Hi Laurent, Thank you for the patchset any my apologies for not reviewing it earlier. On Tue, Oct 17, 2023 at 04:21:01PM +0300, Laurent Pinchart wrote: > From: Paul Elder <paul.elder@xxxxxxxxxxxxxxxx> > > The THP7312 is an external ISP from THine. Add DT bindings for it. > > Signed-off-by: Paul Elder <paul.elder@xxxxxxxxxxxxxxxx> > Co-developed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > --- > Changes since v2: > > - Drop description of reg property > - Improve thine,boot-mode property documentation > - Making thine,boot-mode property optional > - Don't use underscores in supplies names > --- > .../bindings/media/i2c/thine,thp7312.yaml | 226 ++++++++++++++++++ > MAINTAINERS | 7 + > 2 files changed, 233 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml > > diff --git a/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml > new file mode 100644 > index 000000000000..0758d8d44826 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml > @@ -0,0 +1,226 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright (c) 2023 Ideas on Board > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/i2c/thine,thp7312.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: THine THP7312 > + > +maintainers: > + - Paul Elder <paul.elder@@ideasonboard.com> > + > +description: > + The THP7312 is a standalone ISP controlled over i2c, and is capable of > + various image processing and correction functions, including 3A control. It > + can be connected to CMOS image sensors from various vendors, supporting both > + MIPI CSI-2 and parallel interfaces. It can also output on either MIPI CSI-2 > + or parallel. The hardware is capable of transmitting and receiving MIPI > + interlaved data strams with data types or multiple virtual channel > + identifiers. > + > +allOf: > + - $ref: ../video-interface-devices.yaml# > + > +properties: > + compatible: > + const: thine,thp7312 > + > + reg: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + description: CLKI clock input > + > + thine,boot-mode: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 1 > + default: 1 > + description: > + Boot mode of the THP7312, reflecting the value of the BOOT[0] pin strap. > + 0 is for the SPI/2-wire slave boot, 1 is for the SPI master boot (from > + external flash ROM). > + > + reset-gpios: > + maxItems: 1 > + description: > + Reference to the GPIO connected to the RESET_N pin, if any. > + Must be released (set high) after all supplies are applied. > + > + vddcore-supply: > + description: > + 1.2V supply for core, PLL, MIPI rx and MIPI tx. > + > + vhtermrx-supply: > + description: > + Supply for input (RX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel. > + > + vddtx-supply: > + description: > + Supply for output (TX). 1.8V for MIPI, or 1.8/2.8/3.3V for parallel. > + > + vddhost-supply: > + description: > + Supply for host interface. 1.8V, 2.8V, or 3.3V. > + > + vddcmos-supply: > + description: > + Supply for sensor interface. 1.8V, 2.8V, or 3.3V. > + > + vddgpio-0-supply: > + description: > + Supply for GPIO_0. 1.8V, 2.8V, or 3.3V. > + > + vddgpio-1-supply: > + description: > + Supply for GPIO_1. 1.8V, 2.8V, or 3.3V. > + > + orientation: true > + rotation: true > + > + port: > + $ref: /schemas/graph.yaml#/$defs/port-base > + additionalProperties: false > + > + properties: > + endpoint: > + $ref: /schemas/media/video-interfaces.yaml# > + unevaluatedProperties: false > + > + properties: > + data-lanes: > + description: > + This property is for lane reordering between the THP7312 and the > + SoC. The sensor supports either two-lane, or four-lane operation. > + If this property is omitted four-lane operation is assumed. For > + two-lane operation the property must be set to <1 2>. How are link frequencies determined by the device? The description above also says the parallel interface is supported. The bindings do not reflect that however. Same for the sensor node below. Is the intention to add support for these later on? In that case you'll need bus-type and default that to CSI-2 for DTs conforming to these bindings. > + minItems: 2 > + maxItems: 4 > + items: > + maximum: 4 > + > + sensors: > + type: object > + description: List of connected sensors > + > + properties: > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 0 > + > + patternProperties: > + "^sensor@[01]": > + type: object > + description: > + Sensors connected to the first and second input, with one node per > + sensor. > + > + properties: > + thine,model: > + $ref: /schemas/types.yaml#/definitions/string > + description: > + Model of the connected sensors. Must be a valid compatible string. > + > + reg: > + maxItems: 1 > + description: THP7312 input port number > + > + data-lanes: > + $ref: /schemas/media/video-interfaces.yaml#/properties/data-lanes > + items: > + maxItems: 4 > + description: > + This property is for lane reordering between the THP7312 and the imaging > + sensor that it is connected to. > + > + patternProperties: > + ".*-supply": > + description: Power supplies for the sensor > + > + required: > + - reg > + - data-lanes > + > + additionalProperties: false > + > + required: > + - "#address-cells" > + - "#size-cells" > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - reset-gpios > + - clocks > + - vddcore-supply > + - vhtermrx-supply > + - vddtx-supply > + - vddhost-supply > + - vddcmos-supply > + - vddgpio-0-supply > + - vddgpio-1-supply > + - sensors > + - port > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + camera@61 { > + compatible = "thine,thp7312"; > + reg = <0x61>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cam1_pins_default>; > + > + reset-gpios = <&pio 119 GPIO_ACTIVE_LOW>; > + clocks = <&camera61_clk>; > + > + vddcore-supply = <&vsys_v4p2>; > + vhtermrx-supply = <&vsys_v4p2>; > + vddtx-supply = <&vsys_v4p2>; > + vddhost-supply = <&vsys_v4p2>; > + vddcmos-supply = <&vsys_v4p2>; > + vddgpio-0-supply = <&vsys_v4p2>; > + vddgpio-1-supply = <&vsys_v4p2>; > + > + orientation = <0>; > + rotation = <0>; > + > + sensors { > + #address-cells = <1>; > + #size-cells = <0>; > + > + sensor@0 { > + thine,model = "sony,imx258"; > + reg = <0>; > + > + data-lanes = <4 1 3 2>; Does the device support lane mapping? > + > + dovdd-supply = <&vsys_v4p2>; > + avdd-supply = <&vsys_v4p2>; > + dvdd-supply = <&vsys_v4p2>; > + }; > + }; > + > + port { > + thp7312_2_endpoint: endpoint { > + remote-endpoint = <&mipi_thp7312_2>; > + data-lanes = <4 2 1 3>; > + }; > + }; > + }; > + }; > +... > diff --git a/MAINTAINERS b/MAINTAINERS > index 3b47e0b56859..7451367e6780 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -21448,6 +21448,13 @@ S: Maintained > F: Documentation/ABI/testing/sysfs-class-firmware-attributes > F: drivers/platform/x86/think-lmi.? > > +THP7312 ISP DRIVER > +M: Paul Elder <paul.elder@xxxxxxxxxxxxxxxx> > +L: linux-media@xxxxxxxxxxxxxxx > +S: Maintained > +T: git git://linuxtv.org/media_tree.git > +F: Documentation/devicetree/bindings/media/i2c/thine,thp7312.yaml > + > THUNDERBOLT DMA TRAFFIC TEST DRIVER > M: Isaac Hazan <isaac.hazan@xxxxxxxxx> > L: linux-usb@xxxxxxxxxxxxxxx -- Regards, Sakari Ailus
