On 31/07/2023 11:29, Jai Luthra wrote:
From: Pratyush Yadav <p.yadav@xxxxxx>
The stream stop procedure says that the STOP bit should be set when the
stream is to be stopped, and then the ready bit in stream status
register polled to make sure the STOP operation is finished.
Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx>
Signed-off-by: Jai Luthra <j-luthra@xxxxxx>
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
---
v7->v8:
- Fix bug where intention was to wait till stream status is idle, i.e.
STREAM_STATUS[31] -> 0 - but we were instead checking the opposite
drivers/media/platform/cadence/cdns-csi2rx.c | 18 +++++++++++++++++-
1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/drivers/media/platform/cadence/cdns-csi2rx.c b/drivers/media/platform/cadence/cdns-csi2rx.c
index 30cdc260b46a..a17ef88dff82 100644
--- a/drivers/media/platform/cadence/cdns-csi2rx.c
+++ b/drivers/media/platform/cadence/cdns-csi2rx.c
@@ -8,6 +8,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_graph.h>
@@ -41,8 +42,12 @@
#define CSI2RX_STREAM_CTRL_REG(n) (CSI2RX_STREAM_BASE(n) + 0x000)
#define CSI2RX_STREAM_CTRL_SOFT_RST BIT(4)
+#define CSI2RX_STREAM_CTRL_STOP BIT(1)
#define CSI2RX_STREAM_CTRL_START BIT(0)
+#define CSI2RX_STREAM_STATUS_REG(n) (CSI2RX_STREAM_BASE(n) + 0x004)
+#define CSI2RX_STREAM_STATUS_RDY BIT(31)
+
#define CSI2RX_STREAM_DATA_CFG_REG(n) (CSI2RX_STREAM_BASE(n) + 0x008)
#define CSI2RX_STREAM_DATA_CFG_EN_VC_SELECT BIT(31)
#define CSI2RX_STREAM_DATA_CFG_VC_SELECT(n) BIT((n) + 16)
@@ -314,13 +319,24 @@ static int csi2rx_start(struct csi2rx_priv *csi2rx)
static void csi2rx_stop(struct csi2rx_priv *csi2rx)
{
unsigned int i;
+ u32 val;
+ int ret;
clk_prepare_enable(csi2rx->p_clk);
reset_control_assert(csi2rx->sys_rst);
clk_disable_unprepare(csi2rx->sys_clk);
for (i = 0; i < csi2rx->max_streams; i++) {
- writel(0, csi2rx->base + CSI2RX_STREAM_CTRL_REG(i));
+ writel(CSI2RX_STREAM_CTRL_STOP,
+ csi2rx->base + CSI2RX_STREAM_CTRL_REG(i));
+
+ ret = readl_relaxed_poll_timeout(csi2rx->base +
+ CSI2RX_STREAM_STATUS_REG(i),
+ val,
+ !(val & CSI2RX_STREAM_STATUS_RDY),
+ 10, 10000);
+ if (ret)
+ dev_warn(csi2rx->dev, "Failed to stop stream%u\n", i);
When adding streams support, I think the driver might need some
adjustments. E.g. above says that e.g. stopping stream2 failed, which
will be quite confusing as the reader probably thinks it refers to the
"logical" streams. It would be helpful if it was always clear which of
the streams the driver refers to (in prints, but also in code).
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@xxxxxxxxxxxxxxxx>
Tomi
