assigned [io 0xf000-0xffff]
[ 0.244423] pci 0000:00:1c.2: BAR 13: assigned [io 0x8000-0x8fff]
[ 0.244426] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.244430] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.244435] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfe7fffff]
[ 0.244439] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.244444] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.244448] pci 0000:00:1c.0: bridge window [io 0xf000-0xffff]
[ 0.244453] pci 0000:00:1c.0: bridge window [mem 0xff900000-0xffafffff]
[ 0.244458] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff8fffff 64bit pref]
[ 0.244465] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 0.244468] pci 0000:00:1c.2: bridge window [io 0x8000-0x8fff]
[ 0.244474] pci 0000:00:1c.2: bridge window [mem 0xfe800000-0xfe9fffff]
[ 0.244479] pci 0000:00:1c.2: bridge window [mem 0xff500000-0xff6fffff 64bit pref]
[ 0.244486] pci 0000:00:1c.4: PCI bridge to [bus 04-04]
[ 0.244489] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.244495] pci 0000:00:1c.4: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.244499] pci 0000:00:1c.4: bridge window [mem 0xff300000-0xff4fffff 64bit pref]
[ 0.244506] pci 0000:00:1c.5: PCI bridge to [bus 05-05]
[ 0.244509] pci 0000:00:1c.5: bridge window [io 0xe000-0xefff]
[ 0.244515] pci 0000:00:1c.5: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.244520] pci 0000:00:1c.5: bridge window [mem 0xff100000-0xff2fffff 64bit pref]
[ 0.244527] pci 0000:00:1e.0: PCI bridge to [bus 06-06]
[ 0.244529] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.244534] pci 0000:00:1e.0: bridge window [mem disabled]
[ 0.244538] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.244559] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.244563] pci 0000:00:01.0: setting latency timer to 64
[ 0.244572] pci 0000:00:1c.0: enabling device (0104 -> 0107)
[ 0.244579] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.244583] pci 0000:00:1c.0: setting latency timer to 64
[ 0.244592] pci 0000:00:1c.2: enabling device (0106 -> 0107)
[ 0.244598] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.244602] pci 0000:00:1c.2: setting latency timer to 64
[ 0.244611] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.244616] pci 0000:00:1c.4: setting latency timer to 64
[ 0.244625] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.244629] pci 0000:00:1c.5: setting latency timer to 64
[ 0.244636] pci 0000:00:1e.0: setting latency timer to 64
[ 0.244640] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.244643] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.244646] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.244649] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.244652] pci_bus 0000:00: resource 8 [mem 0x80000000-0xdfffffff]
[ 0.244655] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff]
[ 0.244658] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.244661] pci_bus 0000:01: resource 1 [mem 0xfa000000-0xfe7fffff]
[ 0.244664] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.244667] pci_bus 0000:02: resource 0 [io 0xf000-0xffff]
[ 0.244669] pci_bus 0000:02: resource 1 [mem 0xff900000-0xffafffff]
[ 0.244672] pci_bus 0000:02: resource 2 [mem 0xff700000-0xff8fffff 64bit pref]
[ 0.244675] pci_bus 0000:03: resource 0 [io 0x8000-0x8fff]
[ 0.244678] pci_bus 0000:03: resource 1 [mem 0xfe800000-0xfe9fffff]
[ 0.244681] pci_bus 0000:03: resource 2 [mem 0xff500000-0xff6fffff 64bit pref]
[ 0.244684] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.244686] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.244689] pci_bus 0000:04: resource 2 [mem 0xff300000-0xff4fffff 64bit pref]
[ 0.244692] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.244695] pci_bus 0000:05: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.244698] pci_bus 0000:05: resource 2 [mem 0xff100000-0xff2fffff 64bit pref]
[ 0.244701] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7]
[ 0.244704] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff]
[ 0.244707] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.244710] pci_bus 0000:06: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.244712] pci_bus 0000:06: resource 8 [mem 0x80000000-0xdfffffff]
[ 0.244715] pci_bus 0000:06: resource 9 [mem 0xf0000000-0xffffffff]
[ 0.244755] NET: Registered protocol family 2
[ 0.244830] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.245075] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.245478] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.245724] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.245727] TCP reno registered
[ 0.245731] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.245741] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.245869] NET: Registered protocol family 1
[ 0.245897] pci 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.245899] pci 0000:00:1a.0: Performing full reset
[ 0.245917] pci 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.245919] pci 0000:00:1a.1: Performing full reset
[ 0.245975] pci 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.245977] pci 0000:00:1d.0: Performing full reset
[ 0.245994] pci 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.245997] pci 0000:00:1d.1: Performing full reset
[ 0.246014] pci 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.246016] pci 0000:00:1d.2: Performing full reset
[ 0.246033] pci 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.246035] pci 0000:00:1d.3: Performing full reset
[ 0.246084] pci 0000:01:00.0: Boot video device
[ 0.246097] PCI: CLS 32 bytes, default 64
[ 0.246160] Trying to unpack rootfs image as initramfs...
[ 0.517178] Freeing initrd memory: 10568k freed
[ 0.522226] cpufreq-nforce2: No nForce2 chipset.
[ 0.522265] Scanning for low memory corruption every 60 seconds
[ 0.522385] audit: initializing netlink socket (disabled)
[ 0.522399] type=2000 audit(1289606820.516:1): initialized
[ 0.527206] highmem bounce pool size: 64 pages
[ 0.527211] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.529146] VFS: Disk quotas dquot_6.5.2
[ 0.529216] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.529951] fuse init (API version 7.15)
[ 0.530063] msgmni has been set to 1705
[ 0.530269] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.530272] io scheduler noop registered
[ 0.530274] io scheduler deadline registered
[ 0.530290] io scheduler cfq registered (default)
[ 0.530726] pcieport 0000:00:01.0: ACPI _OSC control granted for 0x1d
[ 0.530739] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.530775] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.530847] pcieport 0000:00:1c.0: ACPI _OSC control granted for 0x1d
[ 0.530860] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.530899] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.530997] pcieport 0000:00:1c.2: ACPI _OSC control granted for 0x1d
[ 0.531010] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.531048] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[ 0.531144] pcieport 0000:00:1c.4: ACPI _OSC control granted for 0x1d
[ 0.531157] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.531195] pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X
[ 0.531295] pcieport 0000:00:1c.5: ACPI _OSC control granted for 0x1d
[ 0.531308] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.531346] pcieport 0000:00:1c.5: irq 44 for MSI/MSI-X
[ 0.531481] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[ 0.531484] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.531489] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
[ 0.531508] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 0.531513] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 0.531533] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[ 0.531535] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 0.531540] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
[ 0.531559] pcieport 0000:00:1c.4: Signaling PME through PCIe PME interrupt
[ 0.531562] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt
[ 0.531566] pcie_pme 0000:00:1c.4:pcie01: service driver pcie_pme loaded
[ 0.531586] pcieport 0000:00:1c.5: Signaling PME through PCIe PME interrupt
[ 0.531588] pci 0000:05:00.0: Signaling PME through PCIe PME interrupt
[ 0.531593] pcie_pme 0000:00:1c.5:pcie01: service driver pcie_pme loaded
[ 0.531615] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.531670] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 2940 ss_vid 1462 ss_did 7360
[ 0.531692] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded
[ 0.531704] pciehp 0000:00:1c.2:pcie04: HPC vendor_id 8086 device_id 2944 ss_vid 1462 ss_did 7360
[ 0.531724] pciehp 0000:00:1c.2:pcie04: service driver pciehp loaded
[ 0.531736] pciehp 0000:00:1c.4:pcie04: HPC vendor_id 8086 device_id 2948 ss_vid 1462 ss_did 7360
[ 0.531757] pciehp 0000:00:1c.4:pcie04: service driver pciehp loaded
[ 0.531770] pciehp 0000:00:1c.5:pcie04: HPC vendor_id 8086 device_id 294a ss_vid 1462 ss_did 7360
[ 0.531790] pciehp 0000:00:1c.5:pcie04: service driver pciehp loaded
[ 0.531798] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.531939] intel_idle: MWAIT substates: 0x220
[ 0.531942] intel_idle: does not run on family 6 model 15
[ 0.532050] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.532056] ACPI: Power Button [PWRB]
[ 0.532110] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.532113] ACPI: Power Button [PWRF]
[ 0.532304] ACPI: acpi_idle registered with cpuidle
[ 0.534514] ERST: Table is not found!
[ 0.534532] isapnp: Scanning for PnP cards...
[ 0.887521] isapnp: No Plug & Play device found
[ 0.887724] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.908079] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.992407] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.009544] brd: module loaded
[ 1.010239] loop: module loaded
[ 1.010450] ata_piix 0000:00:1f.2: version 2.13
[ 1.010475] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.010481] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 1.010523] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.010820] scsi0 : ata_piix
[ 1.010918] scsi1 : ata_piix
[ 1.012683] ata1: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 19
[ 1.012688] ata2: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 19
[ 1.012735] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.012749] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 1.012789] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 1.013045] scsi2 : ata_piix
[ 1.013122] scsi3 : ata_piix
[ 1.014544] ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
[ 1.014548] ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
[ 1.014610] pata_acpi 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.014640] pata_acpi 0000:04:00.0: setting latency timer to 64
[ 1.014654] pata_acpi 0000:04:00.0: PCI INT A disabled
[ 1.015012] Fixed MDIO Bus: probed
[ 1.015048] PPP generic driver version 2.4.2
[ 1.015113] tun: Universal TUN/TAP device driver, 1.6
[ 1.015115] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 1.015214] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.015217] ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
[ 1.015239] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.015255] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.015259] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.015300] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.015329] ehci_hcd 0000:00:1a.7: reset hcs_params 0x102204 dbg=1 cc=2 pcc=2 ordered !ppc ports=4
[ 1.015334] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch
[ 1.015360] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.015365] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.019248] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.019250] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[ 1.019269] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
[ 1.019274] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.023152] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[ 1.032010] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.032039] usb usb1: default language 0x0409
[ 1.032047] usb usb1: udev 1, busnum 1, minor = 0
[ 1.032049] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.032052] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.032055] usb usb1: Product: EHCI Host Controller
[ 1.032058] usb usb1: Manufacturer: Linux 2.6.37-rc1-git8t5+ ehci_hcd
[ 1.032060] usb usb1: SerialNumber: 0000:00:1a.7
[ 1.032143] usb usb1: usb_probe_device
[ 1.032146] usb usb1: configuration #1 chosen from 1 choice
[ 1.032155] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 1.032188] hub 1-0:1.0: usb_probe_interface
[ 1.032191] hub 1-0:1.0: usb_probe_interface - got id
[ 1.032194] hub 1-0:1.0: USB hub found
[ 1.032199] hub 1-0:1.0: 4 ports detected
[ 1.032201] hub 1-0:1.0: standalone hub
[ 1.032203] hub 1-0:1.0: no power switching (usb 1.0)
[ 1.032205] hub 1-0:1.0: individual port over-current protection
[ 1.032208] hub 1-0:1.0: power on to power good time: 20ms
[ 1.032213] hub 1-0:1.0: local power source is good
[ 1.032215] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 1.032308] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.032320] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.032324] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.032366] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 1.032388] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
[ 1.032393] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch
[ 1.032415] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.032420] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.036311] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.036314] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 1.036331] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
[ 1.036336] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 1.040215] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[ 1.052009] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.052030] usb usb2: default language 0x0409
[ 1.052038] usb usb2: udev 1, busnum 2, minor = 128
[ 1.052040] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.052043] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.052046] usb usb2: Product: EHCI Host Controller
[ 1.052048] usb usb2: Manufacturer: Linux 2.6.37-rc1-git8t5+ ehci_hcd
[ 1.052051] usb usb2: SerialNumber: 0000:00:1d.7
[ 1.052130] usb usb2: usb_probe_device
[ 1.052133] usb usb2: configuration #1 chosen from 1 choice
[ 1.052141] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 1.052171] hub 2-0:1.0: usb_probe_interface
[ 1.052174] hub 2-0:1.0: usb_probe_interface - got id
[ 1.052177] hub 2-0:1.0: USB hub found
[ 1.052181] hub 2-0:1.0: 8 ports detected
[ 1.052183] hub 2-0:1.0: standalone hub
[ 1.052185] hub 2-0:1.0: no power switching (usb 1.0)
[ 1.052187] hub 2-0:1.0: individual port over-current protection
[ 1.052190] hub 2-0:1.0: power on to power good time: 20ms
[ 1.052195] hub 2-0:1.0: local power source is good
[ 1.052197] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 1.052295] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.052297] ohci_hcd: block sizes: ed 64 td 64
[ 1.052321] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.052358] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.052365] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.052368] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.052409] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 1.052431] uhci_hcd 0000:00:1a.0: detected 2 ports
[ 1.052436] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.052438] uhci_hcd 0000:00:1a.0: Performing full reset
[ 1.052452] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[ 1.052467] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000bc00
[ 1.052499] usb usb3: default language 0x0409
[ 1.052506] usb usb3: udev 1, busnum 3, minor = 256
[ 1.052509] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.052512] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.052514] usb usb3: Product: UHCI Host Controller
[ 1.052516] usb usb3: Manufacturer: Linux 2.6.37-rc1-git8t5+ uhci_hcd
[ 1.052519] usb usb3: SerialNumber: 0000:00:1a.0
[ 1.052592] usb usb3: usb_probe_device
[ 1.052595] usb usb3: configuration #1 chosen from 1 choice
[ 1.052602] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 1.052633] hub 3-0:1.0: usb_probe_interface
[ 1.052635] hub 3-0:1.0: usb_probe_interface - got id
[ 1.052638] hub 3-0:1.0: USB hub found
[ 1.052642] hub 3-0:1.0: 2 ports detected
[ 1.052645] hub 3-0:1.0: standalone hub
[ 1.052646] hub 3-0:1.0: no power switching (usb 1.0)
[ 1.052649] hub 3-0:1.0: individual port over-current protection
[ 1.052651] hub 3-0:1.0: power on to power good time: 2ms
[ 1.052656] hub 3-0:1.0: local power source is good
[ 1.052658] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 1.052713] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0
[ 1.052743] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.052749] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.052753] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.052796] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 1.052816] uhci_hcd 0000:00:1a.1: detected 2 ports
[ 1.052821] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.052823] uhci_hcd 0000:00:1a.1: Performing full reset
[ 1.052836] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[ 1.052851] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
[ 1.052882] usb usb4: default language 0x0409
[ 1.052890] usb usb4: udev 1, busnum 4, minor = 384
[ 1.052893] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.052896] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.052898] usb usb4: Product: UHCI Host Controller
[ 1.052901] usb usb4: Manufacturer: Linux 2.6.37-rc1-git8t5+ uhci_hcd
[ 1.052903] usb usb4: SerialNumber: 0000:00:1a.1
[ 1.052975] usb usb4: usb_probe_device
[ 1.052978] usb usb4: configuration #1 chosen from 1 choice
[ 1.052985] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 1.053015] hub 4-0:1.0: usb_probe_interface
[ 1.053018] hub 4-0:1.0: usb_probe_interface - got id
[ 1.053020] hub 4-0:1.0: USB hub found
[ 1.053025] hub 4-0:1.0: 2 ports detected
[ 1.053027] hub 4-0:1.0: standalone hub
[ 1.053029] hub 4-0:1.0: no power switching (usb 1.0)
[ 1.053031] hub 4-0:1.0: individual port over-current protection
[ 1.053033] hub 4-0:1.0: power on to power good time: 2ms
[ 1.053038] hub 4-0:1.0: local power source is good
[ 1.053040] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 1.053094] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1
[ 1.053122] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.053128] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.053131] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.053172] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 1.053192] uhci_hcd 0000:00:1d.0: detected 2 ports
[ 1.053196] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.053199] uhci_hcd 0000:00:1d.0: Performing full reset
[ 1.053212] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 1.053218] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b800
[ 1.053247] usb usb5: default language 0x0409
[ 1.053255] usb usb5: udev 1, busnum 5, minor = 512
[ 1.053258] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.053260] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.053263] usb usb5: Product: UHCI Host Controller
[ 1.053265] usb usb5: Manufacturer: Linux 2.6.37-rc1-git8t5+ uhci_hcd
[ 1.053268] usb usb5: SerialNumber: 0000:00:1d.0
[ 1.053343] usb usb5: usb_probe_device
[ 1.053346] usb usb5: configuration #1 chosen from 1 choice
[ 1.053353] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 1.053385] hub 5-0:1.0: usb_probe_interface
[ 1.053388] hub 5-0:1.0: usb_probe_interface - got id
[ 1.053390] hub 5-0:1.0: USB hub found
[ 1.053395] hub 5-0:1.0: 2 ports detected
[ 1.053397] hub 5-0:1.0: standalone hub
[ 1.053399] hub 5-0:1.0: no power switching (usb 1.0)
[ 1.053401] hub 5-0:1.0: individual port over-current protection
[ 1.053403] hub 5-0:1.0: power on to power good time: 2ms
[ 1.053408] hub 5-0:1.0: local power source is good
[ 1.053410] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 1.053478] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0
[ 1.053497] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.053505] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.053508] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.053553] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 1.053573] uhci_hcd 0000:00:1d.1: detected 2 ports
[ 1.053577] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.053580] uhci_hcd 0000:00:1d.1: Performing full reset
[ 1.053593] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[ 1.053599] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b480
[ 1.053630] usb usb6: default language 0x0409
[ 1.053637] usb usb6: udev 1, busnum 6, minor = 640
[ 1.053640] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.053643] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.053645] usb usb6: Product: UHCI Host Controller
[ 1.053648] usb usb6: Manufacturer: Linux 2.6.37-rc1-git8t5+ uhci_hcd
[ 1.053650] usb usb6: SerialNumber: 0000:00:1d.1
[ 1.053723] usb usb6: usb_probe_device
[ 1.053726] usb usb6: configuration #1 chosen from 1 choice
[ 1.053732] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[ 1.053763] hub 6-0:1.0: usb_probe_interface
[ 1.053765] hub 6-0:1.0: usb_probe_interface - got id
[ 1.053768] hub 6-0:1.0: USB hub found
[ 1.053772] hub 6-0:1.0: 2 ports detected
[ 1.053775] hub 6-0:1.0: standalone hub
[ 1.053776] hub 6-0:1.0: no power switching (usb 1.0)
[ 1.053779] hub 6-0:1.0: individual port over-current protection
[ 1.053781] hub 6-0:1.0: power on to power good time: 2ms
[ 1.053786] hub 6-0:1.0: local power source is good
[ 1.053788] hub 6-0:1.0: trying to enable port power on non-switchable hub
[ 1.053849] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1
[ 1.053869] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.053874] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.053878] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.053918] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 1.053938] uhci_hcd 0000:00:1d.2: detected 2 ports
[ 1.053942] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.053945] uhci_hcd 0000:00:1d.2: Performing full reset
[ 1.053958] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[ 1.053964] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b400
[ 1.053995] usb usb7: default language 0x0409
[ 1.054002] usb usb7: udev 1, busnum 7, minor = 768
[ 1.054005] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.054008] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.054010] usb usb7: Product: UHCI Host Controller
[ 1.054013] usb usb7: Manufacturer: Linux 2.6.37-rc1-git8t5+ uhci_hcd
[ 1.054015] usb usb7: SerialNumber: 0000:00:1d.2
[ 1.054092] usb usb7: usb_probe_device
[ 1.054095] usb usb7: configuration #1 chosen from 1 choice
[ 1.054102] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[ 1.054134] hub 7-0:1.0: usb_probe_interface
[ 1.054136] hub 7-0:1.0: usb_probe_interface - got id
[ 1.054139] hub 7-0:1.0: USB hub found
[ 1.054143] hub 7-0:1.0: 2 ports detected
[ 1.054145] hub 7-0:1.0: standalone hub
[ 1.054147] hub 7-0:1.0: no power switching (usb 1.0)
[ 1.054149] hub 7-0:1.0: individual port over-current protection
[ 1.054152] hub 7-0:1.0: power on to power good time: 2ms
[ 1.054156] hub 7-0:1.0: local power source is good
[ 1.054158] hub 7-0:1.0: trying to enable port power on non-switchable hub
[ 1.054219] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2
[ 1.054238] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 1.054244] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.054248] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.054288] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8
[ 1.054307] uhci_hcd 0000:00:1d.3: detected 2 ports
[ 1.054311] uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
[ 1.054314] uhci_hcd 0000:00:1d.3: Performing full reset
[ 1.054327] uhci_hcd 0000:00:1d.3: supports USB remote wakeup
[ 1.054333] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000b080
[ 1.054363] usb usb8: default language 0x0409
[ 1.054371] usb usb8: udev 1, busnum 8, minor = 896
[ 1.054374] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.054376] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.054379] usb usb8: Product: UHCI Host Controller
[ 1.054381] usb usb8: Manufacturer: Linux 2.6.37-rc1-git8t5+ uhci_hcd
[ 1.054384] usb usb8: SerialNumber: 0000:00:1d.3
[ 1.054455] usb usb8: usb_probe_device
[ 1.054458] usb usb8: configuration #1 chosen from 1 choice
[ 1.054465] usb usb8: adding 8-0:1.0 (config #1, interface 0)
[ 1.054497] hub 8-0:1.0: usb_probe_interface
[ 1.054499] hub 8-0:1.0: usb_probe_interface - got id
[ 1.054502] hub 8-0:1.0: USB hub found
[ 1.054506] hub 8-0:1.0: 2 ports detected
[ 1.054509] hub 8-0:1.0: standalone hub
[ 1.054510] hub 8-0:1.0: no power switching (usb 1.0)
[ 1.054513] hub 8-0:1.0: individual port over-current protection
[ 1.054515] hub 8-0:1.0: power on to power good time: 2ms
[ 1.054520] hub 8-0:1.0: local power source is good
[ 1.054522] hub 8-0:1.0: trying to enable port power on non-switchable hub
[ 1.054582] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.3
[ 1.054704] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.057251] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.057257] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.057342] mice: PS/2 mouse device common for all mice
[ 1.057482] rtc_cmos 00:03: RTC can wake from S4
[ 1.057551] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.057575] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.057705] device-mapper: uevent: version 1.0.3
[ 1.057831] device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@xxxxxxxxxx
[ 1.057881] device-mapper: multipath: version 1.1.1 loaded
[ 1.057884] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.058016] EISA: Probing bus 0 at eisa.0
[ 1.058018] EISA: Cannot allocate resource for mainboard
[ 1.058021] Cannot allocate resource for EISA slot 1
[ 1.058023] Cannot allocate resource for EISA slot 2
[ 1.058025] Cannot allocate resource for EISA slot 3
[ 1.058028] Cannot allocate resource for EISA slot 4
[ 1.058030] Cannot allocate resource for EISA slot 5
[ 1.058032] Cannot allocate resource for EISA slot 6
[ 1.058034] Cannot allocate resource for EISA slot 7
[ 1.058036] Cannot allocate resource for EISA slot 8
[ 1.058038] EISA: Detected 0 cards.
[ 1.058086] cpuidle: using governor ladder
[ 1.058088] cpuidle: using governor menu
[ 1.058419] TCP cubic registered
[ 1.058596] NET: Registered protocol family 10
[ 1.059017] lo: Disabled Privacy Extensions
[ 1.059270] NET: Registered protocol family 17
[ 1.059290] Registering the dns_resolver key type
[ 1.059818] Using IPI No-Shortcut mode
[ 1.059926] PM: Hibernation image not present or could not be loaded.
[ 1.059938] registered taskstats version 1
[ 1.060328] Magic number: 2:69:102
[ 1.060407] rtc_cmos 00:03: setting system clock to 2010-11-13 00:07:01 UTC (1289606821)
[ 1.060410] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.060412] EDD information not available.
[ 1.082027] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.132031] hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 1.152046] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.152053] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
[ 1.152058] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.152062] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.152067] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.152071] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.152075] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.342668] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.353297] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.488041] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.496040] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.496332] ata1.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7
[ 1.496335] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.504118] ata2.00: ATAPI: PIONEER DVD-RW DVR-212D, 1.24, max UDMA/66
[ 1.504347] ata1.00: configured for UDMA/133
[ 1.504472] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5
[ 1.504632] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.504647] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.504694] sd 0:0:0:0: [sda] Write Protect is off
[ 1.504697] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.504723] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.520119] ata2.00: configured for UDMA/66
[ 1.526061] scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-212D 1.24 PQ: 0 ANSI: 5
[ 1.549679] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 1.549682] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.549790] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.549858] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.564523] sda: sda1 sda2 < sda5 sda6 >
[ 1.564860] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.564878] Freeing unused kernel memory: 680k freed
[ 1.583892] udev[72]: starting version 163
[ 1.695553] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.695578] r8169 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.695620] r8169 0000:05:00.0: setting latency timer to 64
[ 1.695693] r8169 0000:05:00.0: irq 45 for MSI/MSI-X
[ 1.699984] r8169 0000:05:00.0: eth0: RTL8168b/8111b at 0xf8026000, 00:1d:92:33:07:c1, XID 18000000 IRQ 45
[ 1.710964] ahci 0000:04:00.0: version 3.0
[ 1.712611] pata_marvell 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.712648] pata_marvell 0000:04:00.0: setting latency timer to 64
[ 1.713067] scsi4 : pata_marvell
[ 1.713145] scsi5 : pata_marvell
[ 1.713204] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 16
[ 1.713207] ata6: PATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 16
[ 1.972307] EXT4-fs (sda5): INFO: recovery required on readonly filesystem
[ 1.972313] EXT4-fs (sda5): write access will be enabled during recovery
[ 2.136019] usb usb4: suspend_rh (auto-stop)
[ 2.136023] usb usb3: suspend_rh (auto-stop)
[ 2.136051] usb usb5: suspend_rh (auto-stop)
[ 2.136053] usb usb6: suspend_rh (auto-stop)
[ 2.136079] usb usb8: suspend_rh (auto-stop)
[ 2.136081] usb usb7: suspend_rh (auto-stop)
[ 3.808029] hub 3-0:1.0: hub_suspend
[ 3.808040] usb usb3: bus auto-suspend
[ 3.808043] usb usb3: suspend_rh
[ 3.808060] hub 2-0:1.0: hub_suspend
[ 3.808064] usb usb2: bus auto-suspend
[ 3.808067] ehci_hcd 0000:00:1d.7: suspend root hub
[ 3.808090] hub 5-0:1.0: hub_suspend
[ 3.808093] usb usb5: bus auto-suspend
[ 3.808096] usb usb5: suspend_rh
[ 3.808110] hub 4-0:1.0: hub_suspend
[ 3.808114] usb usb4: bus auto-suspend
[ 3.808116] usb usb4: suspend_rh
[ 3.808130] hub 7-0:1.0: hub_suspend
[ 3.808134] usb usb7: bus auto-suspend
[ 3.808136] usb usb7: suspend_rh
[ 3.808150] hub 6-0:1.0: hub_suspend
[ 3.808154] usb usb6: bus auto-suspend
[ 3.808156] usb usb6: suspend_rh
[ 3.808171] hub 8-0:1.0: hub_suspend
[ 3.808174] usb usb8: bus auto-suspend
[ 3.808177] usb usb8: suspend_rh
[ 3.824040] hub 1-0:1.0: hub_suspend
[ 3.824046] usb usb1: bus auto-suspend
[ 3.824049] ehci_hcd 0000:00:1a.7: suspend root hub
[ 5.119764] EXT4-fs (sda5): recovery complete
[ 5.120206] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 6.820260] Adding 6037500k swap on /dev/sda6. Priority:-1 extents:1 across:6037500k
[ 7.973019] udev[274]: starting version 163
[ 8.161352] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
[ 8.666687] Linux agpgart interface v0.103
[ 8.705697] lp: driver loaded but no devices found
[ 9.048121] psmouse serio1: ID: 10 00 64
[ 9.246222] [drm] Initialized drm 1.1.0 20060810
[ 9.438176] Linux video capture interface: v2.00
[ 9.564821] cx23885 driver version 0.0.2 loaded
[ 9.565054] cx23885 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 9.565295] CORE cx23885[0]: subsystem: 107d:6f21, board: LEADTEK WinFast PxPVR2200 [card=29,autodetected]
[ 9.612597] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input3
[ 9.626158] apparmor_parser[499]: segfault at 0 ip 08051034 sp bf908550 error 4 in apparmor_parser[8048000+be000]
[ 9.627497] apparmor_parser[530]: segfault at 0 ip 08051034 sp bfbe7270 error 4 in apparmor_parser[8048000+be000]
[ 9.760922] IR NEC protocol handler initialized
[ 10.028798] IR RC5(x) protocol handler initialized
[ 10.033114] cx25840 2-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[ 10.130781] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.130789] nouveau 0000:01:00.0: setting latency timer to 64
[ 10.134099] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x092880a2)
[ 10.137778] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
[ 10.193162] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 10.193167] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 10.193171] [drm] nouveau 0000:01:00.0: Bios version 62.92.1f.00
[ 10.193175] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[ 10.193178] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 4.0
[ 10.193182] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 02000300 00000028
[ 10.193185] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 01000302 00000030
[ 10.193188] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 04011310 00000028
[ 10.193191] [drm] nouveau 0000:01:00.0: Raw DCB entry 3: 02011312 00000030
[ 10.193193] [drm] nouveau 0000:01:00.0: Raw DCB entry 4: 010223f1 00c0c080
[ 10.193197] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 16 4
[ 10.193201] [drm] nouveau 0000:01:00.0: 0: 0x00001030: type 0x30 idx 0 tag 0x07
[ 10.193204] [drm] nouveau 0000:01:00.0: 1: 0x00002130: type 0x30 idx 1 tag 0x08
[ 10.193207] [drm] nouveau 0000:01:00.0: 2: 0x00000210: type 0x10 idx 2 tag 0xff
[ 10.193210] [drm] nouveau 0000:01:00.0: 3: 0x00000211: type 0x11 idx 3 tag 0xff
[ 10.193213] [drm] nouveau 0000:01:00.0: 4: 0x00000213: type 0x13 idx 4 tag 0xff
[ 10.193218] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xC10F
[ 10.236231] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xC4B3
[ 10.252007] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xD22E
[ 10.252015] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xD350
[ 10.260074] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xD580
[ 10.260077] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xD5E5
[ 10.284012] [drm] nouveau 0000:01:00.0: 0xD5E5: Condition still not met after 20ms, skipping following opcodes
[ 10.377111] IR RC6 protocol handler initialized
[ 10.486636] IR JVC protocol handler initialized
[ 10.561858] adt7475 3-002e: ADT7473 device, revision 1
[ 10.573331] [drm] nouveau 0000:01:00.0: Detected monitoring device: adt7473
[ 10.575771] [drm] nouveau 0000:01:00.0: 1 available performance level(s)
[ 10.575777] [drm] nouveau 0000:01:00.0: 3: memory 900MHz core 600MHz shader 1500MHz fanspeed 100%
[ 10.575793] [drm] nouveau 0000:01:00.0: c: memory 399MHz core 399MHz shader 810MHz voltage 1050mV
[ 10.575939] [drm] nouveau 0000:01:00.0: Detected 512MiB VRAM
[ 10.575987] [TTM] Zone kernel: Available graphics memory: 436952 kiB.
[ 10.575989] [TTM] Zone highmem: Available graphics memory: 1030716 kiB.
[ 10.575991] [TTM] Initializing pool allocator.
[ 10.623987] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 10.627632] [drm] nouveau 0000:01:00.0: DCB encoder 1 unknown
[ 10.627636] [drm] nouveau 0000:01:00.0: TV-1 has no encoders, removing
[ 10.649828] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
[ 10.656536] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 1
[ 10.815994] [drm] nouveau 0000:01:00.0: allocated 1680x1050 fb: 0x40280000, bo ed720600
[ 10.820059] Console: switching to colour frame buffer device 210x65
[ 10.822142] fb0: nouveaufb frame buffer device
[ 10.822144] drm: registered panic notifier
[ 10.822160] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0
[ 10.892923] IR Sony protocol handler initialized
[ 10.966197] cx25840 2-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
[ 11.128789] lirc_dev: IR Remote Control driver registered, major 251
[ 11.189287] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 11.189354] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 11.189569] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 11.195213] tuner 1-0061: chip found @ 0xc2 (cx23885[0])
[ 11.204494] IR LIRC bridge handler initialized
[ 11.493273] hda_codec: ALC888: BIOS auto-probing.
[ 11.498133] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
[ 11.582258] xc2028 1-0061: creating new instance
[ 11.582262] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
[ 11.582385] cx23885[0]/0: registered device video0 [v4l2]
[ 11.586413] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 11.590502] cx23885[0]: registered device video1 [mpeg]
[ 11.590506] cx23885_dev_checkrevision() Hardware revision = 0xb0
[ 11.590515] cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 18, latency: 0, mmio: 0xfe800000
[ 11.590523] cx23885 0000:03:00.0: setting latency timer to 64
[ 11.590609] cx23885 0000:03:00.0: irq 47 for MSI/MSI-X
[ 12.805853] apparmor_parser[663]: segfault at 0 ip 08051034 sp bffbae50 error 4 in apparmor_parser[8048000+be000]
[ 15.146813] apparmor_parser[764]: segfault at 0 ip 08051034 sp bfe3f510 error 4
[ 15.146819] apparmor_parser[763]: segfault at 0 ip 08051034 sp bfc0f950 error 4 in apparmor_parser[8048000+be000] in apparmor_parser[8048000+be000]
[ 15.146828]
[ 15.948489] r8169 0000:05:00.0: eth0: link up
[ 15.948496] r8169 0000:05:00.0: eth0: link up
[ 16.080716] ppdev: user-space parallel port driver
[ 19.983252] [drm] nouveau 0000:01:00.0: Allocating FIFO number 2
[ 19.989423] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 2
[ 25.288925] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0
[ 26.648008] eth0: no IPv6 routers present
[ 27.617088] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 27.622697] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 27.721944] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 29.287649] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0
[ 191.633234] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 191.634557] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.154265] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.224243] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.281708] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.327158] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.371668] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.416130] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.464672] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.513003] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.561468] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.609827] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.658371] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.706817] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.755261] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.803696] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.852216] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.903666] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.953158] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 378.998956] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.043335] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.087938] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.131470] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.175547] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.219734] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.263801] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.315179] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.359928] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.403984] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.448103] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.496288] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.544277] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.592419] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.640532] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.688642] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.736684] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.784785] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.832824] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.880871] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.928940] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 379.977051] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.025092] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.073203] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.121268] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.169385] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.217472] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.265511] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.313609] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.361703] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.409760] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.457850] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.505972] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.554060] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.602100] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.650223] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.698285] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.746374] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.794518] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.842535] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.890855] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.938758] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 380.986820] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.034929] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.082984] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.127974] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.175123] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.223237] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.271351] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.319427] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.367454] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.415533] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.463695] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.511755] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.559809] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.607885] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.655953] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.704072] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.756216] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.808322] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.860029] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.912395] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 381.964538] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.016565] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.068682] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.120751] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.172814] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.226572] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.277043] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.329434] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.381149] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.433234] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.485338] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.537385] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.589539] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.641515] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.693742] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.745804] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.797789] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.849875] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.902044] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 382.954169] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.006155] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.057723] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.110290] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.162386] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.212606] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.266587] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.318542] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.370714] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.422793] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.474540] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.525742] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.578992] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.630539] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.680605] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.735315] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.786535] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.838841] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.891574] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.942578] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 383.990545] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.043787] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.092243] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.146582] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.200017] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.254579] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.307153] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.360290] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.416349] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.470583] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.523453] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.576541] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.632747] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.686578] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.739507] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.792858] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.849002] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.902579] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 384.955445] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 385.009225] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 385.065389] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 385.118577] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 437.172463] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 437.177662] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 437.180323] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 538.893804] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 538.895130] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 614.641060] xc2028 1-0061: xc2028/3028 firmware name not set!
[ 738.677382] lo: Disabled Privacy Extensions
[ 746.255918] exe (2157): /proc/2157/oom_adj is deprecated, please use /proc/2157/oom_score_adj instead.
