Hi Jacopo, On Thu, Dec 07, 2023 at 11:13:21AM +0100, Jacopo Mondi wrote: > Hi Sakari > > On Thu, Dec 07, 2023 at 09:57:06AM +0000, Sakari Ailus wrote: > > Hi Jacopo, > > > > On Wed, Dec 06, 2023 at 04:58:59PM +0100, Jacopo Mondi wrote: > > > Add bindings for OmniVision OV64A40. > > > > > > Co-developed-by: Lee Jackson <lee.jackson@xxxxxxxxxxx> > > > Signed-off-by: Jacopo Mondi <jacopo.mondi@xxxxxxxxxxxxxxxx> > > > Acked-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx> > > > --- > > > .../bindings/media/i2c/ovti,ov64a40.yaml | 97 +++++++++++++++++++ > > > 1 file changed, 97 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml > > > new file mode 100644 > > > index 000000000000..e6c9d540a2dd > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov64a40.yaml > > > @@ -0,0 +1,97 @@ > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov64a40.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: OmniVision OV64A40 Image Sensor > > > + > > > +maintainers: > > > + - Jacopo Mondi <jacopo.mondi@xxxxxxxxxxxxxxxx> > > > + > > > +allOf: > > > + - $ref: /schemas/media/video-interface-devices.yaml# > > > + > > > +properties: > > > + compatible: > > > + const: ovti,ov64a40 > > > + > > > + reg: > > > + maxItems: 1 > > > + > > > + clocks: > > > + maxItems: 1 > > > + > > > + avdd-supply: > > > + description: Analog voltage supply, 2.8 volts > > > + > > > + dvdd-supply: > > > + description: Digital core voltage supply, 1.1 volts > > > + > > > + dovdd-supply: > > > + description: Digital I/O voltage supply, 1.8 volts > > > + > > > + powerdown-gpios: > > > + maxItems: 1 > > > + > > > + reset-gpios: > > > + maxItems: 1 > > > + > > > + port: > > > + $ref: /schemas/graph.yaml#/$defs/port-base > > > + additionalProperties: false > > > + > > > + properties: > > > + endpoint: > > > + $ref: /schemas/media/video-interfaces.yaml# > > > + additionalProperties: false > > > + > > > + properties: > > > + bus-type: > > > + enum: > > > + - 1 # MIPI CSI-2 C-PHY > > > + - 4 # MIPI CSI-2 D-PHY > > > + data-lanes: true > > > + link-frequencies: true > > > + clock-noncontinuous: true > > > + remote-endpoint: true > > > + > > > +required: > > > + - compatible > > > + - reg > > > + - clocks > > > + - port > > > + > > > +unevaluatedProperties: false > > > + > > > +examples: > > > + - | > > > + #include <dt-bindings/gpio/gpio.h> > > > + > > > + i2c { > > > + #address-cells = <1>; > > > + #size-cells = <0>; > > > + > > > + camera@36 { > > > + compatible = "ovti,ov64a40"; > > > + reg = <0x36>; > > > + clocks = <&camera_clk>; > > > + dovdd-supply = <&vgen4_reg>; > > > + avdd-supply = <&vgen3_reg>; > > > + dvdd-supply = <&vgen2_reg>; > > > + powerdown-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; > > > + reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; > > > + rotation = <180>; > > > + orientation = <2>; > > > + > > > + port { > > > + endpoint { > > > + remote-endpoint = <&mipi_csi2_in>; > > > + bus-type = <4>; > > > + data-lanes = <1 2 3 4>; > > > > This is missing link-frequencies. > > > > I was not sure about this, in facts. > > Bindings are about HW while link-frequencies is only about restricting > how the driver configures the sensor. Thus, I've not listed it as > mandatory however the driver mandates its presence. > > Should I make it mandatory in bindings ? See <URL:https://hverkuil.home.xs4all.nl/spec/driver-api/camera-sensor.html#handling-clocks>. IOW it's about the driver, too, but only secondarily. > > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > +... > > -- Regards, Sakari Ailus
