I test this on my 3A5000 + 7A1000 and 3A5000 + 7A2000 desktop, and this works well, so: Tested-by: Liu Peibao <liupeibao@xxxxxxxxxxx> Br, Peibao On 5/15/23 11:57 PM, Sui Jingfeng wrote: > Loongson display controller IP has been integrated in both Loongson north > bridge chipset(ls7a1000/ls7a2000) and Loongson SoCs(ls2k1000/ls2k2000), it > has been even included in Loongson self-made BMC products. > > This display controller is a PCI device. It has two display pipes and each > display pipe support a primary plane and a cursor plane. For the DC in the > ls7a1000 and ls2k1000, each display pipe has a DVO output interface which > provide RGB888 signals, vertical & horizontal synchronisations and pixel > clock. Each CRTC is able to support 1920x1080@60Hz, the maximum resolution > of each display pipe is 2048x2048 according to the hardware spec. > > For the DC in LS7A2000, each display pipe is equipped with a built-in HDMI > encoder which is compliant with the HDMI 1.4 specification, thus it support > 3840x2160@30Hz. The first display pipe is also equipped with a transparent > vga encoder which is parallel with the HDMI encoder. The DC in LS7A2000 is > more complete compare with the one in old chips, besides above feature, it > has two hardware cursors, two hardware vblank counter and two scanout > position recorders unit. It also support tiled framebuffer format which > can be scanout the tiled framebuffer rendered by the LoongGPU directly. > > v1 -> v2: > 1) Use hpd status reg when polling for ls7a2000 > 2) Fix all warnings emerged when compile with W=1 > > v2 -> v3: > 1) Add COMPILE_TEST in Kconfig and make the driver off by default > 2) Alphabetical sorting headers (Thomas) > 3) Untangle register access functions as much as possible (Thomas) > 4) Switch to TTM based memory manager and prefer cached mapping > for Loongson SoC (Thomas) > 5) Add chip id detection method, now all models are distinguishable. > 6) Revise builtin HDMI phy driver, nearly all main stream mode > below 4K@30Hz is tested, this driver supported these mode very > well including clone display mode and extend display mode. > > v3 -> v4: > 1) Quickly fix a small mistake. > > v4 -> v5: > 1) Drop potential support for Loongson 2K series SoC temporary, > this part should be resend with the DT binding patch in the future. > 2) Add per display pipe debugfs support to the builtin HDMI encoder. > 3) Rewrite atomic_update() for hardware cursors plane(Thomas) > 4) Rewrite encoder and connector initialization part, untangle it > according to the chip(Thomas). > > v5 -> v6: > 1) Remove stray code which didn't get used, say lsdc_of_get_reserved_ram > 2) Fix all typos I could found, make sentences and code more readable > 3) Untangle lsdc_hdmi*_connector_detect() function according to the pipe > 4) After a serious consideration, we rename this driver as loongson. > Because we also have drivers toward the LoongGPU IP in LS7A2000 and > LS2K2000. Besides, there are also drivers about the external encoder, > HDMI audio driver and vbios support etc. This patch only provide DC > driver part, my teammate Li Yi believe that loongson will be more > suitable for loongson graphics than lsdc in the long run. > > loongson.ko = LSDC + LoongGPU + encoders driver + vbios/DT ... > > v6 -> v7: > 1) Add prime support, self-sharing is works. sharing buffer with etnaviv > is also tested, and its works with limitation. > 2) Implement buffer objects tracking with list_head. > 3) S3(sleep to RAM) is tested on ls3a5000+ls7a2000 evb and it works. > 4) Rewrite lsdc_bo_move, since ttm core stop allocating resources > during BO creation. Patch V1 ~ V6 of this series no longer works > on latest kernel. Thus, we send V7 to revival them. > > v7 -> v8: > 1) Zero a compile warnnings on 32-bit platform, compile with W=1 > 2) Revise lsdc_bo_gpu_offset() and minor cleanup > 3) Pageflip tested on the virtual terminal with following commands > > modetest -M loongson -s 32:1920x1080 -v > modetest -M loongson -s 34:1920x1080 -v -F tiles > > It works like a charm, when running pageflip test with dual screnn > configuration, another two additional bo created by the modetest > emerged, VRAM usage up to 40+MB, well we have at least 64MB, still > enough. > > # cat bos > > bo[0000]: size: 8112kB VRAM > bo[0001]: size: 16kB VRAM > bo[0002]: size: 16kB VRAM > bo[0003]: size: 16208kB VRAM > bo[0004]: size: 8112kB VRAM > bo[0005]: size: 8112kB VRAM > > v8 -> v9: > 1) Select I2C and I2C_ALGOBIT in Kconfig and should depend on MMU. > 2) Using pci_get_domain_bus_and_slot to get the GPU device. > 3) Other minor improvements. > > Those patches are tested on ls3a5000 + ls7a1000 CRB, ls3a5000 + ls7a2000 > evb, and lemote a1901 board(ls3a4000 + ls7a1000). On loongson mips CPU, > the write combine support should be enabled, to get a decent performance > for writing framebuffer data to the VRAM. > > v9 -> v10: > 1) Revise lsdc_drm_freeze() to implement S3 completely and correctly. > I suddenly realized that pinned buffer can not move and VRAM lost > power when sleep to RAM. Thus, the data in the buffer who is pinned > in VRAM will get lost when resume. Yet it's not big problem because > we are software rendering solution which relay on the CPU update the > front framebuffer. We can see the garbage data when resume from S3, > but the screen will show correct image as I move the cursor. This is > due to the cpu repaint. v10 of this patch make S3 perfect by unpin > all of BOs in VRAM, evict them all to system RAM. > > v10 -> v11: > 1) On double screen case, the single giant framebuffer is referenced by > two GEM object, hence, it will be pinned by prepare_fb() at lease two > times. This cause its pin count > 1. V10 of this patch only unpin VRAM > BOs once when suspend, which is not correct on double screen case. V11 > of this patch unpin BOs until its pin count reach to zero when suspend. > Then, we make the S3 support complete finally. With v11, I can't see > any garbage data after resume. Tested on both ls7a1000 and ls7a2000 > platform, with single screen and double screen configuration. > 2) Fix vblank wait timeout when disable CRTC. > 3) Test against IGT, at least fbdev test and kms_flip test passed. > 4) Rewrite pixel PLL update function, magic numbers eliminated (Emil) > 5) Drop a few common hardware features description in lsdc_desc (Emil) > 6) Drop lsdc_mode_config_mode_valid(), instead add restrictions in dumb > create function. (Emil) > 7) Untangle the ls7a1000 case and ls7a2000 case completely (Thomas) > > v11 -> v12: > none > > v12 -> v13: > 1) Add benchmark to figure out the bandwidth of the hardware platform. > Usage: > # cd /sys/kernel/debug/dri/0/ > # cat benchmark > > 2) VRAM is filled with garbage data if uninitialized, add a buffer > clearing procedure, clear it on the BO creation time. > 3) Update copyrights and adjust coding style (Huacai) > > Signed-off-by: Li Yi <liyi@xxxxxxxxxxx> > Signed-off-by: Sui Jingfeng <suijingfeng@xxxxxxxxxxx> > Cc: Maarten Lankhorst <maarten.lankhorst@xxxxxxxxxxxxxxx> > Cc: Maxime Ripard <mripard@xxxxxxxxxx> > Cc: Thomas Zimmermann <tzimmermann@xxxxxxx> > Cc: David Airlie <airlied@xxxxxxxxx> > Cc: Daniel Vetter <daniel@xxxxxxxx> > Cc: Sumit Semwal <sumit.semwal@xxxxxxxxxx> > Cc: "Christian König" <christian.koenig@xxxxxxx> > --- > drivers/gpu/drm/Kconfig | 2 + > drivers/gpu/drm/Makefile | 1 + > drivers/gpu/drm/loongson/Kconfig | 17 + > drivers/gpu/drm/loongson/Makefile | 21 + > drivers/gpu/drm/loongson/ls7a1000_outputs.c | 161 +++ > drivers/gpu/drm/loongson/ls7a2000_outputs.c | 531 +++++++++ > drivers/gpu/drm/loongson/lsdc_benchmark.c | 132 +++ > drivers/gpu/drm/loongson/lsdc_benchmark.h | 13 + > drivers/gpu/drm/loongson/lsdc_crtc.c | 1068 +++++++++++++++++++ > drivers/gpu/drm/loongson/lsdc_debugfs.c | 91 ++ > drivers/gpu/drm/loongson/lsdc_device.c | 104 ++ > drivers/gpu/drm/loongson/lsdc_drv.c | 484 +++++++++ > drivers/gpu/drm/loongson/lsdc_drv.h | 452 ++++++++ > drivers/gpu/drm/loongson/lsdc_gem.c | 324 ++++++ > drivers/gpu/drm/loongson/lsdc_gem.h | 37 + > drivers/gpu/drm/loongson/lsdc_gfxpll.c | 199 ++++ > drivers/gpu/drm/loongson/lsdc_gfxpll.h | 52 + > drivers/gpu/drm/loongson/lsdc_i2c.c | 179 ++++ > drivers/gpu/drm/loongson/lsdc_i2c.h | 29 + > drivers/gpu/drm/loongson/lsdc_irq.c | 81 ++ > drivers/gpu/drm/loongson/lsdc_irq.h | 16 + > drivers/gpu/drm/loongson/lsdc_output.h | 21 + > drivers/gpu/drm/loongson/lsdc_pixpll.c | 481 +++++++++ > drivers/gpu/drm/loongson/lsdc_pixpll.h | 86 ++ > drivers/gpu/drm/loongson/lsdc_plane.c | 639 +++++++++++ > drivers/gpu/drm/loongson/lsdc_probe.c | 56 + > drivers/gpu/drm/loongson/lsdc_probe.h | 12 + > drivers/gpu/drm/loongson/lsdc_regs.h | 400 +++++++ > drivers/gpu/drm/loongson/lsdc_ttm.c | 610 +++++++++++ > drivers/gpu/drm/loongson/lsdc_ttm.h | 99 ++ > 30 files changed, 6398 insertions(+) > create mode 100644 drivers/gpu/drm/loongson/Kconfig > create mode 100644 drivers/gpu/drm/loongson/Makefile > create mode 100644 drivers/gpu/drm/loongson/ls7a1000_outputs.c > create mode 100644 drivers/gpu/drm/loongson/ls7a2000_outputs.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_benchmark.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_benchmark.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_crtc.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_debugfs.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_device.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_drv.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_drv.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_gem.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_gem.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_gfxpll.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_gfxpll.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_i2c.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_i2c.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_irq.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_irq.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_output.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_pixpll.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_pixpll.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_plane.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_probe.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_probe.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_regs.h > create mode 100644 drivers/gpu/drm/loongson/lsdc_ttm.c > create mode 100644 drivers/gpu/drm/loongson/lsdc_ttm.h
