The mode field of the imx219 structure is only used in imx219_init_controls(), after the probe function sets it to point to the default mode. Use the default mode directly when initializing controls, and drop the mode field from the imx219 structure. Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> --- drivers/media/i2c/imx219.c | 20 +++++++------------- 1 file changed, 7 insertions(+), 13 deletions(-) diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c index 85b7e3f4f4d0..c9c68a0f3b46 100644 --- a/drivers/media/i2c/imx219.c +++ b/drivers/media/i2c/imx219.c @@ -363,9 +363,6 @@ struct imx219 { struct v4l2_ctrl *vblank; struct v4l2_ctrl *hblank; - /* Current mode */ - const struct imx219_mode *mode; - /* Streaming on/off */ bool streaming; @@ -584,7 +581,6 @@ static int imx219_set_pad_format(struct v4l2_subdev *sd, *crop = mode->crop; if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) { - imx219->mode = mode; /* Update limits and set FPS to default */ __v4l2_ctrl_modify_range(imx219->vblank, IMX219_VBLANK_MIN, IMX219_VTS_MAX - mode->height, 1, @@ -967,8 +963,8 @@ static unsigned long imx219_get_pixel_rate(struct imx219 *imx219) static int imx219_init_controls(struct imx219 *imx219) { struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd); + const struct imx219_mode *mode = &supported_modes[0]; struct v4l2_ctrl_handler *ctrl_hdlr; - unsigned int height = imx219->mode->height; struct v4l2_fwnode_device_properties props; int exposure_max, exposure_def, hblank; int i, ret; @@ -997,15 +993,15 @@ static int imx219_init_controls(struct imx219 *imx219) /* Initial vblank/hblank/exposure parameters based on current mode */ imx219->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops, V4L2_CID_VBLANK, IMX219_VBLANK_MIN, - IMX219_VTS_MAX - height, 1, - imx219->mode->vts_def - height); - hblank = IMX219_PPL_DEFAULT - imx219->mode->width; + IMX219_VTS_MAX - mode->height, 1, + mode->vts_def - mode->height); + hblank = IMX219_PPL_DEFAULT - mode->width; imx219->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops, V4L2_CID_HBLANK, hblank, hblank, 1, hblank); if (imx219->hblank) imx219->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; - exposure_max = imx219->mode->vts_def - 4; + exposure_max = mode->vts_def - 4; exposure_def = (exposure_max < IMX219_EXPOSURE_DEFAULT) ? exposure_max : IMX219_EXPOSURE_DEFAULT; imx219->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops, @@ -1192,10 +1188,8 @@ static int imx219_probe(struct i2c_client *client) if (ret) goto error_power_off; - /* Set default mode to max resolution */ - imx219->mode = &supported_modes[0]; - - /* sensor doesn't enter LP-11 state upon power up until and unless + /* + * Sensor doesn't enter LP-11 state upon power up until and unless * streaming is started, so upon power up switch the modes to: * streaming -> standby */ -- Regards, Laurent Pinchart