On 28/09/2023 10:22, Hans Verkuil wrote:
> On 28/09/2023 10:12, Jack Zhu wrote:
>>
>>
>> On 2023/9/15 17:26, Hans Verkuil wrote:
>>> On 14/09/2023 05:15, Jack Zhu wrote:
>>>> Hi,
>>>>
>>>> This series is the v9 series that attempts to support the Camera Subsystem
>>>> found on StarFive JH7110 SoC.
>>>>
>>>> This series is based on top of the master branch of media_stage repository.
>>>>
>>>> The following are the media graph for the device and the v4l2-compliance
>>>> output.
>>>>
>>>> ===========================================================================
>>>> [the media graph]:
>>>>
>>>> digraph board {
>>>> rankdir=TB
>>>> n00000001 [label="{{<port0> 0} | stf_isp\n/dev/v4l-subdev0 | {<port1> 1}}", shape=Mrecord, style=filled, fillcolor=green]
>>>> n00000001:port1 -> n00000008 [style=dashed]
>>>> n00000004 [label="capture_raw\n/dev/video0", shape=box, style=filled, fillcolor=yellow]
>>>> n00000008 [label="capture_yuv\n/dev/video1", shape=box, style=filled, fillcolor=yellow]
>>>> n0000000e [label="{{<port0> 0} | cdns_csi2rx.19800000.csi-bridge\n | {<port1> 1 | <port2> 2 | <port3> 3 | <port4> 4}}", shape=Mrecord, style=filled, fillcolor=green]
>>>> n0000000e:port1 -> n00000001:port0 [style=dashed]
>>>> n0000000e:port1 -> n00000004 [style=dashed]
>>>> n00000018 [label="{{} | imx219 6-0010\n/dev/v4l-subdev1 | {<port0> 0}}", shape=Mrecord, style=filled, fillcolor=green]
>>>> n00000018:port0 -> n0000000e:port0 [style=bold]
>>>> }
>>>>
>>>> [the device topology]:
>>>>
>>>> Media controller API version 6.5.0
>>>>
>>>> Media device information
>>>> ------------------------
>>>> driver starfive-camss
>>>> model Starfive Camera Subsystem
>>>> serial
>>>> bus info platform:19840000.camss
>>>> hw revision 0x0
>>>> driver version 6.5.0
>>>>
>>>> Device topology
>>>> - entity 1: stf_isp (2 pads, 2 links)
>>>> type V4L2 subdev subtype Unknown flags 0
>>>> device node name /dev/v4l-subdev0
>>>> pad0: Sink
>>>> [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb
>>>> crop.bounds:(0,0)/1920x1080
>>>> crop:(0,0)/1920x1080]
>>>> <- "cdns_csi2rx.19800000.csi-bridge":1 []
>>>> pad1: Source
>>>> [fmt:YUYV8_1_5X8/1920x1080 field:none colorspace:srgb
>>>> crop.bounds:(0,0)/1920x1080
>>>> crop:(0,0)/1920x1080]
>>>> -> "capture_yuv":0 []
>>>>
>>>> - entity 4: capture_raw (1 pad, 1 link)
>>>> type Node subtype V4L flags 0
>>>> device node name /dev/video0
>>>> pad0: Sink
>>>> <- "cdns_csi2rx.19800000.csi-bridge":1 []
>>>>
>>>> - entity 8: capture_yuv (1 pad, 1 link)
>>>> type Node subtype V4L flags 0
>>>> device node name /dev/video1
>>>> pad0: Sink
>>>> <- "stf_isp":1 []
>>>>
>>>> - entity 14: cdns_csi2rx.19800000.csi-bridge (5 pads, 3 links)
>>>> type V4L2 subdev subtype Unknown flags 0
>>>> pad0: Sink
>>>> <- "imx219 6-0010":0 [ENABLED,IMMUTABLE]
>>>> pad1: Source
>>>> -> "stf_isp":0 []
>>>> -> "capture_raw":0 []
>>>> pad2: Source
>>>> pad3: Source
>>>> pad4: Source
>>>>
>>>> - entity 24: imx219 6-0010 (1 pad, 1 link)
>>>> type V4L2 subdev subtype Sensor flags 0
>>>> device node name /dev/v4l-subdev1
>>>> pad0: Source
>>>> [fmt:SRGGB10_1X10/3280x2464 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range
>>>> crop.bounds:(8,8)/3280x2464
>>>> crop:(8,8)/3280x2464]
>>>> -> "cdns_csi2rx.19800000.csi-bridge":0 [ENABLED,IMMUTABLE]
>>>>
>>>> ===========================================================================
>>>> [the v4l2-compliance output]:
>>>>
>>>> v4l2-compliance 1.24.1, 64 bits, 64-bit time_t
>>>
>>> This v4l2-compliance version is from a distro. For driver acceptance you
>>> must test with a v4l2-compliance compiled from the git repo (git://linuxtv.org/v4l-utils.git).
>>>
>>> Also, since this driver uses the media controller, you must run v4l2-compliance
>>> with the -m /dev/mediaX option. This will test the compliance of all devices
>>> reported by the media controller.
>>>
>>>>
>>>> Compliance test for stf camss device /dev/video1:
>>>>
>>>> Driver Info:
>>>> Driver name : stf camss
>>>
>>> The module is called starfive-camss, so shouldn't the driver name reported here
>>> be the same?
>>>
>>>> Card type : Starfive Camera Subsystem
>>>> Bus info : platform:19840000.camss
>>>> Driver version : 6.5.0
>>>> Capabilities : 0x84200001
>>>> Video Capture
>>>> Streaming
>>>> Extended Pix Format
>>>> Device Capabilities
>>>> Device Caps : 0x04200001
>>>> Video Capture
>>>> Streaming
>>>> Extended Pix Format
>>>> Media Driver Info:
>>>> Driver name : starfive-camss
>>>
>>> It's correct in the media controller information.
>>>
>>>> Model : Starfive Camera Subsystem
>>>> Serial :
>>>> Bus info : platform:19840000.camss
>>>> Media version : 6.5.0
>>>> Hardware revision: 0x00000000 (0)
>>>> Driver version : 6.5.0
>>>> Interface Info:
>>>> ID : 0x0300000a
>>>> Type : V4L Video
>>>> Entity Info:
>>>> ID : 0x00000008 (8)
>>>> Name : capture_yuv
>>>> Function : V4L2 I/O
>>>> Pad 0x01000009 : 0: Sink
>>>> Link 0x0200000c: from remote pad 0x1000003 of entity 'stf_isp' (Unknown Function (00004009)): Data, Enabled
>>>
>>> Hmm, this reports "Unknown Function". I bet that when you run v4l2-compliance
>>> with the -m option it will fail on this. If not, then that's likely a bug in
>>> the compliance test, please let me know if that's the case.
>>>
>>
>> Hi Hans,
>>
>> The following is the latest test log, which does not report a failure, but
>> also reports "Unknown Function".
>>
>> I make the following settings in the stf-isp.c file:
>> v4l2_subdev.entity.function = MEDIA_ENT_F_PROC_VIDEO_ISP;
>>
>
> Can you post the output of:
>
> v4l2-compliance --verbose -M /dev/media0
>
> I am beginning to suspect that utils/common/media-info.cpp is out-of-date:
> it is missing MEDIA_ENT_F_PROC_VIDEO_ISP.
Yes, this was missing. I've pushed a fix for this.
Regards,
Hans
>
> But I don't understand why v4l2-compliance didn't fail on this.
>
> Regards,
>
> Hans
