Hi Dave,
thanks for the patch.
Am Dienstag, 31. Januar 2023, 20:20:16 CET schrieb Dave Stevenson:
> The sensor supports H & V flips, so add the relevant hooks for
> V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
>
> Note that the Bayer order is maintained as the readout area
> shifts by 1 pixel in the appropriate direction (note the
> comment about the top margin being 8 pixels whilst the bottom
> margin is 9). The V4L2_SEL_TGT_CROP region is therefore
> adjusted appropriately.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
> ---
> drivers/media/i2c/imx290.c | 37 ++++++++++++++++++++++++++++++++++---
> 1 file changed, 34 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> index 7f6746f74040..d2b7534f2c51 100644
> --- a/drivers/media/i2c/imx290.c
> +++ b/drivers/media/i2c/imx290.c
> @@ -227,6 +227,8 @@ struct imx290 {
> struct v4l2_ctrl *hblank;
> struct v4l2_ctrl *vblank;
> struct v4l2_ctrl *exposure;
> + struct v4l2_ctrl *hflip;
> + struct v4l2_ctrl *vflip;
> };
>
> static inline struct imx290 *to_imx290(struct v4l2_subdev *_sd)
> @@ -801,6 +803,24 @@ static int imx290_set_ctrl(struct v4l2_ctrl *ctrl)
> NULL);
> break;
>
> + case V4L2_CID_HFLIP:
> + case V4L2_CID_VFLIP:
> + {
> + u32 reg;
> +
> + /* WINMODE is in bits [6:4], so need to read-modify-write
*/
> + ret = imx290_read(imx290, IMX290_CTRL_07, ®);
> + if (ret)
> + break;
> + reg &= ~(IMX290_HREVERSE | IMX290_VREVERSE);
> + if (imx290->hflip->val)
> + reg |= IMX290_HREVERSE;
> + if (imx290->vflip->val)
> + reg |= IMX290_VREVERSE;
> + ret = imx290_write(imx290, IMX290_CTRL_07, reg, NULL);
> + break;
> + }
Given the grab while streaming is on, it can't be changed while streaming. But
then again the pm_runtime check above will prevent setting the registers while
streaming is off.
> +
> default:
> ret = -EINVAL;
> break;
> @@ -853,7 +873,7 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> if (ret < 0)
> return ret;
>
> - v4l2_ctrl_handler_init(&imx290->ctrls, 9);
> + v4l2_ctrl_handler_init(&imx290->ctrls, 11);
>
> /*
> * The sensor has an analog gain and a digital gain, both controlled
> @@ -909,6 +929,11 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> imx290->vblank = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> V4L2_CID_VBLANK, 1, 1, 1,
1);
>
> + imx290->hflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> + V4L2_CID_HFLIP, 0, 1, 1,
0);
> + imx290->vflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> + V4L2_CID_VFLIP, 0, 1, 1,
0);
> +
> v4l2_ctrl_new_fwnode_properties(&imx290->ctrls, &imx290_ctrl_ops,
> &props);
>
> @@ -1030,6 +1055,9 @@ static int imx290_set_stream(struct v4l2_subdev *sd,
> int enable) pm_runtime_put_autosuspend(imx290->dev);
> }
>
> + /* vflip and hflip cannot change during streaming */
> + __v4l2_ctrl_grab(imx290->vflip, enable);
> + __v4l2_ctrl_grab(imx290->hflip, enable);
Why is this grab necessary? While trying to remove these lines, I can flip the
image while streaming.
Best regards,
Alexander
> unlock:
> v4l2_subdev_unlock_state(state);
> return ret;
> @@ -1115,6 +1143,7 @@ static int imx290_get_selection(struct v4l2_subdev
> *sd, struct v4l2_subdev_state *sd_state,
> struct v4l2_subdev_selection *sel)
> {
> + struct imx290 *imx290 = to_imx290(sd);
> struct v4l2_mbus_framefmt *format;
>
> switch (sel->target) {
> @@ -1122,9 +1151,11 @@ static int imx290_get_selection(struct v4l2_subdev
> *sd, format = v4l2_subdev_get_pad_format(sd, sd_state, 0);
>
> sel->r.top = IMX920_PIXEL_ARRAY_MARGIN_TOP
> - + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT -
format->height) / 2;
> + + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT -
format->height) / 2
> + + imx290->vflip->val;
> sel->r.left = IMX920_PIXEL_ARRAY_MARGIN_LEFT
> - + (IMX290_PIXEL_ARRAY_RECORDING_WIDTH -
format->width) / 2;
> + + (IMX290_PIXEL_ARRAY_RECORDING_WIDTH -
format->width) / 2
> + + imx290->hflip->val;
> sel->r.width = format->width;
> sel->r.height = format->height;
