Re: [PATCH v1 02/11] media: dt-bindings: starfive,jh7110-mipi-csi2: add binding docmuent

[Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>]

On 02/03/2023 10:19, jack.zhu wrote:
> Add DT binding document for Starfive MIPI CSI2 receiver

Subject: drop second/last, redundant "add binding document". The
"dt-bindings" prefix is already stating that these are bindings and it
is a document. Write something useful instead.

> 
> Signed-off-by: jack.zhu <jack.zhu@xxxxxxxxxxxxxxxx>
> ---
>  .../media/starfive,jh7110-mipi-csi2.yaml      | 177 ++++++++++++++++++
>  1 file changed, 177 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/starfive,jh7110-mipi-csi2.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/starfive,jh7110-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/starfive,jh7110-mipi-csi2.yaml
> new file mode 100644
> index 000000000000..6569fac9e856
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/starfive,jh7110-mipi-csi2.yaml
> @@ -0,0 +1,177 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)

Why for patch 1 and 2 you are using difference SPDX?

> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/starfive,jh7110-mipi-csi2.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Starfive JH7110 MIPI CSI-2 receiver
> +
> +maintainers:
> +  - Jack Zhu <jack.zhu@xxxxxxxxxxxxxxxx>
> +  - Changhuang Liang <changhuang.liang@xxxxxxxxxxxxxxxx>
> +
> +description: |-

Drop |-

> +  The JH7110 MIPI CSI-2 receiver device is responsible for handling CSI2
> +  protocol based camera sensor data stream.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - starfive,jh7110-csi2rx
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: CSI2Rx system clock
> +      - description: Gated Register bank clock for APB interface
> +      - description: pixel Clock for Stream interface 0
> +      - description: pixel Clock for Stream interface 1
> +      - description: pixel Clock for Stream interface 2
> +      - description: pixel Clock for Stream interface 3
> +
> +  clock-names:
> +    items:
> +      - const: sys_clk
> +      - const: p_clk
> +      - const: pixel_if0_clk
> +      - const: pixel_if1_clk
> +      - const: pixel_if2_clk
> +      - const: pixel_if3_clk

Drop _clk suffixes

> +
> +  resets:
> +    items:
> +      - description: CSI2Rx system reset
> +      - description: Gated Register bank reset for APB interface
> +      - description: pixel reset for Stream interface 0
> +      - description: pixel reset for Stream interface 1
> +      - description: pixel reset for Stream interface 2
> +      - description: pixel reset for Stream interface 3
> +
> +  reset-names:
> +    items:
> +      - const: sys_rst

Drop _rst suffixes

> +      - const: p_rst
> +      - const: pixel_if0_rst
> +      - const: pixel_if1_rst
> +      - const: pixel_if2_rst
> +      - const: pixel_if3_rst
> +
> +  phys:
> +    maxItems: 1
> +    description: MIPI D-PHY
> +
> +  phy-names:
> +    items:
> +      - const: dphy
> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description:
> +          Input port node, single endpoint describing the CSI-2 transmitter.
> +
> +        properties:
> +          endpoint:
> +            $ref: video-interfaces.yaml#
> +            unevaluatedProperties: false
> +
> +            properties:
> +              bus-type:
> +                items:

This is not an array.

> +                  - const: 4
> +
> +              clock-lanes:
> +                maxItems: 1

Not an array...

> +
> +              data-lanes:
> +                minItems: 1
> +                maxItems: 4
> +                items:
> +                  maximum: 4
> +
> +            required:
> +              - bus-type

Since this is fixed 4, do you actually require it? Why?

> +              - clock-lanes
> +              - data-lanes
> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description:
> +          Output port node
> +
> +    required:
> +      - port@0
> +      - port@1
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +  - resets
> +  - reset-names
> +  - phys
> +  - phy-names
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +

Drop blank line

> +    csi2rx: csi-bridge@19800000 {

Maybe just "csi@"?
> +        compatible = "starfive,jh7110-csi2rx";
> +        reg = <0x19800000 0x10000>;
> +        clocks = <&ispcrg 7>,
> +            <&ispcrg 6>,

Indentation looks odd... did you align it?

> +            <&ispcrg 8>,
> +            <&ispcrg 9>,
> +            <&ispcrg 10>,
> +            <&ispcrg 11>;
> +        clock-names = "sys_clk", "p_clk",
> +            "pixel_if0_clk", "pixel_if1_clk",
> +            "pixel_if2_clk", "pixel_if3_clk";
> +        resets = <&ispcrg 9>,
> +            <&ispcrg 4>,
> +            <&ispcrg 5>,
> +            <&ispcrg 6>,
> +            <&ispcrg 7>,
> +            <&ispcrg 8>;
> +        reset-names = "sys_rst", "p_rst",
> +            "pixel_if0_rst", "pixel_if1_rst",
> +            "pixel_if2_rst", "pixel_if3_rst";
> +        phys = <&csi_phy>;
> +        phy-names = "dphy";


Best regards,
Krzysztof