Re: [PATCH v2 8/9] media: dt-bindings: Add Intel Displayport RX IP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Feb 28, 2024 at 1:18 PM Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
>
> On 28/02/2024 12:05, Paweł Anikiel wrote:
> > On Tue, Feb 27, 2024 at 3:29 PM Rob Herring <robh@xxxxxxxxxx> wrote:
> >>
> >> On Mon, Feb 26, 2024 at 11:59:42AM +0100, Paweł Anikiel wrote:
> >>> On Mon, Feb 26, 2024 at 10:13 AM Krzysztof Kozlowski
> >>> <krzysztof.kozlowski@xxxxxxxxxx> wrote:
> >>>>
> >>>> On 21/02/2024 17:02, Paweł Anikiel wrote:
> >>>>> The Intel Displayport RX IP is a part of the DisplayPort Intel FPGA IP
> >>>>> Core. It implements a DisplayPort 1.4 receiver capable of HBR3 video
> >>>>> capture and Multi-Stream Transport. The user guide can be found here:
> >>>>>
> >>>>> https://www.intel.com/programmable/technical-pdfs/683273.pdf
> >>>>>
> >>>>> Signed-off-by: Paweł Anikiel <panikiel@xxxxxxxxxx>
> >>>>> ---
> >>>>>  .../devicetree/bindings/media/intel,dprx.yaml | 160 ++++++++++++++++++
> >>>>>  1 file changed, 160 insertions(+)
> >>>>>  create mode 100644 Documentation/devicetree/bindings/media/intel,dprx.yaml
> >>>>>
> >>>>> diff --git a/Documentation/devicetree/bindings/media/intel,dprx.yaml b/Documentation/devicetree/bindings/media/intel,dprx.yaml
> >>>>> new file mode 100644
> >>>>> index 000000000000..31025f2d5dcd
> >>>>> --- /dev/null
> >>>>> +++ b/Documentation/devicetree/bindings/media/intel,dprx.yaml
> >>>>> @@ -0,0 +1,160 @@
> >>>>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> >>>>> +%YAML 1.2
> >>>>> +---
> >>>>> +$id: http://devicetree.org/schemas/media/intel,dprx.yaml#
> >>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >>>>> +
> >>>>> +title: Intel DisplayPort RX IP
> >>>>> +
> >>>>> +maintainers:
> >>>>> +  - Paweł Anikiel <panikiel@xxxxxxxxxx>
> >>>>> +
> >>>>> +description: |
> >>>>> +  The Intel Displayport RX IP is a part of the DisplayPort Intel FPGA IP
> >>>>> +  Core. It implements a DisplayPort 1.4 receiver capable of HBR3 video
> >>>>> +  capture and Multi-Stream Transport.
> >>>>> +
> >>>>> +  The IP features a large number of configuration parameters, found at:
> >>>>> +  https://www.intel.com/content/www/us/en/docs/programmable/683273/23-3-20-0-1/sink-parameters.html
> >>>>> +
> >>>>> +  The following parameters have to be enabled:
> >>>>> +    - Support DisplayPort sink
> >>>>> +    - Enable GPU control
> >>>>> +  The following parameters' values have to be set in the devicetree:
> >>>>> +    - RX maximum link rate
> >>>>> +    - Maximum lane count
> >>>>> +    - Support MST
> >>>>> +    - Max stream count (only if Support MST is enabled)
> >>>>> +
> >>>>> +properties:
> >>>>> +  compatible:
> >>>>> +    const: intel,dprx-20.0.1
> >>>>> +
> >>>>> +  reg:
> >>>>> +    maxItems: 1
> >>>>> +
> >>>>> +  interrupts:
> >>>>> +    maxItems: 1
> >>>>> +
> >>>>> +  intel,max-link-rate:
> >>>>> +    $ref: /schemas/types.yaml#/definitions/uint32
> >>>>> +    description: Max link rate configuration parameter
> >>>>
> >>>> Please do not duplicate property name in description. It's useless.
> >>>> Instead explain what is this responsible for.
> >>>>
> >>>> Why max-link-rate would differ for the same dprx-20.0.1? And why
> >>>> standard properties cannot be used?
> >>>>
> >>>> Same for all questions below.
> >>>
> >>> These four properties are the IP configuration parameters mentioned in
> >>> the device description. When generating the IP core you can set these
> >>> parameters, which could make them differ for the same dprx-20.0.1.
> >>> They are documented in the user guide, for which I also put a link in
> >>> the description. Is that enough? Or should I also document these
> >>> parameters here?
> >>
> >> Use the standard properties: link-frequencies and data-lanes. Those go
> >> under the port(s) because they are inheritly per logical link.
> >
> > The DP receiver has one input interface (a deserialized DP stream),
> > and up to four output interfaces (the decoded video streams). The "max
> > link rate" and "max lane count" parameters only describe the input
> > interface to the receiver. However, the port(s) I am using here are
> > for the output streams. They are not affected by those parameters, so
> > I don't think these properties should go under the output port(s).
> >
> > The receiver doesn't have an input port in the DT, because there isn't
> > any controllable entity on the other side - the deserializer doesn't
> > have any software interface. Since these standard properties
> > (link-frequencies and data-lanes) are only defined in
> > video-interfaces.yaml (which IIUC describes a graph endpoint), I can't
> > use them directly in the device node.
>
> DT describes the hardware, so where does the input come? From something,
> right? Regardless if you have a driver or not. There is dp-connector
> binding, if this is physical port.

Yes, it is a physical port. I agree adding a DT node for the physical
DP input connector would let us add link-frequencies to the input port
of the receiver.

However, dp-connector seems to be a binding for an output port - it's
under schemas/display/connector, and DP_PWR can be a power supply only
for an output port (looking at the dp-pwr-supply property). Also, the
driver for this binding is a DRM bridge driver (display-connector.c)
which would not be compatible with a v4l2 (sub)device.





[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux