The ttpci driver does not use the vb2 framework for streaming video, instead it uses the old vb1 framework and nobody stepped in to convert this driver to vb2. The hardware is very old, so the decision was made to remove it altogether since we want to get rid of the old vb1 framework. Signed-off-by: Hans Verkuil <hverkuil-cisco@xxxxxxxxx> --- .../admin-guide/media/pci-cardlist.rst | 1 - .../staging/media/deprecated/saa7146/Kconfig | 1 - .../staging/media/deprecated/saa7146/Makefile | 2 +- .../media/deprecated/saa7146/ttpci/Kconfig | 95 - .../media/deprecated/saa7146/ttpci/Makefile | 13 - .../media/deprecated/saa7146/ttpci/TODO | 7 - .../deprecated/saa7146/ttpci/budget-av.c | 1622 ----------------- .../deprecated/saa7146/ttpci/budget-ci.c | 1574 ---------------- .../deprecated/saa7146/ttpci/budget-core.c | 603 ------ .../media/deprecated/saa7146/ttpci/budget.c | 883 --------- .../media/deprecated/saa7146/ttpci/budget.h | 129 -- 11 files changed, 1 insertion(+), 4929 deletions(-) delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/Kconfig delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/Makefile delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/TODO delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/budget-av.c delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/budget-ci.c delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/budget-core.c delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/budget.c delete mode 100644 drivers/staging/media/deprecated/saa7146/ttpci/budget.h diff --git a/Documentation/admin-guide/media/pci-cardlist.rst b/Documentation/admin-guide/media/pci-cardlist.rst index 42528795d4da..aca13c7e8508 100644 --- a/Documentation/admin-guide/media/pci-cardlist.rst +++ b/Documentation/admin-guide/media/pci-cardlist.rst @@ -67,7 +67,6 @@ cx88xx Conexant 2388x (bt878 successor) ddbridge Digital Devices bridge dm1105 SDMC DM1105 based PCI cards dt3155 DT3155 frame grabber -dvb-ttpci AV7110 cards earth-pt1 PT1 cards earth-pt3 Earthsoft PT3 cards hexium_gemini Hexium Gemini frame grabber diff --git a/drivers/staging/media/deprecated/saa7146/Kconfig b/drivers/staging/media/deprecated/saa7146/Kconfig index d0cb52164ff8..3d2e2120788e 100644 --- a/drivers/staging/media/deprecated/saa7146/Kconfig +++ b/drivers/staging/media/deprecated/saa7146/Kconfig @@ -1,4 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 source "drivers/staging/media/deprecated/saa7146/common/Kconfig" source "drivers/staging/media/deprecated/saa7146/saa7146/Kconfig" -source "drivers/staging/media/deprecated/saa7146/ttpci/Kconfig" diff --git a/drivers/staging/media/deprecated/saa7146/Makefile b/drivers/staging/media/deprecated/saa7146/Makefile index 9d99fdedf813..71866795174e 100644 --- a/drivers/staging/media/deprecated/saa7146/Makefile +++ b/drivers/staging/media/deprecated/saa7146/Makefile @@ -1,2 +1,2 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-y += common/ saa7146/ ttpci/ +obj-y += common/ saa7146/ diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/Kconfig b/drivers/staging/media/deprecated/saa7146/ttpci/Kconfig deleted file mode 100644 index 8c85ed58e938..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/Kconfig +++ /dev/null @@ -1,95 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -config DVB_BUDGET_CORE - tristate "SAA7146 DVB cards (aka Budget, Nova-PCI) (DEPRECATED)" - depends on DVB_CORE && PCI && I2C - select VIDEO_SAA7146 - select TTPCI_EEPROM - help - Support for simple SAA7146 based DVB cards - (so called Budget- or Nova-PCI cards) without onboard - MPEG2 decoder. - -config DVB_BUDGET - tristate "Budget cards (DEPRECATED)" - depends on DVB_BUDGET_CORE && I2C - select DVB_STV0299 if MEDIA_SUBDRV_AUTOSELECT - select DVB_VES1X93 if MEDIA_SUBDRV_AUTOSELECT - select DVB_VES1820 if MEDIA_SUBDRV_AUTOSELECT - select DVB_L64781 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA8083 if MEDIA_SUBDRV_AUTOSELECT - select DVB_S5H1420 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA10086 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA826X if MEDIA_SUBDRV_AUTOSELECT - select DVB_LNBP21 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA1004X if MEDIA_SUBDRV_AUTOSELECT - select DVB_ISL6423 if MEDIA_SUBDRV_AUTOSELECT - select DVB_STV090x if MEDIA_SUBDRV_AUTOSELECT - select DVB_STV6110x if MEDIA_SUBDRV_AUTOSELECT - help - Support for simple SAA7146 based DVB cards (so called Budget- - or Nova-PCI cards) without onboard MPEG2 decoder, and without - analog inputs or an onboard Common Interface connector. - - This driver is deprecated and is scheduled for removal by - the beginning of 2023. See the TODO file for more information. - - Say Y if you own such a card and want to use it. - - To compile this driver as a module, choose M here: the - module will be called budget. - -config DVB_BUDGET_CI - tristate "Budget cards with onboard CI connector (DEPRECATED)" - depends on DVB_BUDGET_CORE && I2C - select DVB_STV0297 if MEDIA_SUBDRV_AUTOSELECT - select DVB_STV0299 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA1004X if MEDIA_SUBDRV_AUTOSELECT - select DVB_STB0899 if MEDIA_SUBDRV_AUTOSELECT - select DVB_STB6100 if MEDIA_SUBDRV_AUTOSELECT - select DVB_LNBP21 if MEDIA_SUBDRV_AUTOSELECT - select DVB_STV0288 if MEDIA_SUBDRV_AUTOSELECT - select DVB_STB6000 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA10023 if MEDIA_SUBDRV_AUTOSELECT - select MEDIA_TUNER_TDA827X if MEDIA_SUBDRV_AUTOSELECT - depends on RC_CORE - help - Support for simple SAA7146 based DVB cards - (so called Budget- or Nova-PCI cards) without onboard - MPEG2 decoder, but with onboard Common Interface connector. - - Note: The Common Interface is not yet supported by this driver - due to lack of information from the vendor. - - This driver is deprecated and is scheduled for removal by - the beginning of 2023. See the TODO file for more information. - - Say Y if you own such a card and want to use it. - - To compile this driver as a module, choose M here: the - module will be called budget-ci. - -config DVB_BUDGET_AV - tristate "Budget cards with analog video inputs (DEPRECATED)" - depends on DVB_BUDGET_CORE && I2C - select VIDEO_SAA7146_VV - depends on VIDEO_DEV # dependencies of VIDEO_SAA7146_VV - select DVB_PLL if MEDIA_SUBDRV_AUTOSELECT - select DVB_STV0299 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA1004X if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA10021 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA10023 if MEDIA_SUBDRV_AUTOSELECT - select DVB_STB0899 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TDA8261 if MEDIA_SUBDRV_AUTOSELECT - select DVB_TUA6100 if MEDIA_SUBDRV_AUTOSELECT - help - Support for simple SAA7146 based DVB cards - (so called Budget- or Nova-PCI cards) without onboard - MPEG2 decoder, but with one or more analog video inputs. - - This driver is deprecated and is scheduled for removal by - the beginning of 2023. See the TODO file for more information. - - Say Y if you own such a card and want to use it. - - To compile this driver as a module, choose M here: the - module will be called budget-av. diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/Makefile b/drivers/staging/media/deprecated/saa7146/ttpci/Makefile deleted file mode 100644 index b0708f6e40cc..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/Makefile +++ /dev/null @@ -1,13 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -# -# Makefile for the kernel SAA7146 FULL TS DVB device driver -# - -obj-$(CONFIG_DVB_BUDGET_CORE) += budget-core.o -obj-$(CONFIG_DVB_BUDGET) += budget.o -obj-$(CONFIG_DVB_BUDGET_AV) += budget-av.o -obj-$(CONFIG_DVB_BUDGET_CI) += budget-ci.o - -ccflags-y += -I $(srctree)/drivers/media/dvb-frontends/ -ccflags-y += -I $(srctree)/drivers/media/tuners -ccflags-y += -I $(srctree)/drivers/media/common diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/TODO b/drivers/staging/media/deprecated/saa7146/ttpci/TODO deleted file mode 100644 index c9ae2ec79cea..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/TODO +++ /dev/null @@ -1,7 +0,0 @@ -The saa7146-based drivers are one of the few drivers still not using -the vb2 framework, so these drivers are now deprecated with the intent of -removing them altogether by the beginning of 2023. - -In order to keep these drivers they have to be converted to vb2. -If someone is interested in doing this work, then contact the -linux-media mailinglist (https://linuxtv.org/lists.php). diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/budget-av.c b/drivers/staging/media/deprecated/saa7146/ttpci/budget-av.c deleted file mode 100644 index 0c61a2dec221..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/budget-av.c +++ /dev/null @@ -1,1622 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * budget-av.c: driver for the SAA7146 based Budget DVB cards - * with analog video in - * - * Compiled from various sources by Michael Hunold <michael@xxxxxxx> - * - * CI interface support (c) 2004 Olivier Gournet <ogournet@xxxxxxxxxx> & - * Andrew de Quincey <adq_dvb@xxxxxxxxxxxxx> - * - * Copyright (C) 2002 Ralph Metzler <rjkm@xxxxxxxxxxxxxx> - * - * Copyright (C) 1999-2002 Ralph Metzler - * & Marcus Metzler for convergence integrated media GmbH - * - * the project's page is at https://linuxtv.org - */ - -#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt - -#include "budget.h" -#include "stv0299.h" -#include "stb0899_drv.h" -#include "stb0899_reg.h" -#include "stb0899_cfg.h" -#include "tda8261.h" -#include "tda8261_cfg.h" -#include "tda1002x.h" -#include "tda1004x.h" -#include "tua6100.h" -#include "dvb-pll.h" -#include "../common/saa7146_vv.h" -#include <linux/module.h> -#include <linux/errno.h> -#include <linux/slab.h> -#include <linux/interrupt.h> -#include <linux/input.h> -#include <linux/spinlock.h> - -#include <media/dvb_ca_en50221.h> - -#define DEBICICAM 0x02420000 - -#define SLOTSTATUS_NONE 1 -#define SLOTSTATUS_PRESENT 2 -#define SLOTSTATUS_RESET 4 -#define SLOTSTATUS_READY 8 -#define SLOTSTATUS_OCCUPIED (SLOTSTATUS_PRESENT|SLOTSTATUS_RESET|SLOTSTATUS_READY) - -DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); - -struct budget_av { - struct budget budget; - struct video_device vd; - int cur_input; - int has_saa7113; - struct tasklet_struct ciintf_irq_tasklet; - int slot_status; - struct dvb_ca_en50221 ca; - u8 reinitialise_demod:1; -}; - -static int ciintf_slot_shutdown(struct dvb_ca_en50221 *ca, int slot); - - -/* GPIO Connections: - * 0 - Vcc/Reset (Reset is controlled by capacitor). Resets the frontend *AS WELL*! - * 1 - CI memory select 0=>IO memory, 1=>Attribute Memory - * 2 - CI Card Enable (Active Low) - * 3 - CI Card Detect - */ - -/**************************************************************************** - * INITIALIZATION - ****************************************************************************/ - -static u8 i2c_readreg(struct i2c_adapter *i2c, u8 id, u8 reg) -{ - u8 mm1[] = { 0x00 }; - u8 mm2[] = { 0x00 }; - struct i2c_msg msgs[2]; - - msgs[0].flags = 0; - msgs[1].flags = I2C_M_RD; - msgs[0].addr = msgs[1].addr = id / 2; - mm1[0] = reg; - msgs[0].len = 1; - msgs[1].len = 1; - msgs[0].buf = mm1; - msgs[1].buf = mm2; - - i2c_transfer(i2c, msgs, 2); - - return mm2[0]; -} - -static int i2c_readregs(struct i2c_adapter *i2c, u8 id, u8 reg, u8 * buf, u8 len) -{ - u8 mm1[] = { reg }; - struct i2c_msg msgs[2] = { - {.addr = id / 2,.flags = 0,.buf = mm1,.len = 1}, - {.addr = id / 2,.flags = I2C_M_RD,.buf = buf,.len = len} - }; - - if (i2c_transfer(i2c, msgs, 2) != 2) - return -EIO; - - return 0; -} - -static int i2c_writereg(struct i2c_adapter *i2c, u8 id, u8 reg, u8 val) -{ - u8 msg[2] = { reg, val }; - struct i2c_msg msgs; - - msgs.flags = 0; - msgs.addr = id / 2; - msgs.len = 2; - msgs.buf = msg; - return i2c_transfer(i2c, &msgs, 1); -} - -static int ciintf_read_attribute_mem(struct dvb_ca_en50221 *ca, int slot, int address) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - int result; - - if (slot != 0) - return -EINVAL; - - saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTHI); - udelay(1); - - result = ttpci_budget_debiread(&budget_av->budget, DEBICICAM, address & 0xfff, 1, 0, 1); - if (result == -ETIMEDOUT) { - ciintf_slot_shutdown(ca, slot); - pr_info("cam ejected 1\n"); - } - return result; -} - -static int ciintf_write_attribute_mem(struct dvb_ca_en50221 *ca, int slot, int address, u8 value) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - int result; - - if (slot != 0) - return -EINVAL; - - saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTHI); - udelay(1); - - result = ttpci_budget_debiwrite(&budget_av->budget, DEBICICAM, address & 0xfff, 1, value, 0, 1); - if (result == -ETIMEDOUT) { - ciintf_slot_shutdown(ca, slot); - pr_info("cam ejected 2\n"); - } - return result; -} - -static int ciintf_read_cam_control(struct dvb_ca_en50221 *ca, int slot, u8 address) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - int result; - - if (slot != 0) - return -EINVAL; - - saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTLO); - udelay(1); - - result = ttpci_budget_debiread(&budget_av->budget, DEBICICAM, address & 3, 1, 0, 0); - if (result == -ETIMEDOUT) { - ciintf_slot_shutdown(ca, slot); - pr_info("cam ejected 3\n"); - return -ETIMEDOUT; - } - return result; -} - -static int ciintf_write_cam_control(struct dvb_ca_en50221 *ca, int slot, u8 address, u8 value) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - int result; - - if (slot != 0) - return -EINVAL; - - saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTLO); - udelay(1); - - result = ttpci_budget_debiwrite(&budget_av->budget, DEBICICAM, address & 3, 1, value, 0, 0); - if (result == -ETIMEDOUT) { - ciintf_slot_shutdown(ca, slot); - pr_info("cam ejected 5\n"); - } - return result; -} - -static int ciintf_slot_reset(struct dvb_ca_en50221 *ca, int slot) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - struct saa7146_dev *saa = budget_av->budget.dev; - - if (slot != 0) - return -EINVAL; - - dprintk(1, "ciintf_slot_reset\n"); - budget_av->slot_status = SLOTSTATUS_RESET; - - saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTHI); /* disable card */ - - saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI); /* Vcc off */ - msleep(2); - saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO); /* Vcc on */ - msleep(20); /* 20 ms Vcc settling time */ - - saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTLO); /* enable card */ - ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB); - msleep(20); - - /* reinitialise the frontend if necessary */ - if (budget_av->reinitialise_demod) - dvb_frontend_reinitialise(budget_av->budget.dvb_frontend); - - return 0; -} - -static int ciintf_slot_shutdown(struct dvb_ca_en50221 *ca, int slot) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - struct saa7146_dev *saa = budget_av->budget.dev; - - if (slot != 0) - return -EINVAL; - - dprintk(1, "ciintf_slot_shutdown\n"); - - ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB); - budget_av->slot_status = SLOTSTATUS_NONE; - - return 0; -} - -static int ciintf_slot_ts_enable(struct dvb_ca_en50221 *ca, int slot) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - struct saa7146_dev *saa = budget_av->budget.dev; - - if (slot != 0) - return -EINVAL; - - dprintk(1, "ciintf_slot_ts_enable: %d\n", budget_av->slot_status); - - ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTA); - - return 0; -} - -static int ciintf_poll_slot_status(struct dvb_ca_en50221 *ca, int slot, int open) -{ - struct budget_av *budget_av = (struct budget_av *) ca->data; - struct saa7146_dev *saa = budget_av->budget.dev; - int result; - - if (slot != 0) - return -EINVAL; - - /* test the card detect line - needs to be done carefully - * since it never goes high for some CAMs on this interface (e.g. topuptv) */ - if (budget_av->slot_status == SLOTSTATUS_NONE) { - saa7146_setgpio(saa, 3, SAA7146_GPIO_INPUT); - udelay(1); - if (saa7146_read(saa, PSR) & MASK_06) { - if (budget_av->slot_status == SLOTSTATUS_NONE) { - budget_av->slot_status = SLOTSTATUS_PRESENT; - pr_info("cam inserted A\n"); - } - } - saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTLO); - } - - /* We also try and read from IO memory to work round the above detection bug. If - * there is no CAM, we will get a timeout. Only done if there is no cam - * present, since this test actually breaks some cams :( - * - * if the CI interface is not open, we also do the above test since we - * don't care if the cam has problems - we'll be resetting it on open() anyway */ - if ((budget_av->slot_status == SLOTSTATUS_NONE) || (!open)) { - saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTLO); - result = ttpci_budget_debiread(&budget_av->budget, DEBICICAM, 0, 1, 0, 1); - if ((result >= 0) && (budget_av->slot_status == SLOTSTATUS_NONE)) { - budget_av->slot_status = SLOTSTATUS_PRESENT; - pr_info("cam inserted B\n"); - } else if (result < 0) { - if (budget_av->slot_status != SLOTSTATUS_NONE) { - ciintf_slot_shutdown(ca, slot); - pr_info("cam ejected 5\n"); - return 0; - } - } - } - - /* read from attribute memory in reset/ready state to know when the CAM is ready */ - if (budget_av->slot_status == SLOTSTATUS_RESET) { - result = ciintf_read_attribute_mem(ca, slot, 0); - if (result == 0x1d) { - budget_av->slot_status = SLOTSTATUS_READY; - } - } - - /* work out correct return code */ - if (budget_av->slot_status != SLOTSTATUS_NONE) { - if (budget_av->slot_status & SLOTSTATUS_READY) { - return DVB_CA_EN50221_POLL_CAM_PRESENT | DVB_CA_EN50221_POLL_CAM_READY; - } - return DVB_CA_EN50221_POLL_CAM_PRESENT; - } - return 0; -} - -static int ciintf_init(struct budget_av *budget_av) -{ - struct saa7146_dev *saa = budget_av->budget.dev; - int result; - - memset(&budget_av->ca, 0, sizeof(struct dvb_ca_en50221)); - - saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO); - saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTLO); - saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTLO); - saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTLO); - - /* Enable DEBI pins */ - saa7146_write(saa, MC1, MASK_27 | MASK_11); - - /* register CI interface */ - budget_av->ca.owner = THIS_MODULE; - budget_av->ca.read_attribute_mem = ciintf_read_attribute_mem; - budget_av->ca.write_attribute_mem = ciintf_write_attribute_mem; - budget_av->ca.read_cam_control = ciintf_read_cam_control; - budget_av->ca.write_cam_control = ciintf_write_cam_control; - budget_av->ca.slot_reset = ciintf_slot_reset; - budget_av->ca.slot_shutdown = ciintf_slot_shutdown; - budget_av->ca.slot_ts_enable = ciintf_slot_ts_enable; - budget_av->ca.poll_slot_status = ciintf_poll_slot_status; - budget_av->ca.data = budget_av; - budget_av->budget.ci_present = 1; - budget_av->slot_status = SLOTSTATUS_NONE; - - if ((result = dvb_ca_en50221_init(&budget_av->budget.dvb_adapter, - &budget_av->ca, 0, 1)) != 0) { - pr_err("ci initialisation failed\n"); - goto error; - } - - pr_info("ci interface initialised\n"); - return 0; - -error: - saa7146_write(saa, MC1, MASK_27); - return result; -} - -static void ciintf_deinit(struct budget_av *budget_av) -{ - struct saa7146_dev *saa = budget_av->budget.dev; - - saa7146_setgpio(saa, 0, SAA7146_GPIO_INPUT); - saa7146_setgpio(saa, 1, SAA7146_GPIO_INPUT); - saa7146_setgpio(saa, 2, SAA7146_GPIO_INPUT); - saa7146_setgpio(saa, 3, SAA7146_GPIO_INPUT); - - /* release the CA device */ - dvb_ca_en50221_release(&budget_av->ca); - - /* disable DEBI pins */ - saa7146_write(saa, MC1, MASK_27); -} - - -static const u8 saa7113_tab[] = { - 0x01, 0x08, - 0x02, 0xc0, - 0x03, 0x33, - 0x04, 0x00, - 0x05, 0x00, - 0x06, 0xeb, - 0x07, 0xe0, - 0x08, 0x28, - 0x09, 0x00, - 0x0a, 0x80, - 0x0b, 0x47, - 0x0c, 0x40, - 0x0d, 0x00, - 0x0e, 0x01, - 0x0f, 0x44, - - 0x10, 0x08, - 0x11, 0x0c, - 0x12, 0x7b, - 0x13, 0x00, - 0x15, 0x00, 0x16, 0x00, 0x17, 0x00, - - 0x57, 0xff, - 0x40, 0x82, 0x58, 0x00, 0x59, 0x54, 0x5a, 0x07, - 0x5b, 0x83, 0x5e, 0x00, - 0xff -}; - -static int saa7113_init(struct budget_av *budget_av) -{ - struct budget *budget = &budget_av->budget; - struct saa7146_dev *saa = budget->dev; - const u8 *data = saa7113_tab; - - saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI); - msleep(200); - - if (i2c_writereg(&budget->i2c_adap, 0x4a, 0x01, 0x08) != 1) { - dprintk(1, "saa7113 not found on KNC card\n"); - return -ENODEV; - } - - dprintk(1, "saa7113 detected and initializing\n"); - - while (*data != 0xff) { - i2c_writereg(&budget->i2c_adap, 0x4a, *data, *(data + 1)); - data += 2; - } - - dprintk(1, "saa7113 status=%02x\n", i2c_readreg(&budget->i2c_adap, 0x4a, 0x1f)); - - return 0; -} - -static int saa7113_setinput(struct budget_av *budget_av, int input) -{ - struct budget *budget = &budget_av->budget; - - if (1 != budget_av->has_saa7113) - return -ENODEV; - - if (input == 1) { - i2c_writereg(&budget->i2c_adap, 0x4a, 0x02, 0xc7); - i2c_writereg(&budget->i2c_adap, 0x4a, 0x09, 0x80); - } else if (input == 0) { - i2c_writereg(&budget->i2c_adap, 0x4a, 0x02, 0xc0); - i2c_writereg(&budget->i2c_adap, 0x4a, 0x09, 0x00); - } else - return -EINVAL; - - budget_av->cur_input = input; - return 0; -} - - -static int philips_su1278_ty_ci_set_symbol_rate(struct dvb_frontend *fe, u32 srate, u32 ratio) -{ - u8 aclk = 0; - u8 bclk = 0; - u8 m1; - - aclk = 0xb5; - if (srate < 2000000) - bclk = 0x86; - else if (srate < 5000000) - bclk = 0x89; - else if (srate < 15000000) - bclk = 0x8f; - else if (srate < 45000000) - bclk = 0x95; - - m1 = 0x14; - if (srate < 4000000) - m1 = 0x10; - - stv0299_writereg(fe, 0x13, aclk); - stv0299_writereg(fe, 0x14, bclk); - stv0299_writereg(fe, 0x1f, (ratio >> 16) & 0xff); - stv0299_writereg(fe, 0x20, (ratio >> 8) & 0xff); - stv0299_writereg(fe, 0x21, (ratio) & 0xf0); - stv0299_writereg(fe, 0x0f, 0x80 | m1); - - return 0; -} - -static int philips_su1278_ty_ci_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - u32 div; - u8 buf[4]; - struct budget *budget = (struct budget *) fe->dvb->priv; - struct i2c_msg msg = {.addr = 0x61,.flags = 0,.buf = buf,.len = sizeof(buf) }; - - if ((c->frequency < 950000) || (c->frequency > 2150000)) - return -EINVAL; - - div = (c->frequency + (125 - 1)) / 125; /* round correctly */ - buf[0] = (div >> 8) & 0x7f; - buf[1] = div & 0xff; - buf[2] = 0x80 | ((div & 0x18000) >> 10) | 4; - buf[3] = 0x20; - - if (c->symbol_rate < 4000000) - buf[3] |= 1; - - if (c->frequency < 1250000) - buf[3] |= 0; - else if (c->frequency < 1550000) - buf[3] |= 0x40; - else if (c->frequency < 2050000) - buf[3] |= 0x80; - else if (c->frequency < 2150000) - buf[3] |= 0xC0; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget->i2c_adap, &msg, 1) != 1) - return -EIO; - return 0; -} - -static u8 typhoon_cinergy1200s_inittab[] = { - 0x01, 0x15, - 0x02, 0x30, - 0x03, 0x00, - 0x04, 0x7d, /* F22FR = 0x7d, F22 = f_VCO / 128 / 0x7d = 22 kHz */ - 0x05, 0x35, /* I2CT = 0, SCLT = 1, SDAT = 1 */ - 0x06, 0x40, /* DAC not used, set to high impendance mode */ - 0x07, 0x00, /* DAC LSB */ - 0x08, 0x40, /* DiSEqC off */ - 0x09, 0x00, /* FIFO */ - 0x0c, 0x51, /* OP1 ctl = Normal, OP1 val = 1 (LNB Power ON) */ - 0x0d, 0x82, /* DC offset compensation = ON, beta_agc1 = 2 */ - 0x0e, 0x23, /* alpha_tmg = 2, beta_tmg = 3 */ - 0x10, 0x3f, // AGC2 0x3d - 0x11, 0x84, - 0x12, 0xb9, - 0x15, 0xc9, // lock detector threshold - 0x16, 0x00, - 0x17, 0x00, - 0x18, 0x00, - 0x19, 0x00, - 0x1a, 0x00, - 0x1f, 0x50, - 0x20, 0x00, - 0x21, 0x00, - 0x22, 0x00, - 0x23, 0x00, - 0x28, 0x00, // out imp: normal out type: parallel FEC mode:0 - 0x29, 0x1e, // 1/2 threshold - 0x2a, 0x14, // 2/3 threshold - 0x2b, 0x0f, // 3/4 threshold - 0x2c, 0x09, // 5/6 threshold - 0x2d, 0x05, // 7/8 threshold - 0x2e, 0x01, - 0x31, 0x1f, // test all FECs - 0x32, 0x19, // viterbi and synchro search - 0x33, 0xfc, // rs control - 0x34, 0x93, // error control - 0x0f, 0x92, - 0xff, 0xff -}; - -static const struct stv0299_config typhoon_config = { - .demod_address = 0x68, - .inittab = typhoon_cinergy1200s_inittab, - .mclk = 88000000UL, - .invert = 0, - .skip_reinit = 0, - .lock_output = STV0299_LOCKOUTPUT_1, - .volt13_op0_op1 = STV0299_VOLT13_OP0, - .min_delay_ms = 100, - .set_symbol_rate = philips_su1278_ty_ci_set_symbol_rate, -}; - - -static const struct stv0299_config cinergy_1200s_config = { - .demod_address = 0x68, - .inittab = typhoon_cinergy1200s_inittab, - .mclk = 88000000UL, - .invert = 0, - .skip_reinit = 0, - .lock_output = STV0299_LOCKOUTPUT_0, - .volt13_op0_op1 = STV0299_VOLT13_OP0, - .min_delay_ms = 100, - .set_symbol_rate = philips_su1278_ty_ci_set_symbol_rate, -}; - -static const struct stv0299_config cinergy_1200s_1894_0010_config = { - .demod_address = 0x68, - .inittab = typhoon_cinergy1200s_inittab, - .mclk = 88000000UL, - .invert = 1, - .skip_reinit = 0, - .lock_output = STV0299_LOCKOUTPUT_1, - .volt13_op0_op1 = STV0299_VOLT13_OP0, - .min_delay_ms = 100, - .set_symbol_rate = philips_su1278_ty_ci_set_symbol_rate, -}; - -static int philips_cu1216_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget *budget = (struct budget *) fe->dvb->priv; - u8 buf[6]; - struct i2c_msg msg = {.addr = 0x60,.flags = 0,.buf = buf,.len = sizeof(buf) }; - int i; - -#define CU1216_IF 36125000 -#define TUNER_MUL 62500 - - u32 div = (c->frequency + CU1216_IF + TUNER_MUL / 2) / TUNER_MUL; - - buf[0] = (div >> 8) & 0x7f; - buf[1] = div & 0xff; - buf[2] = 0xce; - buf[3] = (c->frequency < 150000000 ? 0x01 : - c->frequency < 445000000 ? 0x02 : 0x04); - buf[4] = 0xde; - buf[5] = 0x20; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget->i2c_adap, &msg, 1) != 1) - return -EIO; - - /* wait for the pll lock */ - msg.flags = I2C_M_RD; - msg.len = 1; - for (i = 0; i < 20; i++) { - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget->i2c_adap, &msg, 1) == 1 && (buf[0] & 0x40)) - break; - msleep(10); - } - - /* switch the charge pump to the lower current */ - msg.flags = 0; - msg.len = 2; - msg.buf = &buf[2]; - buf[2] &= ~0x40; - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget->i2c_adap, &msg, 1) != 1) - return -EIO; - - return 0; -} - -static struct tda1002x_config philips_cu1216_config = { - .demod_address = 0x0c, - .invert = 1, -}; - -static struct tda1002x_config philips_cu1216_config_altaddress = { - .demod_address = 0x0d, - .invert = 0, -}; - -static struct tda10023_config philips_cu1216_tda10023_config = { - .demod_address = 0x0c, - .invert = 1, -}; - -static int philips_tu1216_tuner_init(struct dvb_frontend *fe) -{ - struct budget *budget = (struct budget *) fe->dvb->priv; - static u8 tu1216_init[] = { 0x0b, 0xf5, 0x85, 0xab }; - struct i2c_msg tuner_msg = {.addr = 0x60,.flags = 0,.buf = tu1216_init,.len = sizeof(tu1216_init) }; - - // setup PLL configuration - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget->i2c_adap, &tuner_msg, 1) != 1) - return -EIO; - msleep(1); - - return 0; -} - -static int philips_tu1216_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget *budget = (struct budget *) fe->dvb->priv; - u8 tuner_buf[4]; - struct i2c_msg tuner_msg = {.addr = 0x60,.flags = 0,.buf = tuner_buf,.len = - sizeof(tuner_buf) }; - int tuner_frequency = 0; - u8 band, cp, filter; - - // determine charge pump - tuner_frequency = c->frequency + 36166000; - if (tuner_frequency < 87000000) - return -EINVAL; - else if (tuner_frequency < 130000000) - cp = 3; - else if (tuner_frequency < 160000000) - cp = 5; - else if (tuner_frequency < 200000000) - cp = 6; - else if (tuner_frequency < 290000000) - cp = 3; - else if (tuner_frequency < 420000000) - cp = 5; - else if (tuner_frequency < 480000000) - cp = 6; - else if (tuner_frequency < 620000000) - cp = 3; - else if (tuner_frequency < 830000000) - cp = 5; - else if (tuner_frequency < 895000000) - cp = 7; - else - return -EINVAL; - - // determine band - if (c->frequency < 49000000) - return -EINVAL; - else if (c->frequency < 161000000) - band = 1; - else if (c->frequency < 444000000) - band = 2; - else if (c->frequency < 861000000) - band = 4; - else - return -EINVAL; - - // setup PLL filter - switch (c->bandwidth_hz) { - case 6000000: - filter = 0; - break; - - case 7000000: - filter = 0; - break; - - case 8000000: - filter = 1; - break; - - default: - return -EINVAL; - } - - // calculate divisor - // ((36166000+((1000000/6)/2)) + Finput)/(1000000/6) - tuner_frequency = (((c->frequency / 1000) * 6) + 217496) / 1000; - - // setup tuner buffer - tuner_buf[0] = (tuner_frequency >> 8) & 0x7f; - tuner_buf[1] = tuner_frequency & 0xff; - tuner_buf[2] = 0xca; - tuner_buf[3] = (cp << 5) | (filter << 3) | band; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget->i2c_adap, &tuner_msg, 1) != 1) - return -EIO; - - msleep(1); - return 0; -} - -static int philips_tu1216_request_firmware(struct dvb_frontend *fe, - const struct firmware **fw, char *name) -{ - struct budget *budget = (struct budget *) fe->dvb->priv; - - return request_firmware(fw, name, &budget->dev->pci->dev); -} - -static struct tda1004x_config philips_tu1216_config = { - - .demod_address = 0x8, - .invert = 1, - .invert_oclk = 1, - .xtal_freq = TDA10046_XTAL_4M, - .agc_config = TDA10046_AGC_DEFAULT, - .if_freq = TDA10046_FREQ_3617, - .request_firmware = philips_tu1216_request_firmware, -}; - -static u8 philips_sd1878_inittab[] = { - 0x01, 0x15, - 0x02, 0x30, - 0x03, 0x00, - 0x04, 0x7d, - 0x05, 0x35, - 0x06, 0x40, - 0x07, 0x00, - 0x08, 0x43, - 0x09, 0x02, - 0x0C, 0x51, - 0x0D, 0x82, - 0x0E, 0x23, - 0x10, 0x3f, - 0x11, 0x84, - 0x12, 0xb9, - 0x15, 0xc9, - 0x16, 0x19, - 0x17, 0x8c, - 0x18, 0x59, - 0x19, 0xf8, - 0x1a, 0xfe, - 0x1c, 0x7f, - 0x1d, 0x00, - 0x1e, 0x00, - 0x1f, 0x50, - 0x20, 0x00, - 0x21, 0x00, - 0x22, 0x00, - 0x23, 0x00, - 0x28, 0x00, - 0x29, 0x28, - 0x2a, 0x14, - 0x2b, 0x0f, - 0x2c, 0x09, - 0x2d, 0x09, - 0x31, 0x1f, - 0x32, 0x19, - 0x33, 0xfc, - 0x34, 0x93, - 0xff, 0xff -}; - -static int philips_sd1878_ci_set_symbol_rate(struct dvb_frontend *fe, - u32 srate, u32 ratio) -{ - u8 aclk = 0; - u8 bclk = 0; - u8 m1; - - aclk = 0xb5; - if (srate < 2000000) - bclk = 0x86; - else if (srate < 5000000) - bclk = 0x89; - else if (srate < 15000000) - bclk = 0x8f; - else if (srate < 45000000) - bclk = 0x95; - - m1 = 0x14; - if (srate < 4000000) - m1 = 0x10; - - stv0299_writereg(fe, 0x0e, 0x23); - stv0299_writereg(fe, 0x0f, 0x94); - stv0299_writereg(fe, 0x10, 0x39); - stv0299_writereg(fe, 0x13, aclk); - stv0299_writereg(fe, 0x14, bclk); - stv0299_writereg(fe, 0x15, 0xc9); - stv0299_writereg(fe, 0x1f, (ratio >> 16) & 0xff); - stv0299_writereg(fe, 0x20, (ratio >> 8) & 0xff); - stv0299_writereg(fe, 0x21, (ratio) & 0xf0); - stv0299_writereg(fe, 0x0f, 0x80 | m1); - - return 0; -} - -static const struct stv0299_config philips_sd1878_config = { - .demod_address = 0x68, - .inittab = philips_sd1878_inittab, - .mclk = 88000000UL, - .invert = 0, - .skip_reinit = 0, - .lock_output = STV0299_LOCKOUTPUT_1, - .volt13_op0_op1 = STV0299_VOLT13_OP0, - .min_delay_ms = 100, - .set_symbol_rate = philips_sd1878_ci_set_symbol_rate, -}; - -/* KNC1 DVB-S (STB0899) Inittab */ -static const struct stb0899_s1_reg knc1_stb0899_s1_init_1[] = { - - { STB0899_DEV_ID , 0x81 }, - { STB0899_DISCNTRL1 , 0x32 }, - { STB0899_DISCNTRL2 , 0x80 }, - { STB0899_DISRX_ST0 , 0x04 }, - { STB0899_DISRX_ST1 , 0x00 }, - { STB0899_DISPARITY , 0x00 }, - { STB0899_DISSTATUS , 0x20 }, - { STB0899_DISF22 , 0x8c }, - { STB0899_DISF22RX , 0x9a }, - { STB0899_SYSREG , 0x0b }, - { STB0899_ACRPRESC , 0x11 }, - { STB0899_ACRDIV1 , 0x0a }, - { STB0899_ACRDIV2 , 0x05 }, - { STB0899_DACR1 , 0x00 }, - { STB0899_DACR2 , 0x00 }, - { STB0899_OUTCFG , 0x00 }, - { STB0899_MODECFG , 0x00 }, - { STB0899_IRQSTATUS_3 , 0x30 }, - { STB0899_IRQSTATUS_2 , 0x00 }, - { STB0899_IRQSTATUS_1 , 0x00 }, - { STB0899_IRQSTATUS_0 , 0x00 }, - { STB0899_IRQMSK_3 , 0xf3 }, - { STB0899_IRQMSK_2 , 0xfc }, - { STB0899_IRQMSK_1 , 0xff }, - { STB0899_IRQMSK_0 , 0xff }, - { STB0899_IRQCFG , 0x00 }, - { STB0899_I2CCFG , 0x88 }, - { STB0899_I2CRPT , 0x58 }, /* Repeater=8, Stop=disabled */ - { STB0899_IOPVALUE5 , 0x00 }, - { STB0899_IOPVALUE4 , 0x20 }, - { STB0899_IOPVALUE3 , 0xc9 }, - { STB0899_IOPVALUE2 , 0x90 }, - { STB0899_IOPVALUE1 , 0x40 }, - { STB0899_IOPVALUE0 , 0x00 }, - { STB0899_GPIO00CFG , 0x82 }, - { STB0899_GPIO01CFG , 0x82 }, - { STB0899_GPIO02CFG , 0x82 }, - { STB0899_GPIO03CFG , 0x82 }, - { STB0899_GPIO04CFG , 0x82 }, - { STB0899_GPIO05CFG , 0x82 }, - { STB0899_GPIO06CFG , 0x82 }, - { STB0899_GPIO07CFG , 0x82 }, - { STB0899_GPIO08CFG , 0x82 }, - { STB0899_GPIO09CFG , 0x82 }, - { STB0899_GPIO10CFG , 0x82 }, - { STB0899_GPIO11CFG , 0x82 }, - { STB0899_GPIO12CFG , 0x82 }, - { STB0899_GPIO13CFG , 0x82 }, - { STB0899_GPIO14CFG , 0x82 }, - { STB0899_GPIO15CFG , 0x82 }, - { STB0899_GPIO16CFG , 0x82 }, - { STB0899_GPIO17CFG , 0x82 }, - { STB0899_GPIO18CFG , 0x82 }, - { STB0899_GPIO19CFG , 0x82 }, - { STB0899_GPIO20CFG , 0x82 }, - { STB0899_SDATCFG , 0xb8 }, - { STB0899_SCLTCFG , 0xba }, - { STB0899_AGCRFCFG , 0x08 }, /* 0x1c */ - { STB0899_GPIO22 , 0x82 }, /* AGCBB2CFG */ - { STB0899_GPIO21 , 0x91 }, /* AGCBB1CFG */ - { STB0899_DIRCLKCFG , 0x82 }, - { STB0899_CLKOUT27CFG , 0x7e }, - { STB0899_STDBYCFG , 0x82 }, - { STB0899_CS0CFG , 0x82 }, - { STB0899_CS1CFG , 0x82 }, - { STB0899_DISEQCOCFG , 0x20 }, - { STB0899_GPIO32CFG , 0x82 }, - { STB0899_GPIO33CFG , 0x82 }, - { STB0899_GPIO34CFG , 0x82 }, - { STB0899_GPIO35CFG , 0x82 }, - { STB0899_GPIO36CFG , 0x82 }, - { STB0899_GPIO37CFG , 0x82 }, - { STB0899_GPIO38CFG , 0x82 }, - { STB0899_GPIO39CFG , 0x82 }, - { STB0899_NCOARSE , 0x15 }, /* 0x15 = 27 Mhz Clock, F/3 = 198MHz, F/6 = 99MHz */ - { STB0899_SYNTCTRL , 0x02 }, /* 0x00 = CLK from CLKI, 0x02 = CLK from XTALI */ - { STB0899_FILTCTRL , 0x00 }, - { STB0899_SYSCTRL , 0x00 }, - { STB0899_STOPCLK1 , 0x20 }, - { STB0899_STOPCLK2 , 0x00 }, - { STB0899_INTBUFSTATUS , 0x00 }, - { STB0899_INTBUFCTRL , 0x0a }, - { 0xffff , 0xff }, -}; - -static const struct stb0899_s1_reg knc1_stb0899_s1_init_3[] = { - { STB0899_DEMOD , 0x00 }, - { STB0899_RCOMPC , 0xc9 }, - { STB0899_AGC1CN , 0x41 }, - { STB0899_AGC1REF , 0x08 }, - { STB0899_RTC , 0x7a }, - { STB0899_TMGCFG , 0x4e }, - { STB0899_AGC2REF , 0x33 }, - { STB0899_TLSR , 0x84 }, - { STB0899_CFD , 0xee }, - { STB0899_ACLC , 0x87 }, - { STB0899_BCLC , 0x94 }, - { STB0899_EQON , 0x41 }, - { STB0899_LDT , 0xdd }, - { STB0899_LDT2 , 0xc9 }, - { STB0899_EQUALREF , 0xb4 }, - { STB0899_TMGRAMP , 0x10 }, - { STB0899_TMGTHD , 0x30 }, - { STB0899_IDCCOMP , 0xfb }, - { STB0899_QDCCOMP , 0x03 }, - { STB0899_POWERI , 0x3b }, - { STB0899_POWERQ , 0x3d }, - { STB0899_RCOMP , 0x81 }, - { STB0899_AGCIQIN , 0x80 }, - { STB0899_AGC2I1 , 0x04 }, - { STB0899_AGC2I2 , 0xf5 }, - { STB0899_TLIR , 0x25 }, - { STB0899_RTF , 0x80 }, - { STB0899_DSTATUS , 0x00 }, - { STB0899_LDI , 0xca }, - { STB0899_CFRM , 0xf1 }, - { STB0899_CFRL , 0xf3 }, - { STB0899_NIRM , 0x2a }, - { STB0899_NIRL , 0x05 }, - { STB0899_ISYMB , 0x17 }, - { STB0899_QSYMB , 0xfa }, - { STB0899_SFRH , 0x2f }, - { STB0899_SFRM , 0x68 }, - { STB0899_SFRL , 0x40 }, - { STB0899_SFRUPH , 0x2f }, - { STB0899_SFRUPM , 0x68 }, - { STB0899_SFRUPL , 0x40 }, - { STB0899_EQUAI1 , 0xfd }, - { STB0899_EQUAQ1 , 0x04 }, - { STB0899_EQUAI2 , 0x0f }, - { STB0899_EQUAQ2 , 0xff }, - { STB0899_EQUAI3 , 0xdf }, - { STB0899_EQUAQ3 , 0xfa }, - { STB0899_EQUAI4 , 0x37 }, - { STB0899_EQUAQ4 , 0x0d }, - { STB0899_EQUAI5 , 0xbd }, - { STB0899_EQUAQ5 , 0xf7 }, - { STB0899_DSTATUS2 , 0x00 }, - { STB0899_VSTATUS , 0x00 }, - { STB0899_VERROR , 0xff }, - { STB0899_IQSWAP , 0x2a }, - { STB0899_ECNT1M , 0x00 }, - { STB0899_ECNT1L , 0x00 }, - { STB0899_ECNT2M , 0x00 }, - { STB0899_ECNT2L , 0x00 }, - { STB0899_ECNT3M , 0x00 }, - { STB0899_ECNT3L , 0x00 }, - { STB0899_FECAUTO1 , 0x06 }, - { STB0899_FECM , 0x01 }, - { STB0899_VTH12 , 0xf0 }, - { STB0899_VTH23 , 0xa0 }, - { STB0899_VTH34 , 0x78 }, - { STB0899_VTH56 , 0x4e }, - { STB0899_VTH67 , 0x48 }, - { STB0899_VTH78 , 0x38 }, - { STB0899_PRVIT , 0xff }, - { STB0899_VITSYNC , 0x19 }, - { STB0899_RSULC , 0xb1 }, /* DVB = 0xb1, DSS = 0xa1 */ - { STB0899_TSULC , 0x42 }, - { STB0899_RSLLC , 0x40 }, - { STB0899_TSLPL , 0x12 }, - { STB0899_TSCFGH , 0x0c }, - { STB0899_TSCFGM , 0x00 }, - { STB0899_TSCFGL , 0x0c }, - { STB0899_TSOUT , 0x4d }, /* 0x0d for CAM */ - { STB0899_RSSYNCDEL , 0x00 }, - { STB0899_TSINHDELH , 0x02 }, - { STB0899_TSINHDELM , 0x00 }, - { STB0899_TSINHDELL , 0x00 }, - { STB0899_TSLLSTKM , 0x00 }, - { STB0899_TSLLSTKL , 0x00 }, - { STB0899_TSULSTKM , 0x00 }, - { STB0899_TSULSTKL , 0xab }, - { STB0899_PCKLENUL , 0x00 }, - { STB0899_PCKLENLL , 0xcc }, - { STB0899_RSPCKLEN , 0xcc }, - { STB0899_TSSTATUS , 0x80 }, - { STB0899_ERRCTRL1 , 0xb6 }, - { STB0899_ERRCTRL2 , 0x96 }, - { STB0899_ERRCTRL3 , 0x89 }, - { STB0899_DMONMSK1 , 0x27 }, - { STB0899_DMONMSK0 , 0x03 }, - { STB0899_DEMAPVIT , 0x5c }, - { STB0899_PLPARM , 0x1f }, - { STB0899_PDELCTRL , 0x48 }, - { STB0899_PDELCTRL2 , 0x00 }, - { STB0899_BBHCTRL1 , 0x00 }, - { STB0899_BBHCTRL2 , 0x00 }, - { STB0899_HYSTTHRESH , 0x77 }, - { STB0899_MATCSTM , 0x00 }, - { STB0899_MATCSTL , 0x00 }, - { STB0899_UPLCSTM , 0x00 }, - { STB0899_UPLCSTL , 0x00 }, - { STB0899_DFLCSTM , 0x00 }, - { STB0899_DFLCSTL , 0x00 }, - { STB0899_SYNCCST , 0x00 }, - { STB0899_SYNCDCSTM , 0x00 }, - { STB0899_SYNCDCSTL , 0x00 }, - { STB0899_ISI_ENTRY , 0x00 }, - { STB0899_ISI_BIT_EN , 0x00 }, - { STB0899_MATSTRM , 0x00 }, - { STB0899_MATSTRL , 0x00 }, - { STB0899_UPLSTRM , 0x00 }, - { STB0899_UPLSTRL , 0x00 }, - { STB0899_DFLSTRM , 0x00 }, - { STB0899_DFLSTRL , 0x00 }, - { STB0899_SYNCSTR , 0x00 }, - { STB0899_SYNCDSTRM , 0x00 }, - { STB0899_SYNCDSTRL , 0x00 }, - { STB0899_CFGPDELSTATUS1 , 0x10 }, - { STB0899_CFGPDELSTATUS2 , 0x00 }, - { STB0899_BBFERRORM , 0x00 }, - { STB0899_BBFERRORL , 0x00 }, - { STB0899_UPKTERRORM , 0x00 }, - { STB0899_UPKTERRORL , 0x00 }, - { 0xffff , 0xff }, -}; - -/* STB0899 demodulator config for the KNC1 and clones */ -static struct stb0899_config knc1_dvbs2_config = { - .init_dev = knc1_stb0899_s1_init_1, - .init_s2_demod = stb0899_s2_init_2, - .init_s1_demod = knc1_stb0899_s1_init_3, - .init_s2_fec = stb0899_s2_init_4, - .init_tst = stb0899_s1_init_5, - - .postproc = NULL, - - .demod_address = 0x68, -// .ts_output_mode = STB0899_OUT_PARALLEL, /* types = SERIAL/PARALLEL */ - .block_sync_mode = STB0899_SYNC_FORCED, /* DSS, SYNC_FORCED/UNSYNCED */ -// .ts_pfbit_toggle = STB0899_MPEG_NORMAL, /* DirecTV, MPEG toggling seq */ - - .xtal_freq = 27000000, - .inversion = IQ_SWAP_OFF, - - .lo_clk = 76500000, - .hi_clk = 90000000, - - .esno_ave = STB0899_DVBS2_ESNO_AVE, - .esno_quant = STB0899_DVBS2_ESNO_QUANT, - .avframes_coarse = STB0899_DVBS2_AVFRAMES_COARSE, - .avframes_fine = STB0899_DVBS2_AVFRAMES_FINE, - .miss_threshold = STB0899_DVBS2_MISS_THRESHOLD, - .uwp_threshold_acq = STB0899_DVBS2_UWP_THRESHOLD_ACQ, - .uwp_threshold_track = STB0899_DVBS2_UWP_THRESHOLD_TRACK, - .uwp_threshold_sof = STB0899_DVBS2_UWP_THRESHOLD_SOF, - .sof_search_timeout = STB0899_DVBS2_SOF_SEARCH_TIMEOUT, - - .btr_nco_bits = STB0899_DVBS2_BTR_NCO_BITS, - .btr_gain_shift_offset = STB0899_DVBS2_BTR_GAIN_SHIFT_OFFSET, - .crl_nco_bits = STB0899_DVBS2_CRL_NCO_BITS, - .ldpc_max_iter = STB0899_DVBS2_LDPC_MAX_ITER, - - .tuner_get_frequency = tda8261_get_frequency, - .tuner_set_frequency = tda8261_set_frequency, - .tuner_set_bandwidth = NULL, - .tuner_get_bandwidth = tda8261_get_bandwidth, - .tuner_set_rfsiggain = NULL -}; - -/* - * SD1878/SHA tuner config - * 1F, Single I/P, Horizontal mount, High Sensitivity - */ -static const struct tda8261_config sd1878c_config = { -// .name = "SD1878/SHA", - .addr = 0x60, - .step_size = TDA8261_STEP_1000 /* kHz */ -}; - -static u8 read_pwm(struct budget_av *budget_av) -{ - u8 b = 0xff; - u8 pwm; - struct i2c_msg msg[] = { {.addr = 0x50,.flags = 0,.buf = &b,.len = 1}, - {.addr = 0x50,.flags = I2C_M_RD,.buf = &pwm,.len = 1} - }; - - if ((i2c_transfer(&budget_av->budget.i2c_adap, msg, 2) != 2) - || (pwm == 0xff)) - pwm = 0x48; - - return pwm; -} - -#define SUBID_DVBS_KNC1 0x0010 -#define SUBID_DVBS_KNC1_PLUS 0x0011 -#define SUBID_DVBS_TYPHOON 0x4f56 -#define SUBID_DVBS_CINERGY1200 0x1154 -#define SUBID_DVBS_CYNERGY1200N 0x1155 -#define SUBID_DVBS_TV_STAR 0x0014 -#define SUBID_DVBS_TV_STAR_PLUS_X4 0x0015 -#define SUBID_DVBS_TV_STAR_CI 0x0016 -#define SUBID_DVBS2_KNC1 0x0018 -#define SUBID_DVBS2_KNC1_OEM 0x0019 -#define SUBID_DVBS_EASYWATCH_1 0x001a -#define SUBID_DVBS_EASYWATCH_2 0x001b -#define SUBID_DVBS2_EASYWATCH 0x001d -#define SUBID_DVBS_EASYWATCH 0x001e - -#define SUBID_DVBC_EASYWATCH 0x002a -#define SUBID_DVBC_EASYWATCH_MK3 0x002c -#define SUBID_DVBC_KNC1 0x0020 -#define SUBID_DVBC_KNC1_PLUS 0x0021 -#define SUBID_DVBC_KNC1_MK3 0x0022 -#define SUBID_DVBC_KNC1_TDA10024 0x0028 -#define SUBID_DVBC_KNC1_PLUS_MK3 0x0023 -#define SUBID_DVBC_CINERGY1200 0x1156 -#define SUBID_DVBC_CINERGY1200_MK3 0x1176 - -#define SUBID_DVBT_EASYWATCH 0x003a -#define SUBID_DVBT_KNC1_PLUS 0x0031 -#define SUBID_DVBT_KNC1 0x0030 -#define SUBID_DVBT_CINERGY1200 0x1157 - -static void frontend_init(struct budget_av *budget_av) -{ - struct saa7146_dev * saa = budget_av->budget.dev; - struct dvb_frontend * fe = NULL; - - /* Enable / PowerON Frontend */ - saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO); - - /* Wait for PowerON */ - msleep(100); - - /* additional setup necessary for the PLUS cards */ - switch (saa->pci->subsystem_device) { - case SUBID_DVBS_KNC1_PLUS: - case SUBID_DVBC_KNC1_PLUS: - case SUBID_DVBT_KNC1_PLUS: - case SUBID_DVBC_EASYWATCH: - case SUBID_DVBC_KNC1_PLUS_MK3: - case SUBID_DVBS2_KNC1: - case SUBID_DVBS2_KNC1_OEM: - case SUBID_DVBS2_EASYWATCH: - saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTHI); - break; - } - - switch (saa->pci->subsystem_device) { - - case SUBID_DVBS_KNC1: - /* - * maybe that setting is needed for other dvb-s cards as well, - * but so far it has been only confirmed for this type - */ - budget_av->reinitialise_demod = 1; - fallthrough; - case SUBID_DVBS_KNC1_PLUS: - case SUBID_DVBS_EASYWATCH_1: - if (saa->pci->subsystem_vendor == 0x1894) { - fe = dvb_attach(stv0299_attach, &cinergy_1200s_1894_0010_config, - &budget_av->budget.i2c_adap); - if (fe) { - dvb_attach(tua6100_attach, fe, 0x60, &budget_av->budget.i2c_adap); - } - } else { - fe = dvb_attach(stv0299_attach, &typhoon_config, - &budget_av->budget.i2c_adap); - if (fe) { - fe->ops.tuner_ops.set_params = philips_su1278_ty_ci_tuner_set_params; - } - } - break; - - case SUBID_DVBS_TV_STAR: - case SUBID_DVBS_TV_STAR_PLUS_X4: - case SUBID_DVBS_TV_STAR_CI: - case SUBID_DVBS_CYNERGY1200N: - case SUBID_DVBS_EASYWATCH: - case SUBID_DVBS_EASYWATCH_2: - fe = dvb_attach(stv0299_attach, &philips_sd1878_config, - &budget_av->budget.i2c_adap); - if (fe) { - dvb_attach(dvb_pll_attach, fe, 0x60, - &budget_av->budget.i2c_adap, - DVB_PLL_PHILIPS_SD1878_TDA8261); - } - break; - - case SUBID_DVBS_TYPHOON: - fe = dvb_attach(stv0299_attach, &typhoon_config, - &budget_av->budget.i2c_adap); - if (fe) { - fe->ops.tuner_ops.set_params = philips_su1278_ty_ci_tuner_set_params; - } - break; - case SUBID_DVBS2_KNC1: - case SUBID_DVBS2_KNC1_OEM: - case SUBID_DVBS2_EASYWATCH: - budget_av->reinitialise_demod = 1; - if ((fe = dvb_attach(stb0899_attach, &knc1_dvbs2_config, &budget_av->budget.i2c_adap))) - dvb_attach(tda8261_attach, fe, &sd1878c_config, &budget_av->budget.i2c_adap); - - break; - case SUBID_DVBS_CINERGY1200: - fe = dvb_attach(stv0299_attach, &cinergy_1200s_config, - &budget_av->budget.i2c_adap); - if (fe) { - fe->ops.tuner_ops.set_params = philips_su1278_ty_ci_tuner_set_params; - } - break; - - case SUBID_DVBC_KNC1: - case SUBID_DVBC_KNC1_PLUS: - case SUBID_DVBC_CINERGY1200: - case SUBID_DVBC_EASYWATCH: - budget_av->reinitialise_demod = 1; - budget_av->budget.dev->i2c_bitrate = SAA7146_I2C_BUS_BIT_RATE_240; - fe = dvb_attach(tda10021_attach, &philips_cu1216_config, - &budget_av->budget.i2c_adap, - read_pwm(budget_av)); - if (fe == NULL) - fe = dvb_attach(tda10021_attach, &philips_cu1216_config_altaddress, - &budget_av->budget.i2c_adap, - read_pwm(budget_av)); - if (fe) { - fe->ops.tuner_ops.set_params = philips_cu1216_tuner_set_params; - } - break; - - case SUBID_DVBC_EASYWATCH_MK3: - case SUBID_DVBC_CINERGY1200_MK3: - case SUBID_DVBC_KNC1_MK3: - case SUBID_DVBC_KNC1_TDA10024: - case SUBID_DVBC_KNC1_PLUS_MK3: - budget_av->reinitialise_demod = 1; - budget_av->budget.dev->i2c_bitrate = SAA7146_I2C_BUS_BIT_RATE_240; - fe = dvb_attach(tda10023_attach, - &philips_cu1216_tda10023_config, - &budget_av->budget.i2c_adap, - read_pwm(budget_av)); - if (fe) { - fe->ops.tuner_ops.set_params = philips_cu1216_tuner_set_params; - } - break; - - case SUBID_DVBT_EASYWATCH: - case SUBID_DVBT_KNC1: - case SUBID_DVBT_KNC1_PLUS: - case SUBID_DVBT_CINERGY1200: - budget_av->reinitialise_demod = 1; - fe = dvb_attach(tda10046_attach, &philips_tu1216_config, - &budget_av->budget.i2c_adap); - if (fe) { - fe->ops.tuner_ops.init = philips_tu1216_tuner_init; - fe->ops.tuner_ops.set_params = philips_tu1216_tuner_set_params; - } - break; - } - - if (fe == NULL) { - pr_err("A frontend driver was not found for device [%04x:%04x] subsystem [%04x:%04x]\n", - saa->pci->vendor, - saa->pci->device, - saa->pci->subsystem_vendor, - saa->pci->subsystem_device); - return; - } - - budget_av->budget.dvb_frontend = fe; - - if (dvb_register_frontend(&budget_av->budget.dvb_adapter, - budget_av->budget.dvb_frontend)) { - pr_err("Frontend registration failed!\n"); - dvb_frontend_detach(budget_av->budget.dvb_frontend); - budget_av->budget.dvb_frontend = NULL; - } -} - - -static void budget_av_irq(struct saa7146_dev *dev, u32 * isr) -{ - struct budget_av *budget_av = (struct budget_av *) dev->ext_priv; - - dprintk(8, "dev: %p, budget_av: %p\n", dev, budget_av); - - if (*isr & MASK_10) - ttpci_budget_irq10_handler(dev, isr); -} - -static int budget_av_detach(struct saa7146_dev *dev) -{ - struct budget_av *budget_av = (struct budget_av *) dev->ext_priv; - int err; - - dprintk(2, "dev: %p\n", dev); - - if (1 == budget_av->has_saa7113) { - saa7146_setgpio(dev, 0, SAA7146_GPIO_OUTLO); - - msleep(200); - - saa7146_unregister_device(&budget_av->vd, dev); - - saa7146_vv_release(dev); - } - - if (budget_av->budget.ci_present) - ciintf_deinit(budget_av); - - if (budget_av->budget.dvb_frontend != NULL) { - dvb_unregister_frontend(budget_av->budget.dvb_frontend); - dvb_frontend_detach(budget_av->budget.dvb_frontend); - } - err = ttpci_budget_deinit(&budget_av->budget); - - kfree(budget_av); - - return err; -} - -#define KNC1_INPUTS 2 -static struct v4l2_input knc1_inputs[KNC1_INPUTS] = { - { 0, "Composite", V4L2_INPUT_TYPE_TUNER, 1, 0, - V4L2_STD_PAL_BG | V4L2_STD_NTSC_M, 0, V4L2_IN_CAP_STD }, - { 1, "S-Video", V4L2_INPUT_TYPE_CAMERA, 2, 0, - V4L2_STD_PAL_BG | V4L2_STD_NTSC_M, 0, V4L2_IN_CAP_STD }, -}; - -static int vidioc_enum_input(struct file *file, void *fh, struct v4l2_input *i) -{ - dprintk(1, "VIDIOC_ENUMINPUT %d\n", i->index); - if (i->index >= KNC1_INPUTS) - return -EINVAL; - memcpy(i, &knc1_inputs[i->index], sizeof(struct v4l2_input)); - return 0; -} - -static int vidioc_g_input(struct file *file, void *fh, unsigned int *i) -{ - struct saa7146_dev *dev = ((struct saa7146_fh *)fh)->dev; - struct budget_av *budget_av = (struct budget_av *)dev->ext_priv; - - *i = budget_av->cur_input; - - dprintk(1, "VIDIOC_G_INPUT %d\n", *i); - return 0; -} - -static int vidioc_s_input(struct file *file, void *fh, unsigned int input) -{ - struct saa7146_dev *dev = ((struct saa7146_fh *)fh)->dev; - struct budget_av *budget_av = (struct budget_av *)dev->ext_priv; - - dprintk(1, "VIDIOC_S_INPUT %d\n", input); - return saa7113_setinput(budget_av, input); -} - -static struct saa7146_ext_vv vv_data; - -static int budget_av_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info) -{ - struct budget_av *budget_av; - u8 *mac; - int err; - - dprintk(2, "dev: %p\n", dev); - - if (!(budget_av = kzalloc(sizeof(struct budget_av), GFP_KERNEL))) - return -ENOMEM; - - budget_av->has_saa7113 = 0; - budget_av->budget.ci_present = 0; - - dev->ext_priv = budget_av; - - err = ttpci_budget_init(&budget_av->budget, dev, info, THIS_MODULE, - adapter_nr); - if (err) { - kfree(budget_av); - return err; - } - - /* knc1 initialization */ - saa7146_write(dev, DD1_STREAM_B, 0x04000000); - saa7146_write(dev, DD1_INIT, 0x07000600); - saa7146_write(dev, MC2, MASK_09 | MASK_25 | MASK_10 | MASK_26); - - if (saa7113_init(budget_av) == 0) { - budget_av->has_saa7113 = 1; - err = saa7146_vv_init(dev, &vv_data); - if (err != 0) { - /* fixme: proper cleanup here */ - ERR("cannot init vv subsystem\n"); - return err; - } - vv_data.vid_ops.vidioc_enum_input = vidioc_enum_input; - vv_data.vid_ops.vidioc_g_input = vidioc_g_input; - vv_data.vid_ops.vidioc_s_input = vidioc_s_input; - - if ((err = saa7146_register_device(&budget_av->vd, dev, "knc1", VFL_TYPE_VIDEO))) { - /* fixme: proper cleanup here */ - ERR("cannot register capture v4l2 device\n"); - saa7146_vv_release(dev); - return err; - } - - /* beware: this modifies dev->vv ... */ - saa7146_set_hps_source_and_sync(dev, SAA7146_HPS_SOURCE_PORT_A, - SAA7146_HPS_SYNC_PORT_A); - - saa7113_setinput(budget_av, 0); - } - - /* fixme: find some sane values here... */ - saa7146_write(dev, PCI_BT_V1, 0x1c00101f); - - mac = budget_av->budget.dvb_adapter.proposed_mac; - if (i2c_readregs(&budget_av->budget.i2c_adap, 0xa0, 0x30, mac, 6)) { - pr_err("KNC1-%d: Could not read MAC from KNC1 card\n", - budget_av->budget.dvb_adapter.num); - eth_zero_addr(mac); - } else { - pr_info("KNC1-%d: MAC addr = %pM\n", - budget_av->budget.dvb_adapter.num, mac); - } - - budget_av->budget.dvb_adapter.priv = budget_av; - frontend_init(budget_av); - ciintf_init(budget_av); - - ttpci_budget_init_hooks(&budget_av->budget); - - return 0; -} - -static struct saa7146_standard standard[] = { - {.name = "PAL",.id = V4L2_STD_PAL, - .v_offset = 0x17,.v_field = 288, - .h_offset = 0x14,.h_pixels = 680, - .v_max_out = 576,.h_max_out = 768 }, - - {.name = "NTSC",.id = V4L2_STD_NTSC, - .v_offset = 0x16,.v_field = 240, - .h_offset = 0x06,.h_pixels = 708, - .v_max_out = 480,.h_max_out = 640, }, -}; - -static struct saa7146_ext_vv vv_data = { - .inputs = 2, - .capabilities = 0, // perhaps later: V4L2_CAP_VBI_CAPTURE, but that need tweaking with the saa7113 - .flags = 0, - .stds = &standard[0], - .num_stds = ARRAY_SIZE(standard), -}; - -static struct saa7146_extension budget_extension; - -MAKE_BUDGET_INFO(knc1s, "KNC1 DVB-S", BUDGET_KNC1S); -MAKE_BUDGET_INFO(knc1s2,"KNC1 DVB-S2", BUDGET_KNC1S2); -MAKE_BUDGET_INFO(sates2,"Satelco EasyWatch DVB-S2", BUDGET_KNC1S2); -MAKE_BUDGET_INFO(knc1c, "KNC1 DVB-C", BUDGET_KNC1C); -MAKE_BUDGET_INFO(knc1t, "KNC1 DVB-T", BUDGET_KNC1T); -MAKE_BUDGET_INFO(kncxs, "KNC TV STAR DVB-S", BUDGET_TVSTAR); -MAKE_BUDGET_INFO(satewpls, "Satelco EasyWatch DVB-S light", BUDGET_TVSTAR); -MAKE_BUDGET_INFO(satewpls1, "Satelco EasyWatch DVB-S light", BUDGET_KNC1S); -MAKE_BUDGET_INFO(satewps, "Satelco EasyWatch DVB-S", BUDGET_KNC1S); -MAKE_BUDGET_INFO(satewplc, "Satelco EasyWatch DVB-C", BUDGET_KNC1CP); -MAKE_BUDGET_INFO(satewcmk3, "Satelco EasyWatch DVB-C MK3", BUDGET_KNC1C_MK3); -MAKE_BUDGET_INFO(satewt, "Satelco EasyWatch DVB-T", BUDGET_KNC1T); -MAKE_BUDGET_INFO(knc1sp, "KNC1 DVB-S Plus", BUDGET_KNC1SP); -MAKE_BUDGET_INFO(knc1spx4, "KNC1 DVB-S Plus X4", BUDGET_KNC1SP); -MAKE_BUDGET_INFO(knc1cp, "KNC1 DVB-C Plus", BUDGET_KNC1CP); -MAKE_BUDGET_INFO(knc1cmk3, "KNC1 DVB-C MK3", BUDGET_KNC1C_MK3); -MAKE_BUDGET_INFO(knc1ctda10024, "KNC1 DVB-C TDA10024", BUDGET_KNC1C_TDA10024); -MAKE_BUDGET_INFO(knc1cpmk3, "KNC1 DVB-C Plus MK3", BUDGET_KNC1CP_MK3); -MAKE_BUDGET_INFO(knc1tp, "KNC1 DVB-T Plus", BUDGET_KNC1TP); -MAKE_BUDGET_INFO(cin1200s, "TerraTec Cinergy 1200 DVB-S", BUDGET_CIN1200S); -MAKE_BUDGET_INFO(cin1200sn, "TerraTec Cinergy 1200 DVB-S", BUDGET_CIN1200S); -MAKE_BUDGET_INFO(cin1200c, "Terratec Cinergy 1200 DVB-C", BUDGET_CIN1200C); -MAKE_BUDGET_INFO(cin1200cmk3, "Terratec Cinergy 1200 DVB-C MK3", BUDGET_CIN1200C_MK3); -MAKE_BUDGET_INFO(cin1200t, "Terratec Cinergy 1200 DVB-T", BUDGET_CIN1200T); - -static const struct pci_device_id pci_tbl[] = { - MAKE_EXTENSION_PCI(knc1s, 0x1131, 0x4f56), - MAKE_EXTENSION_PCI(knc1s, 0x1131, 0x0010), - MAKE_EXTENSION_PCI(knc1s, 0x1894, 0x0010), - MAKE_EXTENSION_PCI(knc1sp, 0x1131, 0x0011), - MAKE_EXTENSION_PCI(knc1sp, 0x1894, 0x0011), - MAKE_EXTENSION_PCI(kncxs, 0x1894, 0x0014), - MAKE_EXTENSION_PCI(knc1spx4, 0x1894, 0x0015), - MAKE_EXTENSION_PCI(kncxs, 0x1894, 0x0016), - MAKE_EXTENSION_PCI(knc1s2, 0x1894, 0x0018), - MAKE_EXTENSION_PCI(knc1s2, 0x1894, 0x0019), - MAKE_EXTENSION_PCI(sates2, 0x1894, 0x001d), - MAKE_EXTENSION_PCI(satewpls, 0x1894, 0x001e), - MAKE_EXTENSION_PCI(satewpls1, 0x1894, 0x001a), - MAKE_EXTENSION_PCI(satewps, 0x1894, 0x001b), - MAKE_EXTENSION_PCI(satewplc, 0x1894, 0x002a), - MAKE_EXTENSION_PCI(satewcmk3, 0x1894, 0x002c), - MAKE_EXTENSION_PCI(satewt, 0x1894, 0x003a), - MAKE_EXTENSION_PCI(knc1c, 0x1894, 0x0020), - MAKE_EXTENSION_PCI(knc1cp, 0x1894, 0x0021), - MAKE_EXTENSION_PCI(knc1cmk3, 0x1894, 0x0022), - MAKE_EXTENSION_PCI(knc1ctda10024, 0x1894, 0x0028), - MAKE_EXTENSION_PCI(knc1cpmk3, 0x1894, 0x0023), - MAKE_EXTENSION_PCI(knc1t, 0x1894, 0x0030), - MAKE_EXTENSION_PCI(knc1tp, 0x1894, 0x0031), - MAKE_EXTENSION_PCI(cin1200s, 0x153b, 0x1154), - MAKE_EXTENSION_PCI(cin1200sn, 0x153b, 0x1155), - MAKE_EXTENSION_PCI(cin1200c, 0x153b, 0x1156), - MAKE_EXTENSION_PCI(cin1200cmk3, 0x153b, 0x1176), - MAKE_EXTENSION_PCI(cin1200t, 0x153b, 0x1157), - { - .vendor = 0, - } -}; - -MODULE_DEVICE_TABLE(pci, pci_tbl); - -static struct saa7146_extension budget_extension = { - .name = "budget_av", - .flags = SAA7146_USE_I2C_IRQ, - - .pci_tbl = pci_tbl, - - .module = THIS_MODULE, - .attach = budget_av_attach, - .detach = budget_av_detach, - - .irq_mask = MASK_10, - .irq_func = budget_av_irq, -}; - -static int __init budget_av_init(void) -{ - return saa7146_register_extension(&budget_extension); -} - -static void __exit budget_av_exit(void) -{ - saa7146_unregister_extension(&budget_extension); -} - -module_init(budget_av_init); -module_exit(budget_av_exit); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Ralph Metzler, Marcus Metzler, Michael Hunold, others"); -MODULE_DESCRIPTION("driver for the SAA7146 based so-called budget PCI DVB w/ analog input and CI-module (e.g. the KNC cards)"); diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/budget-ci.c b/drivers/staging/media/deprecated/saa7146/ttpci/budget-ci.c deleted file mode 100644 index d59d18647371..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/budget-ci.c +++ /dev/null @@ -1,1574 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * budget-ci.c: driver for the SAA7146 based Budget DVB cards - * - * Compiled from various sources by Michael Hunold <michael@xxxxxxx> - * - * msp430 IR support contributed by Jack Thomasson <jkt@xxxxxxxxxx> - * partially based on the Siemens DVB driver by Ralph+Marcus Metzler - * - * CI interface support (c) 2004 Andrew de Quincey <adq_dvb@xxxxxxxxxxxxx> - * - * the project's page is at https://linuxtv.org - */ - -#include <linux/module.h> -#include <linux/errno.h> -#include <linux/slab.h> -#include <linux/interrupt.h> -#include <linux/spinlock.h> -#include <media/rc-core.h> - -#include "budget.h" - -#include <media/dvb_ca_en50221.h> -#include "stv0299.h" -#include "stv0297.h" -#include "tda1004x.h" -#include "stb0899_drv.h" -#include "stb0899_reg.h" -#include "stb0899_cfg.h" -#include "stb6100.h" -#include "stb6100_cfg.h" -#include "lnbp21.h" -#include "bsbe1.h" -#include "bsru6.h" -#include "tda1002x.h" -#include "tda827x.h" -#include "bsbe1-d01a.h" - -#define MODULE_NAME "budget_ci" - -/* - * Regarding DEBIADDR_IR: - * Some CI modules hang if random addresses are read. - * Using address 0x4000 for the IR read means that we - * use the same address as for CI version, which should - * be a safe default. - */ -#define DEBIADDR_IR 0x4000 -#define DEBIADDR_CICONTROL 0x0000 -#define DEBIADDR_CIVERSION 0x4000 -#define DEBIADDR_IO 0x1000 -#define DEBIADDR_ATTR 0x3000 - -#define CICONTROL_RESET 0x01 -#define CICONTROL_ENABLETS 0x02 -#define CICONTROL_CAMDETECT 0x08 - -#define DEBICICTL 0x00420000 -#define DEBICICAM 0x02420000 - -#define SLOTSTATUS_NONE 1 -#define SLOTSTATUS_PRESENT 2 -#define SLOTSTATUS_RESET 4 -#define SLOTSTATUS_READY 8 -#define SLOTSTATUS_OCCUPIED (SLOTSTATUS_PRESENT|SLOTSTATUS_RESET|SLOTSTATUS_READY) - -/* RC5 device wildcard */ -#define IR_DEVICE_ANY 255 - -static int rc5_device = -1; -module_param(rc5_device, int, 0644); -MODULE_PARM_DESC(rc5_device, "only IR commands to given RC5 device (device = 0 - 31, any device = 255, default: autodetect)"); - -static int ir_debug; -module_param(ir_debug, int, 0644); -MODULE_PARM_DESC(ir_debug, "enable debugging information for IR decoding"); - -DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); - -struct budget_ci_ir { - struct rc_dev *dev; - struct tasklet_struct msp430_irq_tasklet; - char name[72]; /* 40 + 32 for (struct saa7146_dev).name */ - char phys[32]; - int rc5_device; - u32 ir_key; - bool have_command; - bool full_rc5; /* Outputs a full RC5 code */ -}; - -struct budget_ci { - struct budget budget; - struct tasklet_struct ciintf_irq_tasklet; - int slot_status; - int ci_irq; - struct dvb_ca_en50221 ca; - struct budget_ci_ir ir; - u8 tuner_pll_address; /* used for philips_tdm1316l configs */ -}; - -static void msp430_ir_interrupt(struct tasklet_struct *t) -{ - struct budget_ci_ir *ir = from_tasklet(ir, t, msp430_irq_tasklet); - struct budget_ci *budget_ci = container_of(ir, typeof(*budget_ci), ir); - struct rc_dev *dev = budget_ci->ir.dev; - u32 command = ttpci_budget_debiread(&budget_ci->budget, DEBINOSWAP, DEBIADDR_IR, 2, 1, 0) >> 8; - - /* - * The msp430 chip can generate two different bytes, command and device - * - * type1: X1CCCCCC, C = command bits (0 - 63) - * type2: X0TDDDDD, D = device bits (0 - 31), T = RC5 toggle bit - * - * Each signal from the remote control can generate one or more command - * bytes and one or more device bytes. For the repeated bytes, the - * highest bit (X) is set. The first command byte is always generated - * before the first device byte. Other than that, no specific order - * seems to apply. To make life interesting, bytes can also be lost. - * - * Only when we have a command and device byte, a keypress is - * generated. - */ - - if (ir_debug) - printk("budget_ci: received byte 0x%02x\n", command); - - /* Remove repeat bit, we use every command */ - command = command & 0x7f; - - /* Is this a RC5 command byte? */ - if (command & 0x40) { - budget_ci->ir.have_command = true; - budget_ci->ir.ir_key = command & 0x3f; - return; - } - - /* It's a RC5 device byte */ - if (!budget_ci->ir.have_command) - return; - budget_ci->ir.have_command = false; - - if (budget_ci->ir.rc5_device != IR_DEVICE_ANY && - budget_ci->ir.rc5_device != (command & 0x1f)) - return; - - if (budget_ci->ir.full_rc5) { - rc_keydown(dev, RC_PROTO_RC5, - RC_SCANCODE_RC5(budget_ci->ir.rc5_device, budget_ci->ir.ir_key), - !!(command & 0x20)); - return; - } - - /* FIXME: We should generate complete scancodes for all devices */ - rc_keydown(dev, RC_PROTO_UNKNOWN, budget_ci->ir.ir_key, - !!(command & 0x20)); -} - -static int msp430_ir_init(struct budget_ci *budget_ci) -{ - struct saa7146_dev *saa = budget_ci->budget.dev; - struct rc_dev *dev; - int error; - - dev = rc_allocate_device(RC_DRIVER_SCANCODE); - if (!dev) { - printk(KERN_ERR "budget_ci: IR interface initialisation failed\n"); - return -ENOMEM; - } - - snprintf(budget_ci->ir.name, sizeof(budget_ci->ir.name), - "Budget-CI dvb ir receiver %s", saa->name); - snprintf(budget_ci->ir.phys, sizeof(budget_ci->ir.phys), - "pci-%s/ir0", pci_name(saa->pci)); - - dev->driver_name = MODULE_NAME; - dev->device_name = budget_ci->ir.name; - dev->input_phys = budget_ci->ir.phys; - dev->input_id.bustype = BUS_PCI; - dev->input_id.version = 1; - if (saa->pci->subsystem_vendor) { - dev->input_id.vendor = saa->pci->subsystem_vendor; - dev->input_id.product = saa->pci->subsystem_device; - } else { - dev->input_id.vendor = saa->pci->vendor; - dev->input_id.product = saa->pci->device; - } - dev->dev.parent = &saa->pci->dev; - - if (rc5_device < 0) - budget_ci->ir.rc5_device = IR_DEVICE_ANY; - else - budget_ci->ir.rc5_device = rc5_device; - - /* Select keymap and address */ - switch (budget_ci->budget.dev->pci->subsystem_device) { - case 0x100c: - case 0x100f: - case 0x1011: - case 0x1012: - /* The hauppauge keymap is a superset of these remotes */ - dev->map_name = RC_MAP_HAUPPAUGE; - budget_ci->ir.full_rc5 = true; - - if (rc5_device < 0) - budget_ci->ir.rc5_device = 0x1f; - break; - case 0x1010: - case 0x1017: - case 0x1019: - case 0x101a: - case 0x101b: - /* for the Technotrend 1500 bundled remote */ - dev->map_name = RC_MAP_TT_1500; - break; - default: - /* unknown remote */ - dev->map_name = RC_MAP_BUDGET_CI_OLD; - break; - } - if (!budget_ci->ir.full_rc5) - dev->scancode_mask = 0xff; - - error = rc_register_device(dev); - if (error) { - printk(KERN_ERR "budget_ci: could not init driver for IR device (code %d)\n", error); - rc_free_device(dev); - return error; - } - - budget_ci->ir.dev = dev; - - tasklet_setup(&budget_ci->ir.msp430_irq_tasklet, msp430_ir_interrupt); - - SAA7146_IER_ENABLE(saa, MASK_06); - saa7146_setgpio(saa, 3, SAA7146_GPIO_IRQHI); - - return 0; -} - -static void msp430_ir_deinit(struct budget_ci *budget_ci) -{ - struct saa7146_dev *saa = budget_ci->budget.dev; - - SAA7146_IER_DISABLE(saa, MASK_06); - saa7146_setgpio(saa, 3, SAA7146_GPIO_INPUT); - tasklet_kill(&budget_ci->ir.msp430_irq_tasklet); - - rc_unregister_device(budget_ci->ir.dev); -} - -static int ciintf_read_attribute_mem(struct dvb_ca_en50221 *ca, int slot, int address) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - - if (slot != 0) - return -EINVAL; - - return ttpci_budget_debiread(&budget_ci->budget, DEBICICAM, - DEBIADDR_ATTR | (address & 0xfff), 1, 1, 0); -} - -static int ciintf_write_attribute_mem(struct dvb_ca_en50221 *ca, int slot, int address, u8 value) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - - if (slot != 0) - return -EINVAL; - - return ttpci_budget_debiwrite(&budget_ci->budget, DEBICICAM, - DEBIADDR_ATTR | (address & 0xfff), 1, value, 1, 0); -} - -static int ciintf_read_cam_control(struct dvb_ca_en50221 *ca, int slot, u8 address) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - - if (slot != 0) - return -EINVAL; - - return ttpci_budget_debiread(&budget_ci->budget, DEBICICAM, - DEBIADDR_IO | (address & 3), 1, 1, 0); -} - -static int ciintf_write_cam_control(struct dvb_ca_en50221 *ca, int slot, u8 address, u8 value) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - - if (slot != 0) - return -EINVAL; - - return ttpci_budget_debiwrite(&budget_ci->budget, DEBICICAM, - DEBIADDR_IO | (address & 3), 1, value, 1, 0); -} - -static int ciintf_slot_reset(struct dvb_ca_en50221 *ca, int slot) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - struct saa7146_dev *saa = budget_ci->budget.dev; - - if (slot != 0) - return -EINVAL; - - if (budget_ci->ci_irq) { - // trigger on RISING edge during reset so we know when READY is re-asserted - saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQHI); - } - budget_ci->slot_status = SLOTSTATUS_RESET; - ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 0, 1, 0); - msleep(1); - ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, - CICONTROL_RESET, 1, 0); - - saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTHI); - ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB); - return 0; -} - -static int ciintf_slot_shutdown(struct dvb_ca_en50221 *ca, int slot) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - struct saa7146_dev *saa = budget_ci->budget.dev; - - if (slot != 0) - return -EINVAL; - - saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTHI); - ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB); - return 0; -} - -static int ciintf_slot_ts_enable(struct dvb_ca_en50221 *ca, int slot) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - struct saa7146_dev *saa = budget_ci->budget.dev; - int tmp; - - if (slot != 0) - return -EINVAL; - - saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTLO); - - tmp = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0); - ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, - tmp | CICONTROL_ENABLETS, 1, 0); - - ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTA); - return 0; -} - -static void ciintf_interrupt(struct tasklet_struct *t) -{ - struct budget_ci *budget_ci = from_tasklet(budget_ci, t, - ciintf_irq_tasklet); - struct saa7146_dev *saa = budget_ci->budget.dev; - unsigned int flags; - - // ensure we don't get spurious IRQs during initialisation - if (!budget_ci->budget.ci_present) - return; - - // read the CAM status - flags = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0); - if (flags & CICONTROL_CAMDETECT) { - - // GPIO should be set to trigger on falling edge if a CAM is present - saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQLO); - - if (budget_ci->slot_status & SLOTSTATUS_NONE) { - // CAM insertion IRQ - budget_ci->slot_status = SLOTSTATUS_PRESENT; - dvb_ca_en50221_camchange_irq(&budget_ci->ca, 0, - DVB_CA_EN50221_CAMCHANGE_INSERTED); - - } else if (budget_ci->slot_status & SLOTSTATUS_RESET) { - // CAM ready (reset completed) - budget_ci->slot_status = SLOTSTATUS_READY; - dvb_ca_en50221_camready_irq(&budget_ci->ca, 0); - - } else if (budget_ci->slot_status & SLOTSTATUS_READY) { - // FR/DA IRQ - dvb_ca_en50221_frda_irq(&budget_ci->ca, 0); - } - } else { - - // trigger on rising edge if a CAM is not present - when a CAM is inserted, we - // only want to get the IRQ when it sets READY. If we trigger on the falling edge, - // the CAM might not actually be ready yet. - saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQHI); - - // generate a CAM removal IRQ if we haven't already - if (budget_ci->slot_status & SLOTSTATUS_OCCUPIED) { - // CAM removal IRQ - budget_ci->slot_status = SLOTSTATUS_NONE; - dvb_ca_en50221_camchange_irq(&budget_ci->ca, 0, - DVB_CA_EN50221_CAMCHANGE_REMOVED); - } - } -} - -static int ciintf_poll_slot_status(struct dvb_ca_en50221 *ca, int slot, int open) -{ - struct budget_ci *budget_ci = (struct budget_ci *) ca->data; - unsigned int flags; - - // ensure we don't get spurious IRQs during initialisation - if (!budget_ci->budget.ci_present) - return -EINVAL; - - // read the CAM status - flags = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0); - if (flags & CICONTROL_CAMDETECT) { - // mark it as present if it wasn't before - if (budget_ci->slot_status & SLOTSTATUS_NONE) { - budget_ci->slot_status = SLOTSTATUS_PRESENT; - } - - // during a RESET, we check if we can read from IO memory to see when CAM is ready - if (budget_ci->slot_status & SLOTSTATUS_RESET) { - if (ciintf_read_attribute_mem(ca, slot, 0) == 0x1d) { - budget_ci->slot_status = SLOTSTATUS_READY; - } - } - } else { - budget_ci->slot_status = SLOTSTATUS_NONE; - } - - if (budget_ci->slot_status != SLOTSTATUS_NONE) { - if (budget_ci->slot_status & SLOTSTATUS_READY) { - return DVB_CA_EN50221_POLL_CAM_PRESENT | DVB_CA_EN50221_POLL_CAM_READY; - } - return DVB_CA_EN50221_POLL_CAM_PRESENT; - } - - return 0; -} - -static int ciintf_init(struct budget_ci *budget_ci) -{ - struct saa7146_dev *saa = budget_ci->budget.dev; - int flags; - int result; - int ci_version; - int ca_flags; - - memset(&budget_ci->ca, 0, sizeof(struct dvb_ca_en50221)); - - // enable DEBI pins - saa7146_write(saa, MC1, MASK_27 | MASK_11); - - // test if it is there - ci_version = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CIVERSION, 1, 1, 0); - if ((ci_version & 0xa0) != 0xa0) { - result = -ENODEV; - goto error; - } - - // determine whether a CAM is present or not - flags = ttpci_budget_debiread(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 1, 0); - budget_ci->slot_status = SLOTSTATUS_NONE; - if (flags & CICONTROL_CAMDETECT) - budget_ci->slot_status = SLOTSTATUS_PRESENT; - - // version 0xa2 of the CI firmware doesn't generate interrupts - if (ci_version == 0xa2) { - ca_flags = 0; - budget_ci->ci_irq = 0; - } else { - ca_flags = DVB_CA_EN50221_FLAG_IRQ_CAMCHANGE | - DVB_CA_EN50221_FLAG_IRQ_FR | - DVB_CA_EN50221_FLAG_IRQ_DA; - budget_ci->ci_irq = 1; - } - - // register CI interface - budget_ci->ca.owner = THIS_MODULE; - budget_ci->ca.read_attribute_mem = ciintf_read_attribute_mem; - budget_ci->ca.write_attribute_mem = ciintf_write_attribute_mem; - budget_ci->ca.read_cam_control = ciintf_read_cam_control; - budget_ci->ca.write_cam_control = ciintf_write_cam_control; - budget_ci->ca.slot_reset = ciintf_slot_reset; - budget_ci->ca.slot_shutdown = ciintf_slot_shutdown; - budget_ci->ca.slot_ts_enable = ciintf_slot_ts_enable; - budget_ci->ca.poll_slot_status = ciintf_poll_slot_status; - budget_ci->ca.data = budget_ci; - if ((result = dvb_ca_en50221_init(&budget_ci->budget.dvb_adapter, - &budget_ci->ca, - ca_flags, 1)) != 0) { - printk("budget_ci: CI interface detected, but initialisation failed.\n"); - goto error; - } - - // Setup CI slot IRQ - if (budget_ci->ci_irq) { - tasklet_setup(&budget_ci->ciintf_irq_tasklet, ciintf_interrupt); - if (budget_ci->slot_status != SLOTSTATUS_NONE) { - saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQLO); - } else { - saa7146_setgpio(saa, 0, SAA7146_GPIO_IRQHI); - } - SAA7146_IER_ENABLE(saa, MASK_03); - } - - // enable interface - ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, - CICONTROL_RESET, 1, 0); - - // success! - printk("budget_ci: CI interface initialised\n"); - budget_ci->budget.ci_present = 1; - - // forge a fake CI IRQ so the CAM state is setup correctly - if (budget_ci->ci_irq) { - flags = DVB_CA_EN50221_CAMCHANGE_REMOVED; - if (budget_ci->slot_status != SLOTSTATUS_NONE) - flags = DVB_CA_EN50221_CAMCHANGE_INSERTED; - dvb_ca_en50221_camchange_irq(&budget_ci->ca, 0, flags); - } - - return 0; - -error: - saa7146_write(saa, MC1, MASK_27); - return result; -} - -static void ciintf_deinit(struct budget_ci *budget_ci) -{ - struct saa7146_dev *saa = budget_ci->budget.dev; - - // disable CI interrupts - if (budget_ci->ci_irq) { - SAA7146_IER_DISABLE(saa, MASK_03); - saa7146_setgpio(saa, 0, SAA7146_GPIO_INPUT); - tasklet_kill(&budget_ci->ciintf_irq_tasklet); - } - - // reset interface - ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, 0, 1, 0); - msleep(1); - ttpci_budget_debiwrite(&budget_ci->budget, DEBICICTL, DEBIADDR_CICONTROL, 1, - CICONTROL_RESET, 1, 0); - - // disable TS data stream to CI interface - saa7146_setgpio(saa, 1, SAA7146_GPIO_INPUT); - - // release the CA device - dvb_ca_en50221_release(&budget_ci->ca); - - // disable DEBI pins - saa7146_write(saa, MC1, MASK_27); -} - -static void budget_ci_irq(struct saa7146_dev *dev, u32 * isr) -{ - struct budget_ci *budget_ci = (struct budget_ci *) dev->ext_priv; - - dprintk(8, "dev: %p, budget_ci: %p\n", dev, budget_ci); - - if (*isr & MASK_06) - tasklet_schedule(&budget_ci->ir.msp430_irq_tasklet); - - if (*isr & MASK_10) - ttpci_budget_irq10_handler(dev, isr); - - if ((*isr & MASK_03) && (budget_ci->budget.ci_present) && (budget_ci->ci_irq)) - tasklet_schedule(&budget_ci->ciintf_irq_tasklet); -} - -static u8 philips_su1278_tt_inittab[] = { - 0x01, 0x0f, - 0x02, 0x30, - 0x03, 0x00, - 0x04, 0x5b, - 0x05, 0x85, - 0x06, 0x02, - 0x07, 0x00, - 0x08, 0x02, - 0x09, 0x00, - 0x0C, 0x01, - 0x0D, 0x81, - 0x0E, 0x44, - 0x0f, 0x14, - 0x10, 0x3c, - 0x11, 0x84, - 0x12, 0xda, - 0x13, 0x97, - 0x14, 0x95, - 0x15, 0xc9, - 0x16, 0x19, - 0x17, 0x8c, - 0x18, 0x59, - 0x19, 0xf8, - 0x1a, 0xfe, - 0x1c, 0x7f, - 0x1d, 0x00, - 0x1e, 0x00, - 0x1f, 0x50, - 0x20, 0x00, - 0x21, 0x00, - 0x22, 0x00, - 0x23, 0x00, - 0x28, 0x00, - 0x29, 0x28, - 0x2a, 0x14, - 0x2b, 0x0f, - 0x2c, 0x09, - 0x2d, 0x09, - 0x31, 0x1f, - 0x32, 0x19, - 0x33, 0xfc, - 0x34, 0x93, - 0xff, 0xff -}; - -static int philips_su1278_tt_set_symbol_rate(struct dvb_frontend *fe, u32 srate, u32 ratio) -{ - stv0299_writereg(fe, 0x0e, 0x44); - if (srate >= 10000000) { - stv0299_writereg(fe, 0x13, 0x97); - stv0299_writereg(fe, 0x14, 0x95); - stv0299_writereg(fe, 0x15, 0xc9); - stv0299_writereg(fe, 0x17, 0x8c); - stv0299_writereg(fe, 0x1a, 0xfe); - stv0299_writereg(fe, 0x1c, 0x7f); - stv0299_writereg(fe, 0x2d, 0x09); - } else { - stv0299_writereg(fe, 0x13, 0x99); - stv0299_writereg(fe, 0x14, 0x8d); - stv0299_writereg(fe, 0x15, 0xce); - stv0299_writereg(fe, 0x17, 0x43); - stv0299_writereg(fe, 0x1a, 0x1d); - stv0299_writereg(fe, 0x1c, 0x12); - stv0299_writereg(fe, 0x2d, 0x05); - } - stv0299_writereg(fe, 0x0e, 0x23); - stv0299_writereg(fe, 0x0f, 0x94); - stv0299_writereg(fe, 0x10, 0x39); - stv0299_writereg(fe, 0x15, 0xc9); - - stv0299_writereg(fe, 0x1f, (ratio >> 16) & 0xff); - stv0299_writereg(fe, 0x20, (ratio >> 8) & 0xff); - stv0299_writereg(fe, 0x21, (ratio) & 0xf0); - - return 0; -} - -static int philips_su1278_tt_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *p = &fe->dtv_property_cache; - struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv; - u32 div; - u8 buf[4]; - struct i2c_msg msg = {.addr = 0x60,.flags = 0,.buf = buf,.len = sizeof(buf) }; - - if ((p->frequency < 950000) || (p->frequency > 2150000)) - return -EINVAL; - - div = (p->frequency + (500 - 1)) / 500; /* round correctly */ - buf[0] = (div >> 8) & 0x7f; - buf[1] = div & 0xff; - buf[2] = 0x80 | ((div & 0x18000) >> 10) | 2; - buf[3] = 0x20; - - if (p->symbol_rate < 4000000) - buf[3] |= 1; - - if (p->frequency < 1250000) - buf[3] |= 0; - else if (p->frequency < 1550000) - buf[3] |= 0x40; - else if (p->frequency < 2050000) - buf[3] |= 0x80; - else if (p->frequency < 2150000) - buf[3] |= 0xC0; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget_ci->budget.i2c_adap, &msg, 1) != 1) - return -EIO; - return 0; -} - -static const struct stv0299_config philips_su1278_tt_config = { - - .demod_address = 0x68, - .inittab = philips_su1278_tt_inittab, - .mclk = 64000000UL, - .invert = 0, - .skip_reinit = 1, - .lock_output = STV0299_LOCKOUTPUT_1, - .volt13_op0_op1 = STV0299_VOLT13_OP1, - .min_delay_ms = 50, - .set_symbol_rate = philips_su1278_tt_set_symbol_rate, -}; - - - -static int philips_tdm1316l_tuner_init(struct dvb_frontend *fe) -{ - struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv; - static u8 td1316_init[] = { 0x0b, 0xf5, 0x85, 0xab }; - static u8 disable_mc44BC374c[] = { 0x1d, 0x74, 0xa0, 0x68 }; - struct i2c_msg tuner_msg = {.addr = budget_ci->tuner_pll_address,.flags = 0,.buf = td1316_init,.len = - sizeof(td1316_init) }; - - // setup PLL configuration - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1) - return -EIO; - msleep(1); - - // disable the mc44BC374c (do not check for errors) - tuner_msg.addr = 0x65; - tuner_msg.buf = disable_mc44BC374c; - tuner_msg.len = sizeof(disable_mc44BC374c); - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1) { - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1); - } - - return 0; -} - -static int philips_tdm1316l_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *p = &fe->dtv_property_cache; - struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv; - u8 tuner_buf[4]; - struct i2c_msg tuner_msg = {.addr = budget_ci->tuner_pll_address,.flags = 0,.buf = tuner_buf,.len = sizeof(tuner_buf) }; - int tuner_frequency = 0; - u8 band, cp, filter; - - // determine charge pump - tuner_frequency = p->frequency + 36130000; - if (tuner_frequency < 87000000) - return -EINVAL; - else if (tuner_frequency < 130000000) - cp = 3; - else if (tuner_frequency < 160000000) - cp = 5; - else if (tuner_frequency < 200000000) - cp = 6; - else if (tuner_frequency < 290000000) - cp = 3; - else if (tuner_frequency < 420000000) - cp = 5; - else if (tuner_frequency < 480000000) - cp = 6; - else if (tuner_frequency < 620000000) - cp = 3; - else if (tuner_frequency < 830000000) - cp = 5; - else if (tuner_frequency < 895000000) - cp = 7; - else - return -EINVAL; - - // determine band - if (p->frequency < 49000000) - return -EINVAL; - else if (p->frequency < 159000000) - band = 1; - else if (p->frequency < 444000000) - band = 2; - else if (p->frequency < 861000000) - band = 4; - else - return -EINVAL; - - // setup PLL filter and TDA9889 - switch (p->bandwidth_hz) { - case 6000000: - tda1004x_writereg(fe, 0x0C, 0x14); - filter = 0; - break; - - case 7000000: - tda1004x_writereg(fe, 0x0C, 0x80); - filter = 0; - break; - - case 8000000: - tda1004x_writereg(fe, 0x0C, 0x14); - filter = 1; - break; - - default: - return -EINVAL; - } - - // calculate divisor - // ((36130000+((1000000/6)/2)) + Finput)/(1000000/6) - tuner_frequency = (((p->frequency / 1000) * 6) + 217280) / 1000; - - // setup tuner buffer - tuner_buf[0] = tuner_frequency >> 8; - tuner_buf[1] = tuner_frequency & 0xff; - tuner_buf[2] = 0xca; - tuner_buf[3] = (cp << 5) | (filter << 3) | band; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1) - return -EIO; - - msleep(1); - return 0; -} - -static int philips_tdm1316l_request_firmware(struct dvb_frontend *fe, - const struct firmware **fw, char *name) -{ - struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv; - - return request_firmware(fw, name, &budget_ci->budget.dev->pci->dev); -} - -static struct tda1004x_config philips_tdm1316l_config = { - - .demod_address = 0x8, - .invert = 0, - .invert_oclk = 0, - .xtal_freq = TDA10046_XTAL_4M, - .agc_config = TDA10046_AGC_DEFAULT, - .if_freq = TDA10046_FREQ_3617, - .request_firmware = philips_tdm1316l_request_firmware, -}; - -static struct tda1004x_config philips_tdm1316l_config_invert = { - - .demod_address = 0x8, - .invert = 1, - .invert_oclk = 0, - .xtal_freq = TDA10046_XTAL_4M, - .agc_config = TDA10046_AGC_DEFAULT, - .if_freq = TDA10046_FREQ_3617, - .request_firmware = philips_tdm1316l_request_firmware, -}; - -static int dvbc_philips_tdm1316l_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *p = &fe->dtv_property_cache; - struct budget_ci *budget_ci = (struct budget_ci *) fe->dvb->priv; - u8 tuner_buf[5]; - struct i2c_msg tuner_msg = {.addr = budget_ci->tuner_pll_address, - .flags = 0, - .buf = tuner_buf, - .len = sizeof(tuner_buf) }; - int tuner_frequency = 0; - u8 band, cp, filter; - - // determine charge pump - tuner_frequency = p->frequency + 36125000; - if (tuner_frequency < 87000000) - return -EINVAL; - else if (tuner_frequency < 130000000) { - cp = 3; - band = 1; - } else if (tuner_frequency < 160000000) { - cp = 5; - band = 1; - } else if (tuner_frequency < 200000000) { - cp = 6; - band = 1; - } else if (tuner_frequency < 290000000) { - cp = 3; - band = 2; - } else if (tuner_frequency < 420000000) { - cp = 5; - band = 2; - } else if (tuner_frequency < 480000000) { - cp = 6; - band = 2; - } else if (tuner_frequency < 620000000) { - cp = 3; - band = 4; - } else if (tuner_frequency < 830000000) { - cp = 5; - band = 4; - } else if (tuner_frequency < 895000000) { - cp = 7; - band = 4; - } else - return -EINVAL; - - // assume PLL filter should always be 8MHz for the moment. - filter = 1; - - // calculate divisor - tuner_frequency = (p->frequency + 36125000 + (62500/2)) / 62500; - - // setup tuner buffer - tuner_buf[0] = tuner_frequency >> 8; - tuner_buf[1] = tuner_frequency & 0xff; - tuner_buf[2] = 0xc8; - tuner_buf[3] = (cp << 5) | (filter << 3) | band; - tuner_buf[4] = 0x80; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1) - return -EIO; - - msleep(50); - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer(&budget_ci->budget.i2c_adap, &tuner_msg, 1) != 1) - return -EIO; - - msleep(1); - - return 0; -} - -static u8 dvbc_philips_tdm1316l_inittab[] = { - 0x80, 0x01, - 0x80, 0x00, - 0x81, 0x01, - 0x81, 0x00, - 0x00, 0x09, - 0x01, 0x69, - 0x03, 0x00, - 0x04, 0x00, - 0x07, 0x00, - 0x08, 0x00, - 0x20, 0x00, - 0x21, 0x40, - 0x22, 0x00, - 0x23, 0x00, - 0x24, 0x40, - 0x25, 0x88, - 0x30, 0xff, - 0x31, 0x00, - 0x32, 0xff, - 0x33, 0x00, - 0x34, 0x50, - 0x35, 0x7f, - 0x36, 0x00, - 0x37, 0x20, - 0x38, 0x00, - 0x40, 0x1c, - 0x41, 0xff, - 0x42, 0x29, - 0x43, 0x20, - 0x44, 0xff, - 0x45, 0x00, - 0x46, 0x00, - 0x49, 0x04, - 0x4a, 0x00, - 0x4b, 0x7b, - 0x52, 0x30, - 0x55, 0xae, - 0x56, 0x47, - 0x57, 0xe1, - 0x58, 0x3a, - 0x5a, 0x1e, - 0x5b, 0x34, - 0x60, 0x00, - 0x63, 0x00, - 0x64, 0x00, - 0x65, 0x00, - 0x66, 0x00, - 0x67, 0x00, - 0x68, 0x00, - 0x69, 0x00, - 0x6a, 0x02, - 0x6b, 0x00, - 0x70, 0xff, - 0x71, 0x00, - 0x72, 0x00, - 0x73, 0x00, - 0x74, 0x0c, - 0x80, 0x00, - 0x81, 0x00, - 0x82, 0x00, - 0x83, 0x00, - 0x84, 0x04, - 0x85, 0x80, - 0x86, 0x24, - 0x87, 0x78, - 0x88, 0x10, - 0x89, 0x00, - 0x90, 0x01, - 0x91, 0x01, - 0xa0, 0x04, - 0xa1, 0x00, - 0xa2, 0x00, - 0xb0, 0x91, - 0xb1, 0x0b, - 0xc0, 0x53, - 0xc1, 0x70, - 0xc2, 0x12, - 0xd0, 0x00, - 0xd1, 0x00, - 0xd2, 0x00, - 0xd3, 0x00, - 0xd4, 0x00, - 0xd5, 0x00, - 0xde, 0x00, - 0xdf, 0x00, - 0x61, 0x38, - 0x62, 0x0a, - 0x53, 0x13, - 0x59, 0x08, - 0xff, 0xff, -}; - -static struct stv0297_config dvbc_philips_tdm1316l_config = { - .demod_address = 0x1c, - .inittab = dvbc_philips_tdm1316l_inittab, - .invert = 0, - .stop_during_read = 1, -}; - -static struct tda10023_config tda10023_config = { - .demod_address = 0xc, - .invert = 0, - .xtal = 16000000, - .pll_m = 11, - .pll_p = 3, - .pll_n = 1, - .deltaf = 0xa511, -}; - -static struct tda827x_config tda827x_config = { - .config = 0, -}; - -/* TT S2-3200 DVB-S (STB0899) Inittab */ -static const struct stb0899_s1_reg tt3200_stb0899_s1_init_1[] = { - - { STB0899_DEV_ID , 0x81 }, - { STB0899_DISCNTRL1 , 0x32 }, - { STB0899_DISCNTRL2 , 0x80 }, - { STB0899_DISRX_ST0 , 0x04 }, - { STB0899_DISRX_ST1 , 0x00 }, - { STB0899_DISPARITY , 0x00 }, - { STB0899_DISSTATUS , 0x20 }, - { STB0899_DISF22 , 0x8c }, - { STB0899_DISF22RX , 0x9a }, - { STB0899_SYSREG , 0x0b }, - { STB0899_ACRPRESC , 0x11 }, - { STB0899_ACRDIV1 , 0x0a }, - { STB0899_ACRDIV2 , 0x05 }, - { STB0899_DACR1 , 0x00 }, - { STB0899_DACR2 , 0x00 }, - { STB0899_OUTCFG , 0x00 }, - { STB0899_MODECFG , 0x00 }, - { STB0899_IRQSTATUS_3 , 0x30 }, - { STB0899_IRQSTATUS_2 , 0x00 }, - { STB0899_IRQSTATUS_1 , 0x00 }, - { STB0899_IRQSTATUS_0 , 0x00 }, - { STB0899_IRQMSK_3 , 0xf3 }, - { STB0899_IRQMSK_2 , 0xfc }, - { STB0899_IRQMSK_1 , 0xff }, - { STB0899_IRQMSK_0 , 0xff }, - { STB0899_IRQCFG , 0x00 }, - { STB0899_I2CCFG , 0x88 }, - { STB0899_I2CRPT , 0x48 }, /* 12k Pullup, Repeater=16, Stop=disabled */ - { STB0899_IOPVALUE5 , 0x00 }, - { STB0899_IOPVALUE4 , 0x20 }, - { STB0899_IOPVALUE3 , 0xc9 }, - { STB0899_IOPVALUE2 , 0x90 }, - { STB0899_IOPVALUE1 , 0x40 }, - { STB0899_IOPVALUE0 , 0x00 }, - { STB0899_GPIO00CFG , 0x82 }, - { STB0899_GPIO01CFG , 0x82 }, - { STB0899_GPIO02CFG , 0x82 }, - { STB0899_GPIO03CFG , 0x82 }, - { STB0899_GPIO04CFG , 0x82 }, - { STB0899_GPIO05CFG , 0x82 }, - { STB0899_GPIO06CFG , 0x82 }, - { STB0899_GPIO07CFG , 0x82 }, - { STB0899_GPIO08CFG , 0x82 }, - { STB0899_GPIO09CFG , 0x82 }, - { STB0899_GPIO10CFG , 0x82 }, - { STB0899_GPIO11CFG , 0x82 }, - { STB0899_GPIO12CFG , 0x82 }, - { STB0899_GPIO13CFG , 0x82 }, - { STB0899_GPIO14CFG , 0x82 }, - { STB0899_GPIO15CFG , 0x82 }, - { STB0899_GPIO16CFG , 0x82 }, - { STB0899_GPIO17CFG , 0x82 }, - { STB0899_GPIO18CFG , 0x82 }, - { STB0899_GPIO19CFG , 0x82 }, - { STB0899_GPIO20CFG , 0x82 }, - { STB0899_SDATCFG , 0xb8 }, - { STB0899_SCLTCFG , 0xba }, - { STB0899_AGCRFCFG , 0x1c }, /* 0x11 */ - { STB0899_GPIO22 , 0x82 }, /* AGCBB2CFG */ - { STB0899_GPIO21 , 0x91 }, /* AGCBB1CFG */ - { STB0899_DIRCLKCFG , 0x82 }, - { STB0899_CLKOUT27CFG , 0x7e }, - { STB0899_STDBYCFG , 0x82 }, - { STB0899_CS0CFG , 0x82 }, - { STB0899_CS1CFG , 0x82 }, - { STB0899_DISEQCOCFG , 0x20 }, - { STB0899_GPIO32CFG , 0x82 }, - { STB0899_GPIO33CFG , 0x82 }, - { STB0899_GPIO34CFG , 0x82 }, - { STB0899_GPIO35CFG , 0x82 }, - { STB0899_GPIO36CFG , 0x82 }, - { STB0899_GPIO37CFG , 0x82 }, - { STB0899_GPIO38CFG , 0x82 }, - { STB0899_GPIO39CFG , 0x82 }, - { STB0899_NCOARSE , 0x15 }, /* 0x15 = 27 Mhz Clock, F/3 = 198MHz, F/6 = 99MHz */ - { STB0899_SYNTCTRL , 0x02 }, /* 0x00 = CLK from CLKI, 0x02 = CLK from XTALI */ - { STB0899_FILTCTRL , 0x00 }, - { STB0899_SYSCTRL , 0x00 }, - { STB0899_STOPCLK1 , 0x20 }, - { STB0899_STOPCLK2 , 0x00 }, - { STB0899_INTBUFSTATUS , 0x00 }, - { STB0899_INTBUFCTRL , 0x0a }, - { 0xffff , 0xff }, -}; - -static const struct stb0899_s1_reg tt3200_stb0899_s1_init_3[] = { - { STB0899_DEMOD , 0x00 }, - { STB0899_RCOMPC , 0xc9 }, - { STB0899_AGC1CN , 0x41 }, - { STB0899_AGC1REF , 0x10 }, - { STB0899_RTC , 0x7a }, - { STB0899_TMGCFG , 0x4e }, - { STB0899_AGC2REF , 0x34 }, - { STB0899_TLSR , 0x84 }, - { STB0899_CFD , 0xc7 }, - { STB0899_ACLC , 0x87 }, - { STB0899_BCLC , 0x94 }, - { STB0899_EQON , 0x41 }, - { STB0899_LDT , 0xdd }, - { STB0899_LDT2 , 0xc9 }, - { STB0899_EQUALREF , 0xb4 }, - { STB0899_TMGRAMP , 0x10 }, - { STB0899_TMGTHD , 0x30 }, - { STB0899_IDCCOMP , 0xfb }, - { STB0899_QDCCOMP , 0x03 }, - { STB0899_POWERI , 0x3b }, - { STB0899_POWERQ , 0x3d }, - { STB0899_RCOMP , 0x81 }, - { STB0899_AGCIQIN , 0x80 }, - { STB0899_AGC2I1 , 0x04 }, - { STB0899_AGC2I2 , 0xf5 }, - { STB0899_TLIR , 0x25 }, - { STB0899_RTF , 0x80 }, - { STB0899_DSTATUS , 0x00 }, - { STB0899_LDI , 0xca }, - { STB0899_CFRM , 0xf1 }, - { STB0899_CFRL , 0xf3 }, - { STB0899_NIRM , 0x2a }, - { STB0899_NIRL , 0x05 }, - { STB0899_ISYMB , 0x17 }, - { STB0899_QSYMB , 0xfa }, - { STB0899_SFRH , 0x2f }, - { STB0899_SFRM , 0x68 }, - { STB0899_SFRL , 0x40 }, - { STB0899_SFRUPH , 0x2f }, - { STB0899_SFRUPM , 0x68 }, - { STB0899_SFRUPL , 0x40 }, - { STB0899_EQUAI1 , 0xfd }, - { STB0899_EQUAQ1 , 0x04 }, - { STB0899_EQUAI2 , 0x0f }, - { STB0899_EQUAQ2 , 0xff }, - { STB0899_EQUAI3 , 0xdf }, - { STB0899_EQUAQ3 , 0xfa }, - { STB0899_EQUAI4 , 0x37 }, - { STB0899_EQUAQ4 , 0x0d }, - { STB0899_EQUAI5 , 0xbd }, - { STB0899_EQUAQ5 , 0xf7 }, - { STB0899_DSTATUS2 , 0x00 }, - { STB0899_VSTATUS , 0x00 }, - { STB0899_VERROR , 0xff }, - { STB0899_IQSWAP , 0x2a }, - { STB0899_ECNT1M , 0x00 }, - { STB0899_ECNT1L , 0x00 }, - { STB0899_ECNT2M , 0x00 }, - { STB0899_ECNT2L , 0x00 }, - { STB0899_ECNT3M , 0x00 }, - { STB0899_ECNT3L , 0x00 }, - { STB0899_FECAUTO1 , 0x06 }, - { STB0899_FECM , 0x01 }, - { STB0899_VTH12 , 0xf0 }, - { STB0899_VTH23 , 0xa0 }, - { STB0899_VTH34 , 0x78 }, - { STB0899_VTH56 , 0x4e }, - { STB0899_VTH67 , 0x48 }, - { STB0899_VTH78 , 0x38 }, - { STB0899_PRVIT , 0xff }, - { STB0899_VITSYNC , 0x19 }, - { STB0899_RSULC , 0xb1 }, /* DVB = 0xb1, DSS = 0xa1 */ - { STB0899_TSULC , 0x42 }, - { STB0899_RSLLC , 0x40 }, - { STB0899_TSLPL , 0x12 }, - { STB0899_TSCFGH , 0x0c }, - { STB0899_TSCFGM , 0x00 }, - { STB0899_TSCFGL , 0x0c }, - { STB0899_TSOUT , 0x4d }, /* 0x0d for CAM */ - { STB0899_RSSYNCDEL , 0x00 }, - { STB0899_TSINHDELH , 0x02 }, - { STB0899_TSINHDELM , 0x00 }, - { STB0899_TSINHDELL , 0x00 }, - { STB0899_TSLLSTKM , 0x00 }, - { STB0899_TSLLSTKL , 0x00 }, - { STB0899_TSULSTKM , 0x00 }, - { STB0899_TSULSTKL , 0xab }, - { STB0899_PCKLENUL , 0x00 }, - { STB0899_PCKLENLL , 0xcc }, - { STB0899_RSPCKLEN , 0xcc }, - { STB0899_TSSTATUS , 0x80 }, - { STB0899_ERRCTRL1 , 0xb6 }, - { STB0899_ERRCTRL2 , 0x96 }, - { STB0899_ERRCTRL3 , 0x89 }, - { STB0899_DMONMSK1 , 0x27 }, - { STB0899_DMONMSK0 , 0x03 }, - { STB0899_DEMAPVIT , 0x5c }, - { STB0899_PLPARM , 0x1f }, - { STB0899_PDELCTRL , 0x48 }, - { STB0899_PDELCTRL2 , 0x00 }, - { STB0899_BBHCTRL1 , 0x00 }, - { STB0899_BBHCTRL2 , 0x00 }, - { STB0899_HYSTTHRESH , 0x77 }, - { STB0899_MATCSTM , 0x00 }, - { STB0899_MATCSTL , 0x00 }, - { STB0899_UPLCSTM , 0x00 }, - { STB0899_UPLCSTL , 0x00 }, - { STB0899_DFLCSTM , 0x00 }, - { STB0899_DFLCSTL , 0x00 }, - { STB0899_SYNCCST , 0x00 }, - { STB0899_SYNCDCSTM , 0x00 }, - { STB0899_SYNCDCSTL , 0x00 }, - { STB0899_ISI_ENTRY , 0x00 }, - { STB0899_ISI_BIT_EN , 0x00 }, - { STB0899_MATSTRM , 0x00 }, - { STB0899_MATSTRL , 0x00 }, - { STB0899_UPLSTRM , 0x00 }, - { STB0899_UPLSTRL , 0x00 }, - { STB0899_DFLSTRM , 0x00 }, - { STB0899_DFLSTRL , 0x00 }, - { STB0899_SYNCSTR , 0x00 }, - { STB0899_SYNCDSTRM , 0x00 }, - { STB0899_SYNCDSTRL , 0x00 }, - { STB0899_CFGPDELSTATUS1 , 0x10 }, - { STB0899_CFGPDELSTATUS2 , 0x00 }, - { STB0899_BBFERRORM , 0x00 }, - { STB0899_BBFERRORL , 0x00 }, - { STB0899_UPKTERRORM , 0x00 }, - { STB0899_UPKTERRORL , 0x00 }, - { 0xffff , 0xff }, -}; - -static struct stb0899_config tt3200_config = { - .init_dev = tt3200_stb0899_s1_init_1, - .init_s2_demod = stb0899_s2_init_2, - .init_s1_demod = tt3200_stb0899_s1_init_3, - .init_s2_fec = stb0899_s2_init_4, - .init_tst = stb0899_s1_init_5, - - .postproc = NULL, - - .demod_address = 0x68, - - .xtal_freq = 27000000, - .inversion = IQ_SWAP_ON, - - .lo_clk = 76500000, - .hi_clk = 99000000, - - .esno_ave = STB0899_DVBS2_ESNO_AVE, - .esno_quant = STB0899_DVBS2_ESNO_QUANT, - .avframes_coarse = STB0899_DVBS2_AVFRAMES_COARSE, - .avframes_fine = STB0899_DVBS2_AVFRAMES_FINE, - .miss_threshold = STB0899_DVBS2_MISS_THRESHOLD, - .uwp_threshold_acq = STB0899_DVBS2_UWP_THRESHOLD_ACQ, - .uwp_threshold_track = STB0899_DVBS2_UWP_THRESHOLD_TRACK, - .uwp_threshold_sof = STB0899_DVBS2_UWP_THRESHOLD_SOF, - .sof_search_timeout = STB0899_DVBS2_SOF_SEARCH_TIMEOUT, - - .btr_nco_bits = STB0899_DVBS2_BTR_NCO_BITS, - .btr_gain_shift_offset = STB0899_DVBS2_BTR_GAIN_SHIFT_OFFSET, - .crl_nco_bits = STB0899_DVBS2_CRL_NCO_BITS, - .ldpc_max_iter = STB0899_DVBS2_LDPC_MAX_ITER, - - .tuner_get_frequency = stb6100_get_frequency, - .tuner_set_frequency = stb6100_set_frequency, - .tuner_set_bandwidth = stb6100_set_bandwidth, - .tuner_get_bandwidth = stb6100_get_bandwidth, - .tuner_set_rfsiggain = NULL -}; - -static struct stb6100_config tt3200_stb6100_config = { - .tuner_address = 0x60, - .refclock = 27000000, -}; - -static void frontend_init(struct budget_ci *budget_ci) -{ - switch (budget_ci->budget.dev->pci->subsystem_device) { - case 0x100c: // Hauppauge/TT Nova-CI budget (stv0299/ALPS BSRU6(tsa5059)) - budget_ci->budget.dvb_frontend = - dvb_attach(stv0299_attach, &alps_bsru6_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = alps_bsru6_tuner_set_params; - budget_ci->budget.dvb_frontend->tuner_priv = &budget_ci->budget.i2c_adap; - break; - } - break; - - case 0x100f: // Hauppauge/TT Nova-CI budget (stv0299b/Philips su1278(tsa5059)) - budget_ci->budget.dvb_frontend = - dvb_attach(stv0299_attach, &philips_su1278_tt_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = philips_su1278_tt_tuner_set_params; - break; - } - break; - - case 0x1010: // TT DVB-C CI budget (stv0297/Philips tdm1316l(tda6651tt)) - budget_ci->tuner_pll_address = 0x61; - budget_ci->budget.dvb_frontend = - dvb_attach(stv0297_attach, &dvbc_philips_tdm1316l_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = dvbc_philips_tdm1316l_tuner_set_params; - break; - } - break; - - case 0x1011: // Hauppauge/TT Nova-T budget (tda10045/Philips tdm1316l(tda6651tt) + TDA9889) - budget_ci->tuner_pll_address = 0x63; - budget_ci->budget.dvb_frontend = - dvb_attach(tda10045_attach, &philips_tdm1316l_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - budget_ci->budget.dvb_frontend->ops.tuner_ops.init = philips_tdm1316l_tuner_init; - budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = philips_tdm1316l_tuner_set_params; - break; - } - break; - - case 0x1012: // TT DVB-T CI budget (tda10046/Philips tdm1316l(tda6651tt)) - budget_ci->tuner_pll_address = 0x60; - budget_ci->budget.dvb_frontend = - dvb_attach(tda10046_attach, &philips_tdm1316l_config_invert, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - budget_ci->budget.dvb_frontend->ops.tuner_ops.init = philips_tdm1316l_tuner_init; - budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = philips_tdm1316l_tuner_set_params; - break; - } - break; - - case 0x1017: // TT S-1500 PCI - budget_ci->budget.dvb_frontend = dvb_attach(stv0299_attach, &alps_bsbe1_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - budget_ci->budget.dvb_frontend->ops.tuner_ops.set_params = alps_bsbe1_tuner_set_params; - budget_ci->budget.dvb_frontend->tuner_priv = &budget_ci->budget.i2c_adap; - - budget_ci->budget.dvb_frontend->ops.dishnetwork_send_legacy_command = NULL; - if (dvb_attach(lnbp21_attach, budget_ci->budget.dvb_frontend, &budget_ci->budget.i2c_adap, LNBP21_LLC, 0) == NULL) { - printk("%s: No LNBP21 found!\n", __func__); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } - break; - - case 0x101a: /* TT Budget-C-1501 (philips tda10023/philips tda8274A) */ - budget_ci->budget.dvb_frontend = dvb_attach(tda10023_attach, &tda10023_config, &budget_ci->budget.i2c_adap, 0x48); - if (budget_ci->budget.dvb_frontend) { - if (dvb_attach(tda827x_attach, budget_ci->budget.dvb_frontend, 0x61, &budget_ci->budget.i2c_adap, &tda827x_config) == NULL) { - printk(KERN_ERR "%s: No tda827x found!\n", __func__); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } - break; - - case 0x101b: /* TT S-1500B (BSBE1-D01A - STV0288/STB6000/LNBP21) */ - budget_ci->budget.dvb_frontend = dvb_attach(stv0288_attach, &stv0288_bsbe1_d01a_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - if (dvb_attach(stb6000_attach, budget_ci->budget.dvb_frontend, 0x63, &budget_ci->budget.i2c_adap)) { - if (!dvb_attach(lnbp21_attach, budget_ci->budget.dvb_frontend, &budget_ci->budget.i2c_adap, 0, 0)) { - printk(KERN_ERR "%s: No LNBP21 found!\n", __func__); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } else { - printk(KERN_ERR "%s: No STB6000 found!\n", __func__); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } - break; - - case 0x1019: // TT S2-3200 PCI - /* - * NOTE! on some STB0899 versions, the internal PLL takes a longer time - * to settle, aka LOCK. On the older revisions of the chip, we don't see - * this, as a result on the newer chips the entire clock tree, will not - * be stable after a freshly POWER 'ed up situation. - * In this case, we should RESET the STB0899 (Active LOW) and wait for - * PLL stabilization. - * - * On the TT S2 3200 and clones, the STB0899 demodulator's RESETB is - * connected to the SAA7146 GPIO, GPIO2, Pin 142 - */ - /* Reset Demodulator */ - saa7146_setgpio(budget_ci->budget.dev, 2, SAA7146_GPIO_OUTLO); - /* Wait for everything to die */ - msleep(50); - /* Pull it up out of Reset state */ - saa7146_setgpio(budget_ci->budget.dev, 2, SAA7146_GPIO_OUTHI); - /* Wait for PLL to stabilize */ - msleep(250); - /* - * PLL state should be stable now. Ideally, we should check - * for PLL LOCK status. But well, never mind! - */ - budget_ci->budget.dvb_frontend = dvb_attach(stb0899_attach, &tt3200_config, &budget_ci->budget.i2c_adap); - if (budget_ci->budget.dvb_frontend) { - if (dvb_attach(stb6100_attach, budget_ci->budget.dvb_frontend, &tt3200_stb6100_config, &budget_ci->budget.i2c_adap)) { - if (!dvb_attach(lnbp21_attach, budget_ci->budget.dvb_frontend, &budget_ci->budget.i2c_adap, 0, 0)) { - printk("%s: No LNBP21 found!\n", __func__); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } else { - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } - break; - - } - - if (budget_ci->budget.dvb_frontend == NULL) { - printk("budget-ci: A frontend driver was not found for device [%04x:%04x] subsystem [%04x:%04x]\n", - budget_ci->budget.dev->pci->vendor, - budget_ci->budget.dev->pci->device, - budget_ci->budget.dev->pci->subsystem_vendor, - budget_ci->budget.dev->pci->subsystem_device); - } else { - if (dvb_register_frontend - (&budget_ci->budget.dvb_adapter, budget_ci->budget.dvb_frontend)) { - printk("budget-ci: Frontend registration failed!\n"); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - budget_ci->budget.dvb_frontend = NULL; - } - } -} - -static int budget_ci_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info) -{ - struct budget_ci *budget_ci; - int err; - - budget_ci = kzalloc(sizeof(struct budget_ci), GFP_KERNEL); - if (!budget_ci) { - err = -ENOMEM; - goto out1; - } - - dprintk(2, "budget_ci: %p\n", budget_ci); - - dev->ext_priv = budget_ci; - - err = ttpci_budget_init(&budget_ci->budget, dev, info, THIS_MODULE, - adapter_nr); - if (err) - goto out2; - - err = msp430_ir_init(budget_ci); - if (err) - goto out3; - - ciintf_init(budget_ci); - - budget_ci->budget.dvb_adapter.priv = budget_ci; - frontend_init(budget_ci); - - ttpci_budget_init_hooks(&budget_ci->budget); - - return 0; - -out3: - ttpci_budget_deinit(&budget_ci->budget); -out2: - kfree(budget_ci); -out1: - return err; -} - -static int budget_ci_detach(struct saa7146_dev *dev) -{ - struct budget_ci *budget_ci = (struct budget_ci *) dev->ext_priv; - struct saa7146_dev *saa = budget_ci->budget.dev; - int err; - - if (budget_ci->budget.ci_present) - ciintf_deinit(budget_ci); - msp430_ir_deinit(budget_ci); - if (budget_ci->budget.dvb_frontend) { - dvb_unregister_frontend(budget_ci->budget.dvb_frontend); - dvb_frontend_detach(budget_ci->budget.dvb_frontend); - } - err = ttpci_budget_deinit(&budget_ci->budget); - - // disable frontend and CI interface - saa7146_setgpio(saa, 2, SAA7146_GPIO_INPUT); - - kfree(budget_ci); - - return err; -} - -static struct saa7146_extension budget_extension; - -MAKE_BUDGET_INFO(ttbs2, "TT-Budget/S-1500 PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttbci, "TT-Budget/WinTV-NOVA-CI PCI", BUDGET_TT_HW_DISEQC); -MAKE_BUDGET_INFO(ttbt2, "TT-Budget/WinTV-NOVA-T PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttbtci, "TT-Budget-T-CI PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttbcci, "TT-Budget-C-CI PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttc1501, "TT-Budget C-1501 PCI", BUDGET_TT); -MAKE_BUDGET_INFO(tt3200, "TT-Budget S2-3200 PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttbs1500b, "TT-Budget S-1500B PCI", BUDGET_TT); - -static const struct pci_device_id pci_tbl[] = { - MAKE_EXTENSION_PCI(ttbci, 0x13c2, 0x100c), - MAKE_EXTENSION_PCI(ttbci, 0x13c2, 0x100f), - MAKE_EXTENSION_PCI(ttbcci, 0x13c2, 0x1010), - MAKE_EXTENSION_PCI(ttbt2, 0x13c2, 0x1011), - MAKE_EXTENSION_PCI(ttbtci, 0x13c2, 0x1012), - MAKE_EXTENSION_PCI(ttbs2, 0x13c2, 0x1017), - MAKE_EXTENSION_PCI(ttc1501, 0x13c2, 0x101a), - MAKE_EXTENSION_PCI(tt3200, 0x13c2, 0x1019), - MAKE_EXTENSION_PCI(ttbs1500b, 0x13c2, 0x101b), - { - .vendor = 0, - } -}; - -MODULE_DEVICE_TABLE(pci, pci_tbl); - -static struct saa7146_extension budget_extension = { - .name = "budget_ci dvb", - .flags = SAA7146_USE_I2C_IRQ, - - .module = THIS_MODULE, - .pci_tbl = &pci_tbl[0], - .attach = budget_ci_attach, - .detach = budget_ci_detach, - - .irq_mask = MASK_03 | MASK_06 | MASK_10, - .irq_func = budget_ci_irq, -}; - -static int __init budget_ci_init(void) -{ - return saa7146_register_extension(&budget_extension); -} - -static void __exit budget_ci_exit(void) -{ - saa7146_unregister_extension(&budget_extension); -} - -module_init(budget_ci_init); -module_exit(budget_ci_exit); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Michael Hunold, Jack Thomasson, Andrew de Quincey, others"); -MODULE_DESCRIPTION("driver for the SAA7146 based so-called budget PCI DVB cards w/ CI-module produced by Siemens, Technotrend, Hauppauge"); diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/budget-core.c b/drivers/staging/media/deprecated/saa7146/ttpci/budget-core.c deleted file mode 100644 index 5d5796f24469..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/budget-core.c +++ /dev/null @@ -1,603 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * budget-core.c: driver for the SAA7146 based Budget DVB cards - * - * Compiled from various sources by Michael Hunold <michael@xxxxxxx> - * - * Copyright (C) 2002 Ralph Metzler <rjkm@xxxxxxxxxxxxxx> - * - * Copyright (C) 1999-2002 Ralph Metzler - * & Marcus Metzler for convergence integrated media GmbH - * - * 26feb2004 Support for FS Activy Card (Grundig tuner) by - * Michael Dreher <michael@xxxxxxxx>, - * Oliver Endriss <o.endriss@xxxxxx>, - * Andreas 'randy' Weinberger - * - * the project's page is at https://linuxtv.org - */ - - -#include "budget.h" -#include "ttpci-eeprom.h" - -#define TS_WIDTH (2 * TS_SIZE) -#define TS_WIDTH_ACTIVY TS_SIZE -#define TS_WIDTH_DVBC TS_SIZE -#define TS_HEIGHT_MASK 0xf00 -#define TS_HEIGHT_MASK_ACTIVY 0xc00 -#define TS_HEIGHT_MASK_DVBC 0xe00 -#define TS_MIN_BUFSIZE_K 188 -#define TS_MAX_BUFSIZE_K 1410 -#define TS_MAX_BUFSIZE_K_ACTIVY 564 -#define TS_MAX_BUFSIZE_K_DVBC 1316 -#define BUFFER_WARNING_WAIT (30*HZ) - -int budget_debug; -static int dma_buffer_size = TS_MIN_BUFSIZE_K; -module_param_named(debug, budget_debug, int, 0644); -module_param_named(bufsize, dma_buffer_size, int, 0444); -MODULE_PARM_DESC(debug, "Turn on/off budget debugging (default:off)."); -MODULE_PARM_DESC(bufsize, "DMA buffer size in KB, default: 188, min: 188, max: 1410 (Activy: 564)"); - -/**************************************************************************** - * TT budget / WinTV Nova - ****************************************************************************/ - -static int stop_ts_capture(struct budget *budget) -{ - dprintk(2, "budget: %p\n", budget); - - saa7146_write(budget->dev, MC1, MASK_20); // DMA3 off - SAA7146_IER_DISABLE(budget->dev, MASK_10); - return 0; -} - -static int start_ts_capture(struct budget *budget) -{ - struct saa7146_dev *dev = budget->dev; - - dprintk(2, "budget: %p\n", budget); - - if (!budget->feeding || !budget->fe_synced) - return 0; - - saa7146_write(dev, MC1, MASK_20); // DMA3 off - - memset(budget->grabbing, 0x00, budget->buffer_size); - - saa7146_write(dev, PCI_BT_V1, 0x001c0000 | (saa7146_read(dev, PCI_BT_V1) & ~0x001f0000)); - - budget->ttbp = 0; - - /* - * Signal path on the Activy: - * - * tuner -> SAA7146 port A -> SAA7146 BRS -> SAA7146 DMA3 -> memory - * - * Since the tuner feeds 204 bytes packets into the SAA7146, - * DMA3 is configured to strip the trailing 16 FEC bytes: - * Pitch: 188, NumBytes3: 188, NumLines3: 1024 - */ - - switch(budget->card->type) { - case BUDGET_FS_ACTIVY: - saa7146_write(dev, DD1_INIT, 0x04000000); - saa7146_write(dev, MC2, (MASK_09 | MASK_25)); - saa7146_write(dev, BRS_CTRL, 0x00000000); - break; - case BUDGET_PATCH: - saa7146_write(dev, DD1_INIT, 0x00000200); - saa7146_write(dev, MC2, (MASK_10 | MASK_26)); - saa7146_write(dev, BRS_CTRL, 0x60000000); - break; - case BUDGET_CIN1200C_MK3: - case BUDGET_KNC1C_MK3: - case BUDGET_KNC1C_TDA10024: - case BUDGET_KNC1CP_MK3: - if (budget->video_port == BUDGET_VIDEO_PORTA) { - saa7146_write(dev, DD1_INIT, 0x06000200); - saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26)); - saa7146_write(dev, BRS_CTRL, 0x00000000); - } else { - saa7146_write(dev, DD1_INIT, 0x00000600); - saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26)); - saa7146_write(dev, BRS_CTRL, 0x60000000); - } - break; - default: - if (budget->video_port == BUDGET_VIDEO_PORTA) { - saa7146_write(dev, DD1_INIT, 0x06000200); - saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26)); - saa7146_write(dev, BRS_CTRL, 0x00000000); - } else { - saa7146_write(dev, DD1_INIT, 0x02000600); - saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26)); - saa7146_write(dev, BRS_CTRL, 0x60000000); - } - } - - saa7146_write(dev, MC2, (MASK_08 | MASK_24)); - mdelay(10); - - saa7146_write(dev, BASE_ODD3, 0); - if (budget->buffer_size > budget->buffer_height * budget->buffer_width) { - // using odd/even buffers - saa7146_write(dev, BASE_EVEN3, budget->buffer_height * budget->buffer_width); - } else { - // using a single buffer - saa7146_write(dev, BASE_EVEN3, 0); - } - saa7146_write(dev, PROT_ADDR3, budget->buffer_size); - saa7146_write(dev, BASE_PAGE3, budget->pt.dma | ME1 | 0x90); - - saa7146_write(dev, PITCH3, budget->buffer_width); - saa7146_write(dev, NUM_LINE_BYTE3, - (budget->buffer_height << 16) | budget->buffer_width); - - saa7146_write(dev, MC2, (MASK_04 | MASK_20)); - - SAA7146_ISR_CLEAR(budget->dev, MASK_10); /* VPE */ - SAA7146_IER_ENABLE(budget->dev, MASK_10); /* VPE */ - saa7146_write(dev, MC1, (MASK_04 | MASK_20)); /* DMA3 on */ - - return 0; -} - -static int budget_read_fe_status(struct dvb_frontend *fe, - enum fe_status *status) -{ - struct budget *budget = (struct budget *) fe->dvb->priv; - int synced; - int ret; - - if (budget->read_fe_status) - ret = budget->read_fe_status(fe, status); - else - ret = -EINVAL; - - if (!ret) { - synced = (*status & FE_HAS_LOCK); - if (synced != budget->fe_synced) { - budget->fe_synced = synced; - spin_lock(&budget->feedlock); - if (synced) - start_ts_capture(budget); - else - stop_ts_capture(budget); - spin_unlock(&budget->feedlock); - } - } - return ret; -} - -static void vpeirq(struct tasklet_struct *t) -{ - struct budget *budget = from_tasklet(budget, t, vpe_tasklet); - u8 *mem = (u8 *) (budget->grabbing); - u32 olddma = budget->ttbp; - u32 newdma = saa7146_read(budget->dev, PCI_VDP3); - u32 count; - - /* Ensure streamed PCI data is synced to CPU */ - dma_sync_sg_for_cpu(&budget->dev->pci->dev, budget->pt.slist, - budget->pt.nents, DMA_FROM_DEVICE); - - /* nearest lower position divisible by 188 */ - newdma -= newdma % 188; - - if (newdma >= budget->buffer_size) - return; - - budget->ttbp = newdma; - - if (budget->feeding == 0 || newdma == olddma) - return; - - if (newdma > olddma) { /* no wraparound, dump olddma..newdma */ - count = newdma - olddma; - dvb_dmx_swfilter_packets(&budget->demux, mem + olddma, count / 188); - } else { /* wraparound, dump olddma..buflen and 0..newdma */ - count = budget->buffer_size - olddma; - dvb_dmx_swfilter_packets(&budget->demux, mem + olddma, count / 188); - count += newdma; - dvb_dmx_swfilter_packets(&budget->demux, mem, newdma / 188); - } - - if (count > budget->buffer_warning_threshold) - budget->buffer_warnings++; - - if (budget->buffer_warnings && time_after(jiffies, budget->buffer_warning_time)) { - printk("%s %s: used %d times >80%% of buffer (%u bytes now)\n", - budget->dev->name, __func__, budget->buffer_warnings, count); - budget->buffer_warning_time = jiffies + BUFFER_WARNING_WAIT; - budget->buffer_warnings = 0; - } -} - - -static int ttpci_budget_debiread_nolock(struct budget *budget, u32 config, - int addr, int count, int nobusyloop) -{ - struct saa7146_dev *saa = budget->dev; - int result; - - result = saa7146_wait_for_debi_done(saa, nobusyloop); - if (result < 0) - return result; - - saa7146_write(saa, DEBI_COMMAND, (count << 17) | 0x10000 | (addr & 0xffff)); - saa7146_write(saa, DEBI_CONFIG, config); - saa7146_write(saa, DEBI_PAGE, 0); - saa7146_write(saa, MC2, (2 << 16) | 2); - - result = saa7146_wait_for_debi_done(saa, nobusyloop); - if (result < 0) - return result; - - result = saa7146_read(saa, DEBI_AD); - result &= (0xffffffffUL >> ((4 - count) * 8)); - return result; -} - -int ttpci_budget_debiread(struct budget *budget, u32 config, int addr, int count, - int uselocks, int nobusyloop) -{ - if (count > 4 || count <= 0) - return 0; - - if (uselocks) { - unsigned long flags; - int result; - - spin_lock_irqsave(&budget->debilock, flags); - result = ttpci_budget_debiread_nolock(budget, config, addr, - count, nobusyloop); - spin_unlock_irqrestore(&budget->debilock, flags); - return result; - } - return ttpci_budget_debiread_nolock(budget, config, addr, - count, nobusyloop); -} - -static int ttpci_budget_debiwrite_nolock(struct budget *budget, u32 config, - int addr, int count, u32 value, int nobusyloop) -{ - struct saa7146_dev *saa = budget->dev; - int result; - - result = saa7146_wait_for_debi_done(saa, nobusyloop); - if (result < 0) - return result; - - saa7146_write(saa, DEBI_COMMAND, (count << 17) | 0x00000 | (addr & 0xffff)); - saa7146_write(saa, DEBI_CONFIG, config); - saa7146_write(saa, DEBI_PAGE, 0); - saa7146_write(saa, DEBI_AD, value); - saa7146_write(saa, MC2, (2 << 16) | 2); - - result = saa7146_wait_for_debi_done(saa, nobusyloop); - return result < 0 ? result : 0; -} - -int ttpci_budget_debiwrite(struct budget *budget, u32 config, int addr, - int count, u32 value, int uselocks, int nobusyloop) -{ - if (count > 4 || count <= 0) - return 0; - - if (uselocks) { - unsigned long flags; - int result; - - spin_lock_irqsave(&budget->debilock, flags); - result = ttpci_budget_debiwrite_nolock(budget, config, addr, - count, value, nobusyloop); - spin_unlock_irqrestore(&budget->debilock, flags); - return result; - } - return ttpci_budget_debiwrite_nolock(budget, config, addr, - count, value, nobusyloop); -} - - -/**************************************************************************** - * DVB API SECTION - ****************************************************************************/ - -static int budget_start_feed(struct dvb_demux_feed *feed) -{ - struct dvb_demux *demux = feed->demux; - struct budget *budget = (struct budget *) demux->priv; - int status = 0; - - dprintk(2, "budget: %p\n", budget); - - if (!demux->dmx.frontend) - return -EINVAL; - - spin_lock(&budget->feedlock); - feed->pusi_seen = false; /* have a clean section start */ - if (budget->feeding++ == 0) - status = start_ts_capture(budget); - spin_unlock(&budget->feedlock); - return status; -} - -static int budget_stop_feed(struct dvb_demux_feed *feed) -{ - struct dvb_demux *demux = feed->demux; - struct budget *budget = (struct budget *) demux->priv; - int status = 0; - - dprintk(2, "budget: %p\n", budget); - - spin_lock(&budget->feedlock); - if (--budget->feeding == 0) - status = stop_ts_capture(budget); - spin_unlock(&budget->feedlock); - return status; -} - -static int budget_register(struct budget *budget) -{ - struct dvb_demux *dvbdemux = &budget->demux; - int ret; - - dprintk(2, "budget: %p\n", budget); - - dvbdemux->priv = (void *) budget; - - dvbdemux->filternum = 256; - dvbdemux->feednum = 256; - dvbdemux->start_feed = budget_start_feed; - dvbdemux->stop_feed = budget_stop_feed; - dvbdemux->write_to_decoder = NULL; - - dvbdemux->dmx.capabilities = (DMX_TS_FILTERING | DMX_SECTION_FILTERING | - DMX_MEMORY_BASED_FILTERING); - - dvb_dmx_init(&budget->demux); - - budget->dmxdev.filternum = 256; - budget->dmxdev.demux = &dvbdemux->dmx; - budget->dmxdev.capabilities = 0; - - dvb_dmxdev_init(&budget->dmxdev, &budget->dvb_adapter); - - budget->hw_frontend.source = DMX_FRONTEND_0; - - ret = dvbdemux->dmx.add_frontend(&dvbdemux->dmx, &budget->hw_frontend); - - if (ret < 0) - goto err_release_dmx; - - budget->mem_frontend.source = DMX_MEMORY_FE; - ret = dvbdemux->dmx.add_frontend(&dvbdemux->dmx, &budget->mem_frontend); - if (ret < 0) - goto err_release_dmx; - - ret = dvbdemux->dmx.connect_frontend(&dvbdemux->dmx, &budget->hw_frontend); - if (ret < 0) - goto err_release_dmx; - - dvb_net_init(&budget->dvb_adapter, &budget->dvb_net, &dvbdemux->dmx); - - return 0; - -err_release_dmx: - dvb_dmxdev_release(&budget->dmxdev); - dvb_dmx_release(&budget->demux); - return ret; -} - -static void budget_unregister(struct budget *budget) -{ - struct dvb_demux *dvbdemux = &budget->demux; - - dprintk(2, "budget: %p\n", budget); - - dvb_net_release(&budget->dvb_net); - - dvbdemux->dmx.close(&dvbdemux->dmx); - dvbdemux->dmx.remove_frontend(&dvbdemux->dmx, &budget->hw_frontend); - dvbdemux->dmx.remove_frontend(&dvbdemux->dmx, &budget->mem_frontend); - - dvb_dmxdev_release(&budget->dmxdev); - dvb_dmx_release(&budget->demux); -} - -int ttpci_budget_init(struct budget *budget, struct saa7146_dev *dev, - struct saa7146_pci_extension_data *info, - struct module *owner, short *adapter_nums) -{ - int ret = 0; - struct budget_info *bi = info->ext_priv; - int max_bufsize; - int height_mask; - - memset(budget, 0, sizeof(struct budget)); - - dprintk(2, "dev: %p, budget: %p\n", dev, budget); - - budget->card = bi; - budget->dev = (struct saa7146_dev *) dev; - - switch(budget->card->type) { - case BUDGET_FS_ACTIVY: - budget->buffer_width = TS_WIDTH_ACTIVY; - max_bufsize = TS_MAX_BUFSIZE_K_ACTIVY; - height_mask = TS_HEIGHT_MASK_ACTIVY; - break; - - case BUDGET_KNC1C: - case BUDGET_KNC1CP: - case BUDGET_CIN1200C: - case BUDGET_KNC1C_MK3: - case BUDGET_KNC1C_TDA10024: - case BUDGET_KNC1CP_MK3: - case BUDGET_CIN1200C_MK3: - budget->buffer_width = TS_WIDTH_DVBC; - max_bufsize = TS_MAX_BUFSIZE_K_DVBC; - height_mask = TS_HEIGHT_MASK_DVBC; - break; - - default: - budget->buffer_width = TS_WIDTH; - max_bufsize = TS_MAX_BUFSIZE_K; - height_mask = TS_HEIGHT_MASK; - } - - if (dma_buffer_size < TS_MIN_BUFSIZE_K) - dma_buffer_size = TS_MIN_BUFSIZE_K; - else if (dma_buffer_size > max_bufsize) - dma_buffer_size = max_bufsize; - - budget->buffer_height = dma_buffer_size * 1024 / budget->buffer_width; - if (budget->buffer_height > 0xfff) { - budget->buffer_height /= 2; - budget->buffer_height &= height_mask; - budget->buffer_size = 2 * budget->buffer_height * budget->buffer_width; - } else { - budget->buffer_height &= height_mask; - budget->buffer_size = budget->buffer_height * budget->buffer_width; - } - budget->buffer_warning_threshold = budget->buffer_size * 80/100; - budget->buffer_warnings = 0; - budget->buffer_warning_time = jiffies; - - dprintk(2, "%s: buffer type = %s, width = %d, height = %d\n", - budget->dev->name, - budget->buffer_size > budget->buffer_width * budget->buffer_height ? "odd/even" : "single", - budget->buffer_width, budget->buffer_height); - printk("%s: dma buffer size %u\n", budget->dev->name, budget->buffer_size); - - ret = dvb_register_adapter(&budget->dvb_adapter, budget->card->name, - owner, &budget->dev->pci->dev, adapter_nums); - if (ret < 0) - return ret; - - /* set dd1 stream a & b */ - saa7146_write(dev, DD1_STREAM_B, 0x00000000); - saa7146_write(dev, MC2, (MASK_09 | MASK_25)); - saa7146_write(dev, MC2, (MASK_10 | MASK_26)); - saa7146_write(dev, DD1_INIT, 0x02000000); - saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26)); - - if (bi->type != BUDGET_FS_ACTIVY) - budget->video_port = BUDGET_VIDEO_PORTB; - else - budget->video_port = BUDGET_VIDEO_PORTA; - spin_lock_init(&budget->feedlock); - spin_lock_init(&budget->debilock); - - /* the Siemens DVB needs this if you want to have the i2c chips - get recognized before the main driver is loaded */ - if (bi->type != BUDGET_FS_ACTIVY) - saa7146_write(dev, GPIO_CTRL, 0x500000); /* GPIO 3 = 1 */ - - strscpy(budget->i2c_adap.name, budget->card->name, - sizeof(budget->i2c_adap.name)); - - saa7146_i2c_adapter_prepare(dev, &budget->i2c_adap, SAA7146_I2C_BUS_BIT_RATE_120); - strscpy(budget->i2c_adap.name, budget->card->name, - sizeof(budget->i2c_adap.name)); - - if (i2c_add_adapter(&budget->i2c_adap) < 0) { - ret = -ENOMEM; - goto err_dvb_unregister; - } - - ttpci_eeprom_parse_mac(&budget->i2c_adap, budget->dvb_adapter.proposed_mac); - - budget->grabbing = saa7146_vmalloc_build_pgtable(dev->pci, budget->buffer_size, &budget->pt); - if (NULL == budget->grabbing) { - ret = -ENOMEM; - goto err_del_i2c; - } - - saa7146_write(dev, PCI_BT_V1, 0x001c0000); - /* upload all */ - saa7146_write(dev, GPIO_CTRL, 0x000000); - - tasklet_setup(&budget->vpe_tasklet, vpeirq); - - /* frontend power on */ - if (bi->type != BUDGET_FS_ACTIVY) - saa7146_setgpio(dev, 2, SAA7146_GPIO_OUTHI); - - if ((ret = budget_register(budget)) == 0) - return 0; /* Everything OK */ - - /* An error occurred, cleanup resources */ - saa7146_vfree_destroy_pgtable(dev->pci, budget->grabbing, &budget->pt); - -err_del_i2c: - i2c_del_adapter(&budget->i2c_adap); - -err_dvb_unregister: - dvb_unregister_adapter(&budget->dvb_adapter); - - return ret; -} - -void ttpci_budget_init_hooks(struct budget *budget) -{ - if (budget->dvb_frontend && !budget->read_fe_status) { - budget->read_fe_status = budget->dvb_frontend->ops.read_status; - budget->dvb_frontend->ops.read_status = budget_read_fe_status; - } -} - -int ttpci_budget_deinit(struct budget *budget) -{ - struct saa7146_dev *dev = budget->dev; - - dprintk(2, "budget: %p\n", budget); - - budget_unregister(budget); - - tasklet_kill(&budget->vpe_tasklet); - - saa7146_vfree_destroy_pgtable(dev->pci, budget->grabbing, &budget->pt); - - i2c_del_adapter(&budget->i2c_adap); - - dvb_unregister_adapter(&budget->dvb_adapter); - - return 0; -} - -void ttpci_budget_irq10_handler(struct saa7146_dev *dev, u32 * isr) -{ - struct budget *budget = (struct budget *) dev->ext_priv; - - dprintk(8, "dev: %p, budget: %p\n", dev, budget); - - if (*isr & MASK_10) - tasklet_schedule(&budget->vpe_tasklet); -} - -void ttpci_budget_set_video_port(struct saa7146_dev *dev, int video_port) -{ - struct budget *budget = (struct budget *) dev->ext_priv; - - spin_lock(&budget->feedlock); - budget->video_port = video_port; - if (budget->feeding) { - stop_ts_capture(budget); - start_ts_capture(budget); - } - spin_unlock(&budget->feedlock); -} - -EXPORT_SYMBOL_GPL(ttpci_budget_debiread); -EXPORT_SYMBOL_GPL(ttpci_budget_debiwrite); -EXPORT_SYMBOL_GPL(ttpci_budget_init); -EXPORT_SYMBOL_GPL(ttpci_budget_init_hooks); -EXPORT_SYMBOL_GPL(ttpci_budget_deinit); -EXPORT_SYMBOL_GPL(ttpci_budget_irq10_handler); -EXPORT_SYMBOL_GPL(ttpci_budget_set_video_port); -EXPORT_SYMBOL_GPL(budget_debug); - -MODULE_LICENSE("GPL"); diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/budget.c b/drivers/staging/media/deprecated/saa7146/ttpci/budget.c deleted file mode 100644 index a88711a3ac7f..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/budget.c +++ /dev/null @@ -1,883 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * budget.c: driver for the SAA7146 based Budget DVB cards - * - * Compiled from various sources by Michael Hunold <michael@xxxxxxx> - * - * Copyright (C) 2002 Ralph Metzler <rjkm@xxxxxxxxxxxxxx> - * - * Copyright (C) 1999-2002 Ralph Metzler - * & Marcus Metzler for convergence integrated media GmbH - * - * 26feb2004 Support for FS Activy Card (Grundig tuner) by - * Michael Dreher <michael@xxxxxxxx>, - * Oliver Endriss <o.endriss@xxxxxx> and - * Andreas 'randy' Weinberger - * - * the project's page is at https://linuxtv.org - */ - -#include "budget.h" -#include "stv0299.h" -#include "ves1x93.h" -#include "ves1820.h" -#include "l64781.h" -#include "tda8083.h" -#include "s5h1420.h" -#include "tda10086.h" -#include "tda826x.h" -#include "lnbp21.h" -#include "bsru6.h" -#include "bsbe1.h" -#include "tdhd1.h" -#include "stv6110x.h" -#include "stv090x.h" -#include "isl6423.h" -#include "lnbh24.h" - - -static int diseqc_method; -module_param(diseqc_method, int, 0444); -MODULE_PARM_DESC(diseqc_method, "Select DiSEqC method for subsystem id 13c2:1003, 0: default, 1: more reliable (for newer revisions only)"); - -DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); - -static void Set22K (struct budget *budget, int state) -{ - struct saa7146_dev *dev=budget->dev; - dprintk(2, "budget: %p\n", budget); - saa7146_setgpio(dev, 3, (state ? SAA7146_GPIO_OUTHI : SAA7146_GPIO_OUTLO)); -} - -/* Diseqc functions only for TT Budget card */ -/* taken from the Skyvision DVB driver by - Ralph Metzler <rjkm@xxxxxxxxxxxxxx> */ - -static void DiseqcSendBit (struct budget *budget, int data) -{ - struct saa7146_dev *dev=budget->dev; - dprintk(2, "budget: %p\n", budget); - - saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTHI); - udelay(data ? 500 : 1000); - saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO); - udelay(data ? 1000 : 500); -} - -static void DiseqcSendByte (struct budget *budget, int data) -{ - int i, par=1, d; - - dprintk(2, "budget: %p\n", budget); - - for (i=7; i>=0; i--) { - d = (data>>i)&1; - par ^= d; - DiseqcSendBit(budget, d); - } - - DiseqcSendBit(budget, par); -} - -static int SendDiSEqCMsg (struct budget *budget, int len, u8 *msg, unsigned long burst) -{ - struct saa7146_dev *dev=budget->dev; - int i; - - dprintk(2, "budget: %p\n", budget); - - saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO); - mdelay(16); - - for (i=0; i<len; i++) - DiseqcSendByte(budget, msg[i]); - - mdelay(16); - - if (burst!=-1) { - if (burst) - DiseqcSendByte(budget, 0xff); - else { - saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTHI); - mdelay(12); - udelay(500); - saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO); - } - msleep(20); - } - - return 0; -} - -/* - * Routines for the Fujitsu Siemens Activy budget card - * 22 kHz tone and DiSEqC are handled by the frontend. - * Voltage must be set here. - * GPIO 1: LNBP EN, GPIO 2: LNBP VSEL - */ -static int SetVoltage_Activy(struct budget *budget, - enum fe_sec_voltage voltage) -{ - struct saa7146_dev *dev=budget->dev; - - dprintk(2, "budget: %p\n", budget); - - switch (voltage) { - case SEC_VOLTAGE_13: - saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); - saa7146_setgpio(dev, 2, SAA7146_GPIO_OUTLO); - break; - case SEC_VOLTAGE_18: - saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); - saa7146_setgpio(dev, 2, SAA7146_GPIO_OUTHI); - break; - case SEC_VOLTAGE_OFF: - saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTLO); - break; - default: - return -EINVAL; - } - - return 0; -} - -static int siemens_budget_set_voltage(struct dvb_frontend *fe, - enum fe_sec_voltage voltage) -{ - struct budget* budget = (struct budget*) fe->dvb->priv; - - return SetVoltage_Activy (budget, voltage); -} - -static int budget_set_tone(struct dvb_frontend *fe, - enum fe_sec_tone_mode tone) -{ - struct budget* budget = (struct budget*) fe->dvb->priv; - - switch (tone) { - case SEC_TONE_ON: - Set22K (budget, 1); - break; - - case SEC_TONE_OFF: - Set22K (budget, 0); - break; - - default: - return -EINVAL; - } - - return 0; -} - -static int budget_diseqc_send_master_cmd(struct dvb_frontend* fe, struct dvb_diseqc_master_cmd* cmd) -{ - struct budget* budget = (struct budget*) fe->dvb->priv; - - SendDiSEqCMsg (budget, cmd->msg_len, cmd->msg, 0); - - return 0; -} - -static int budget_diseqc_send_burst(struct dvb_frontend *fe, - enum fe_sec_mini_cmd minicmd) -{ - struct budget* budget = (struct budget*) fe->dvb->priv; - - SendDiSEqCMsg (budget, 0, NULL, minicmd); - - return 0; -} - -static int alps_bsrv2_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget* budget = (struct budget*) fe->dvb->priv; - u8 pwr = 0; - u8 buf[4]; - struct i2c_msg msg = { .addr = 0x61, .flags = 0, .buf = buf, .len = sizeof(buf) }; - u32 div = (c->frequency + 479500) / 125; - - if (c->frequency > 2000000) - pwr = 3; - else if (c->frequency > 1800000) - pwr = 2; - else if (c->frequency > 1600000) - pwr = 1; - else if (c->frequency > 1200000) - pwr = 0; - else if (c->frequency >= 1100000) - pwr = 1; - else pwr = 2; - - buf[0] = (div >> 8) & 0x7f; - buf[1] = div & 0xff; - buf[2] = ((div & 0x18000) >> 10) | 0x95; - buf[3] = (pwr << 6) | 0x30; - - // NOTE: since we're using a prescaler of 2, we set the - // divisor frequency to 62.5kHz and divide by 125 above - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer (&budget->i2c_adap, &msg, 1) != 1) return -EIO; - return 0; -} - -static struct ves1x93_config alps_bsrv2_config = -{ - .demod_address = 0x08, - .xin = 90100000UL, - .invert_pwm = 0, -}; - -static int alps_tdbe2_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget* budget = (struct budget*) fe->dvb->priv; - u32 div; - u8 data[4]; - struct i2c_msg msg = { .addr = 0x62, .flags = 0, .buf = data, .len = sizeof(data) }; - - div = (c->frequency + 35937500 + 31250) / 62500; - - data[0] = (div >> 8) & 0x7f; - data[1] = div & 0xff; - data[2] = 0x85 | ((div >> 10) & 0x60); - data[3] = (c->frequency < 174000000 ? 0x88 : c->frequency < 470000000 ? 0x84 : 0x81); - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer (&budget->i2c_adap, &msg, 1) != 1) return -EIO; - return 0; -} - -static struct ves1820_config alps_tdbe2_config = { - .demod_address = 0x09, - .xin = 57840000UL, - .invert = 1, - .selagc = VES1820_SELAGC_SIGNAMPERR, -}; - -static int grundig_29504_401_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget *budget = fe->dvb->priv; - u8 *tuner_addr = fe->tuner_priv; - u32 div; - u8 cfg, cpump, band_select; - u8 data[4]; - struct i2c_msg msg = { .flags = 0, .buf = data, .len = sizeof(data) }; - - if (tuner_addr) - msg.addr = *tuner_addr; - else - msg.addr = 0x61; - - div = (36125000 + c->frequency) / 166666; - - cfg = 0x88; - - if (c->frequency < 175000000) - cpump = 2; - else if (c->frequency < 390000000) - cpump = 1; - else if (c->frequency < 470000000) - cpump = 2; - else if (c->frequency < 750000000) - cpump = 1; - else - cpump = 3; - - if (c->frequency < 175000000) - band_select = 0x0e; - else if (c->frequency < 470000000) - band_select = 0x05; - else - band_select = 0x03; - - data[0] = (div >> 8) & 0x7f; - data[1] = div & 0xff; - data[2] = ((div >> 10) & 0x60) | cfg; - data[3] = (cpump << 6) | band_select; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer (&budget->i2c_adap, &msg, 1) != 1) return -EIO; - return 0; -} - -static struct l64781_config grundig_29504_401_config = { - .demod_address = 0x55, -}; - -static struct l64781_config grundig_29504_401_config_activy = { - .demod_address = 0x54, -}; - -static u8 tuner_address_grundig_29504_401_activy = 0x60; - -static int grundig_29504_451_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget* budget = (struct budget*) fe->dvb->priv; - u32 div; - u8 data[4]; - struct i2c_msg msg = { .addr = 0x61, .flags = 0, .buf = data, .len = sizeof(data) }; - - div = c->frequency / 125; - data[0] = (div >> 8) & 0x7f; - data[1] = div & 0xff; - data[2] = 0x8e; - data[3] = 0x00; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer (&budget->i2c_adap, &msg, 1) != 1) return -EIO; - return 0; -} - -static struct tda8083_config grundig_29504_451_config = { - .demod_address = 0x68, -}; - -static int s5h1420_tuner_set_params(struct dvb_frontend *fe) -{ - struct dtv_frontend_properties *c = &fe->dtv_property_cache; - struct budget* budget = (struct budget*) fe->dvb->priv; - u32 div; - u8 data[4]; - struct i2c_msg msg = { .addr = 0x61, .flags = 0, .buf = data, .len = sizeof(data) }; - - div = c->frequency / 1000; - data[0] = (div >> 8) & 0x7f; - data[1] = div & 0xff; - data[2] = 0xc2; - - if (div < 1450) - data[3] = 0x00; - else if (div < 1850) - data[3] = 0x40; - else if (div < 2000) - data[3] = 0x80; - else - data[3] = 0xc0; - - if (fe->ops.i2c_gate_ctrl) - fe->ops.i2c_gate_ctrl(fe, 1); - if (i2c_transfer (&budget->i2c_adap, &msg, 1) != 1) return -EIO; - - return 0; -} - -static struct s5h1420_config s5h1420_config = { - .demod_address = 0x53, - .invert = 1, - .cdclk_polarity = 1, -}; - -static struct tda10086_config tda10086_config = { - .demod_address = 0x0e, - .invert = 0, - .diseqc_tone = 1, - .xtal_freq = TDA10086_XTAL_16M, -}; - -static const struct stv0299_config alps_bsru6_config_activy = { - .demod_address = 0x68, - .inittab = alps_bsru6_inittab, - .mclk = 88000000UL, - .invert = 1, - .op0_off = 1, - .min_delay_ms = 100, - .set_symbol_rate = alps_bsru6_set_symbol_rate, -}; - -static const struct stv0299_config alps_bsbe1_config_activy = { - .demod_address = 0x68, - .inittab = alps_bsbe1_inittab, - .mclk = 88000000UL, - .invert = 1, - .op0_off = 1, - .min_delay_ms = 100, - .set_symbol_rate = alps_bsbe1_set_symbol_rate, -}; - -static int alps_tdhd1_204_request_firmware(struct dvb_frontend *fe, const struct firmware **fw, char *name) -{ - struct budget *budget = (struct budget *)fe->dvb->priv; - - return request_firmware(fw, name, &budget->dev->pci->dev); -} - - -static int i2c_readreg(struct i2c_adapter *i2c, u8 adr, u8 reg) -{ - u8 val; - struct i2c_msg msg[] = { - { .addr = adr, .flags = 0, .buf = ®, .len = 1 }, - { .addr = adr, .flags = I2C_M_RD, .buf = &val, .len = 1 } - }; - - return (i2c_transfer(i2c, msg, 2) != 2) ? -EIO : val; -} - -static u8 read_pwm(struct budget* budget) -{ - u8 b = 0xff; - u8 pwm; - struct i2c_msg msg[] = { { .addr = 0x50,.flags = 0,.buf = &b,.len = 1 }, - { .addr = 0x50,.flags = I2C_M_RD,.buf = &pwm,.len = 1} }; - - if ((i2c_transfer(&budget->i2c_adap, msg, 2) != 2) || (pwm == 0xff)) - pwm = 0x48; - - return pwm; -} - -static struct stv090x_config tt1600_stv090x_config = { - .device = STV0903, - .demod_mode = STV090x_SINGLE, - .clk_mode = STV090x_CLK_EXT, - - .xtal = 13500000, - .address = 0x68, - - .ts1_mode = STV090x_TSMODE_DVBCI, - .ts2_mode = STV090x_TSMODE_SERIAL_CONTINUOUS, - - .repeater_level = STV090x_RPTLEVEL_16, - - .tuner_init = NULL, - .tuner_sleep = NULL, - .tuner_set_mode = NULL, - .tuner_set_frequency = NULL, - .tuner_get_frequency = NULL, - .tuner_set_bandwidth = NULL, - .tuner_get_bandwidth = NULL, - .tuner_set_bbgain = NULL, - .tuner_get_bbgain = NULL, - .tuner_set_refclk = NULL, - .tuner_get_status = NULL, -}; - -static struct stv6110x_config tt1600_stv6110x_config = { - .addr = 0x60, - .refclk = 27000000, - .clk_div = 2, -}; - -static struct isl6423_config tt1600_isl6423_config = { - .current_max = SEC_CURRENT_515m, - .curlim = SEC_CURRENT_LIM_ON, - .mod_extern = 1, - .addr = 0x08, -}; - -static void frontend_init(struct budget *budget) -{ - (void)alps_bsbe1_config; /* avoid warning */ - - switch(budget->dev->pci->subsystem_device) { - case 0x1003: // Hauppauge/TT Nova budget (stv0299/ALPS BSRU6(tsa5059) OR ves1893/ALPS BSRV2(sp5659)) - case 0x1013: - // try the ALPS BSRV2 first of all - budget->dvb_frontend = dvb_attach(ves1x93_attach, &alps_bsrv2_config, &budget->i2c_adap); - if (budget->dvb_frontend) { - budget->dvb_frontend->ops.tuner_ops.set_params = alps_bsrv2_tuner_set_params; - budget->dvb_frontend->ops.diseqc_send_master_cmd = budget_diseqc_send_master_cmd; - budget->dvb_frontend->ops.diseqc_send_burst = budget_diseqc_send_burst; - budget->dvb_frontend->ops.set_tone = budget_set_tone; - break; - } - - // try the ALPS BSRU6 now - budget->dvb_frontend = dvb_attach(stv0299_attach, &alps_bsru6_config, &budget->i2c_adap); - if (budget->dvb_frontend) { - budget->dvb_frontend->ops.tuner_ops.set_params = alps_bsru6_tuner_set_params; - budget->dvb_frontend->tuner_priv = &budget->i2c_adap; - if (budget->dev->pci->subsystem_device == 0x1003 && diseqc_method == 0) { - budget->dvb_frontend->ops.diseqc_send_master_cmd = budget_diseqc_send_master_cmd; - budget->dvb_frontend->ops.diseqc_send_burst = budget_diseqc_send_burst; - budget->dvb_frontend->ops.set_tone = budget_set_tone; - } - break; - } - break; - - case 0x1004: // Hauppauge/TT DVB-C budget (ves1820/ALPS TDBE2(sp5659)) - - budget->dvb_frontend = dvb_attach(ves1820_attach, &alps_tdbe2_config, &budget->i2c_adap, read_pwm(budget)); - if (budget->dvb_frontend) { - budget->dvb_frontend->ops.tuner_ops.set_params = alps_tdbe2_tuner_set_params; - break; - } - break; - - case 0x1005: // Hauppauge/TT Nova-T budget (L64781/Grundig 29504-401(tsa5060)) - - budget->dvb_frontend = dvb_attach(l64781_attach, &grundig_29504_401_config, &budget->i2c_adap); - if (budget->dvb_frontend) { - budget->dvb_frontend->ops.tuner_ops.set_params = grundig_29504_401_tuner_set_params; - budget->dvb_frontend->tuner_priv = NULL; - break; - } - break; - - case 0x4f52: /* Cards based on Philips Semi Sylt PCI ref. design */ - budget->dvb_frontend = dvb_attach(stv0299_attach, &alps_bsru6_config, &budget->i2c_adap); - if (budget->dvb_frontend) { - printk(KERN_INFO "budget: tuner ALPS BSRU6 in Philips Semi. Sylt detected\n"); - budget->dvb_frontend->ops.tuner_ops.set_params = alps_bsru6_tuner_set_params; - budget->dvb_frontend->tuner_priv = &budget->i2c_adap; - break; - } - break; - - case 0x4f60: /* Fujitsu Siemens Activy Budget-S PCI rev AL (stv0299/tsa5059) */ - { - int subtype = i2c_readreg(&budget->i2c_adap, 0x50, 0x67); - - if (subtype < 0) - break; - /* fixme: find a better way to identify the card */ - if (subtype < 0x36) { - /* assume ALPS BSRU6 */ - budget->dvb_frontend = dvb_attach(stv0299_attach, &alps_bsru6_config_activy, &budget->i2c_adap); - if (budget->dvb_frontend) { - printk(KERN_INFO "budget: tuner ALPS BSRU6 detected\n"); - budget->dvb_frontend->ops.tuner_ops.set_params = alps_bsru6_tuner_set_params; - budget->dvb_frontend->tuner_priv = &budget->i2c_adap; - budget->dvb_frontend->ops.set_voltage = siemens_budget_set_voltage; - budget->dvb_frontend->ops.dishnetwork_send_legacy_command = NULL; - break; - } - } else { - /* assume ALPS BSBE1 */ - /* reset tuner */ - saa7146_setgpio(budget->dev, 3, SAA7146_GPIO_OUTLO); - msleep(50); - saa7146_setgpio(budget->dev, 3, SAA7146_GPIO_OUTHI); - msleep(250); - budget->dvb_frontend = dvb_attach(stv0299_attach, &alps_bsbe1_config_activy, &budget->i2c_adap); - if (budget->dvb_frontend) { - printk(KERN_INFO "budget: tuner ALPS BSBE1 detected\n"); - budget->dvb_frontend->ops.tuner_ops.set_params = alps_bsbe1_tuner_set_params; - budget->dvb_frontend->tuner_priv = &budget->i2c_adap; - budget->dvb_frontend->ops.set_voltage = siemens_budget_set_voltage; - budget->dvb_frontend->ops.dishnetwork_send_legacy_command = NULL; - break; - } - } - break; - } - - case 0x4f61: // Fujitsu Siemens Activy Budget-S PCI rev GR (tda8083/Grundig 29504-451(tsa5522)) - budget->dvb_frontend = dvb_attach(tda8083_attach, &grundig_29504_451_config, &budget->i2c_adap); - if (budget->dvb_frontend) { - budget->dvb_frontend->ops.tuner_ops.set_params = grundig_29504_451_tuner_set_params; - budget->dvb_frontend->ops.set_voltage = siemens_budget_set_voltage; - budget->dvb_frontend->ops.dishnetwork_send_legacy_command = NULL; - } - break; - - case 0x5f60: /* Fujitsu Siemens Activy Budget-T PCI rev AL (tda10046/ALPS TDHD1-204A) */ - budget->dvb_frontend = dvb_attach(tda10046_attach, &alps_tdhd1_204a_config, &budget->i2c_adap); - if (budget->dvb_frontend) { - budget->dvb_frontend->ops.tuner_ops.set_params = alps_tdhd1_204a_tuner_set_params; - budget->dvb_frontend->tuner_priv = &budget->i2c_adap; - } - break; - - case 0x5f61: /* Fujitsu Siemens Activy Budget-T PCI rev GR (L64781/Grundig 29504-401(tsa5060)) */ - budget->dvb_frontend = dvb_attach(l64781_attach, &grundig_29504_401_config_activy, &budget->i2c_adap); - if (budget->dvb_frontend) { - budget->dvb_frontend->tuner_priv = &tuner_address_grundig_29504_401_activy; - budget->dvb_frontend->ops.tuner_ops.set_params = grundig_29504_401_tuner_set_params; - } - break; - - case 0x1016: // Hauppauge/TT Nova-S SE (samsung s5h1420/????(tda8260)) - { - struct dvb_frontend *fe; - - fe = dvb_attach(s5h1420_attach, &s5h1420_config, &budget->i2c_adap); - if (fe) { - fe->ops.tuner_ops.set_params = s5h1420_tuner_set_params; - budget->dvb_frontend = fe; - if (dvb_attach(lnbp21_attach, fe, &budget->i2c_adap, - 0, 0) == NULL) { - printk("%s: No LNBP21 found!\n", __func__); - goto error_out; - } - break; - } - } - fallthrough; - case 0x1018: // TT Budget-S-1401 (philips tda10086/philips tda8262) - { - struct dvb_frontend *fe; - - // gpio2 is connected to CLB - reset it + leave it high - saa7146_setgpio(budget->dev, 2, SAA7146_GPIO_OUTLO); - msleep(1); - saa7146_setgpio(budget->dev, 2, SAA7146_GPIO_OUTHI); - msleep(1); - - fe = dvb_attach(tda10086_attach, &tda10086_config, &budget->i2c_adap); - if (fe) { - budget->dvb_frontend = fe; - if (dvb_attach(tda826x_attach, fe, 0x60, - &budget->i2c_adap, 0) == NULL) - printk("%s: No tda826x found!\n", __func__); - if (dvb_attach(lnbp21_attach, fe, - &budget->i2c_adap, 0, 0) == NULL) { - printk("%s: No LNBP21 found!\n", __func__); - goto error_out; - } - break; - } - } - fallthrough; - - case 0x101c: { /* TT S2-1600 */ - const struct stv6110x_devctl *ctl; - saa7146_setgpio(budget->dev, 2, SAA7146_GPIO_OUTLO); - msleep(50); - saa7146_setgpio(budget->dev, 2, SAA7146_GPIO_OUTHI); - msleep(250); - - budget->dvb_frontend = dvb_attach(stv090x_attach, - &tt1600_stv090x_config, - &budget->i2c_adap, - STV090x_DEMODULATOR_0); - - if (budget->dvb_frontend) { - - ctl = dvb_attach(stv6110x_attach, - budget->dvb_frontend, - &tt1600_stv6110x_config, - &budget->i2c_adap); - - if (ctl) { - tt1600_stv090x_config.tuner_init = ctl->tuner_init; - tt1600_stv090x_config.tuner_sleep = ctl->tuner_sleep; - tt1600_stv090x_config.tuner_set_mode = ctl->tuner_set_mode; - tt1600_stv090x_config.tuner_set_frequency = ctl->tuner_set_frequency; - tt1600_stv090x_config.tuner_get_frequency = ctl->tuner_get_frequency; - tt1600_stv090x_config.tuner_set_bandwidth = ctl->tuner_set_bandwidth; - tt1600_stv090x_config.tuner_get_bandwidth = ctl->tuner_get_bandwidth; - tt1600_stv090x_config.tuner_set_bbgain = ctl->tuner_set_bbgain; - tt1600_stv090x_config.tuner_get_bbgain = ctl->tuner_get_bbgain; - tt1600_stv090x_config.tuner_set_refclk = ctl->tuner_set_refclk; - tt1600_stv090x_config.tuner_get_status = ctl->tuner_get_status; - - /* call the init function once to initialize - tuner's clock output divider and demod's - master clock */ - if (budget->dvb_frontend->ops.init) - budget->dvb_frontend->ops.init(budget->dvb_frontend); - - if (dvb_attach(isl6423_attach, - budget->dvb_frontend, - &budget->i2c_adap, - &tt1600_isl6423_config) == NULL) { - printk(KERN_ERR "%s: No Intersil ISL6423 found!\n", __func__); - goto error_out; - } - } else { - printk(KERN_ERR "%s: No STV6110(A) Silicon Tuner found!\n", __func__); - goto error_out; - } - } - } - break; - - case 0x1020: { /* Omicom S2 */ - const struct stv6110x_devctl *ctl; - saa7146_setgpio(budget->dev, 2, SAA7146_GPIO_OUTLO); - msleep(50); - saa7146_setgpio(budget->dev, 2, SAA7146_GPIO_OUTHI); - msleep(250); - - budget->dvb_frontend = dvb_attach(stv090x_attach, - &tt1600_stv090x_config, - &budget->i2c_adap, - STV090x_DEMODULATOR_0); - - if (budget->dvb_frontend) { - printk(KERN_INFO "budget: Omicom S2 detected\n"); - - ctl = dvb_attach(stv6110x_attach, - budget->dvb_frontend, - &tt1600_stv6110x_config, - &budget->i2c_adap); - - if (ctl) { - tt1600_stv090x_config.tuner_init = ctl->tuner_init; - tt1600_stv090x_config.tuner_sleep = ctl->tuner_sleep; - tt1600_stv090x_config.tuner_set_mode = ctl->tuner_set_mode; - tt1600_stv090x_config.tuner_set_frequency = ctl->tuner_set_frequency; - tt1600_stv090x_config.tuner_get_frequency = ctl->tuner_get_frequency; - tt1600_stv090x_config.tuner_set_bandwidth = ctl->tuner_set_bandwidth; - tt1600_stv090x_config.tuner_get_bandwidth = ctl->tuner_get_bandwidth; - tt1600_stv090x_config.tuner_set_bbgain = ctl->tuner_set_bbgain; - tt1600_stv090x_config.tuner_get_bbgain = ctl->tuner_get_bbgain; - tt1600_stv090x_config.tuner_set_refclk = ctl->tuner_set_refclk; - tt1600_stv090x_config.tuner_get_status = ctl->tuner_get_status; - - /* call the init function once to initialize - tuner's clock output divider and demod's - master clock */ - if (budget->dvb_frontend->ops.init) - budget->dvb_frontend->ops.init(budget->dvb_frontend); - - if (dvb_attach(lnbh24_attach, - budget->dvb_frontend, - &budget->i2c_adap, - LNBH24_PCL | LNBH24_TTX, - LNBH24_TEN, 0x14>>1) == NULL) { - printk(KERN_ERR - "No LNBH24 found!\n"); - goto error_out; - } - } else { - printk(KERN_ERR "%s: No STV6110(A) Silicon Tuner found!\n", __func__); - goto error_out; - } - } - } - break; - } - - if (budget->dvb_frontend == NULL) { - printk("budget: A frontend driver was not found for device [%04x:%04x] subsystem [%04x:%04x]\n", - budget->dev->pci->vendor, - budget->dev->pci->device, - budget->dev->pci->subsystem_vendor, - budget->dev->pci->subsystem_device); - } else { - if (dvb_register_frontend(&budget->dvb_adapter, budget->dvb_frontend)) - goto error_out; - } - return; - -error_out: - printk("budget: Frontend registration failed!\n"); - dvb_frontend_detach(budget->dvb_frontend); - budget->dvb_frontend = NULL; - return; -} - -static int budget_attach (struct saa7146_dev* dev, struct saa7146_pci_extension_data *info) -{ - struct budget *budget = NULL; - int err; - - budget = kmalloc(sizeof(struct budget), GFP_KERNEL); - if( NULL == budget ) { - return -ENOMEM; - } - - dprintk(2, "dev:%p, info:%p, budget:%p\n", dev, info, budget); - - dev->ext_priv = budget; - - err = ttpci_budget_init(budget, dev, info, THIS_MODULE, adapter_nr); - if (err) { - printk("==> failed\n"); - kfree (budget); - return err; - } - - budget->dvb_adapter.priv = budget; - frontend_init(budget); - - ttpci_budget_init_hooks(budget); - - return 0; -} - -static int budget_detach (struct saa7146_dev* dev) -{ - struct budget *budget = (struct budget*) dev->ext_priv; - int err; - - if (budget->dvb_frontend) { - dvb_unregister_frontend(budget->dvb_frontend); - dvb_frontend_detach(budget->dvb_frontend); - } - - err = ttpci_budget_deinit (budget); - - kfree (budget); - dev->ext_priv = NULL; - - return err; -} - -static struct saa7146_extension budget_extension; - -MAKE_BUDGET_INFO(ttbs, "TT-Budget/WinTV-NOVA-S PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttbc, "TT-Budget/WinTV-NOVA-C PCI", BUDGET_TT); -MAKE_BUDGET_INFO(ttbt, "TT-Budget/WinTV-NOVA-T PCI", BUDGET_TT); -MAKE_BUDGET_INFO(satel, "SATELCO Multimedia PCI", BUDGET_TT_HW_DISEQC); -MAKE_BUDGET_INFO(ttbs1401, "TT-Budget-S-1401 PCI", BUDGET_TT); -MAKE_BUDGET_INFO(tt1600, "TT-Budget S2-1600 PCI", BUDGET_TT); -MAKE_BUDGET_INFO(fsacs0, "Fujitsu Siemens Activy Budget-S PCI (rev GR/grundig frontend)", BUDGET_FS_ACTIVY); -MAKE_BUDGET_INFO(fsacs1, "Fujitsu Siemens Activy Budget-S PCI (rev AL/alps frontend)", BUDGET_FS_ACTIVY); -MAKE_BUDGET_INFO(fsact, "Fujitsu Siemens Activy Budget-T PCI (rev GR/Grundig frontend)", BUDGET_FS_ACTIVY); -MAKE_BUDGET_INFO(fsact1, "Fujitsu Siemens Activy Budget-T PCI (rev AL/ALPS TDHD1-204A)", BUDGET_FS_ACTIVY); -MAKE_BUDGET_INFO(omicom, "Omicom S2 PCI", BUDGET_TT); -MAKE_BUDGET_INFO(sylt, "Philips Semi Sylt PCI", BUDGET_TT_HW_DISEQC); - -static const struct pci_device_id pci_tbl[] = { - MAKE_EXTENSION_PCI(ttbs, 0x13c2, 0x1003), - MAKE_EXTENSION_PCI(ttbc, 0x13c2, 0x1004), - MAKE_EXTENSION_PCI(ttbt, 0x13c2, 0x1005), - MAKE_EXTENSION_PCI(satel, 0x13c2, 0x1013), - MAKE_EXTENSION_PCI(ttbs, 0x13c2, 0x1016), - MAKE_EXTENSION_PCI(ttbs1401, 0x13c2, 0x1018), - MAKE_EXTENSION_PCI(tt1600, 0x13c2, 0x101c), - MAKE_EXTENSION_PCI(fsacs1,0x1131, 0x4f60), - MAKE_EXTENSION_PCI(fsacs0,0x1131, 0x4f61), - MAKE_EXTENSION_PCI(fsact1, 0x1131, 0x5f60), - MAKE_EXTENSION_PCI(fsact, 0x1131, 0x5f61), - MAKE_EXTENSION_PCI(omicom, 0x14c4, 0x1020), - MAKE_EXTENSION_PCI(sylt, 0x1131, 0x4f52), - { - .vendor = 0, - } -}; - -MODULE_DEVICE_TABLE(pci, pci_tbl); - -static struct saa7146_extension budget_extension = { - .name = "budget dvb", - .flags = SAA7146_USE_I2C_IRQ, - - .module = THIS_MODULE, - .pci_tbl = pci_tbl, - .attach = budget_attach, - .detach = budget_detach, - - .irq_mask = MASK_10, - .irq_func = ttpci_budget_irq10_handler, -}; - -static int __init budget_init(void) -{ - return saa7146_register_extension(&budget_extension); -} - -static void __exit budget_exit(void) -{ - saa7146_unregister_extension(&budget_extension); -} - -module_init(budget_init); -module_exit(budget_exit); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Ralph Metzler, Marcus Metzler, Michael Hunold, others"); -MODULE_DESCRIPTION("driver for the SAA7146 based so-called budget PCI DVB cards by Siemens, Technotrend, Hauppauge"); diff --git a/drivers/staging/media/deprecated/saa7146/ttpci/budget.h b/drivers/staging/media/deprecated/saa7146/ttpci/budget.h deleted file mode 100644 index 82cc0df492b3..000000000000 --- a/drivers/staging/media/deprecated/saa7146/ttpci/budget.h +++ /dev/null @@ -1,129 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ - -#ifndef __BUDGET_DVB__ -#define __BUDGET_DVB__ - -#include <media/dvb_frontend.h> -#include <media/dvbdev.h> -#include <media/demux.h> -#include <media/dvb_demux.h> -#include <media/dmxdev.h> -#include <media/dvb_net.h> - -#include <linux/module.h> -#include <linux/mutex.h> - -#include "../common/saa7146.h" - -extern int budget_debug; - -#ifdef dprintk -#undef dprintk -#endif - -#define dprintk(level, fmt, arg...) do { \ - if (level & budget_debug) \ - printk(KERN_DEBUG KBUILD_MODNAME ": %s(): " fmt, \ - __func__, ##arg); \ -} while (0) - -#define TS_SIZE 188 - -struct budget_info { - char *name; - int type; -}; - -/* place to store all the necessary device information */ -struct budget { - - /* devices */ - struct dvb_device dvb_dev; - struct dvb_net dvb_net; - - struct saa7146_dev *dev; - - struct i2c_adapter i2c_adap; - struct budget_info *card; - - unsigned char *grabbing; - struct saa7146_pgtable pt; - - struct tasklet_struct fidb_tasklet; - struct tasklet_struct vpe_tasklet; - - struct dmxdev dmxdev; - struct dvb_demux demux; - - struct dmx_frontend hw_frontend; - struct dmx_frontend mem_frontend; - - int ci_present; - int video_port; - - u32 buffer_width; - u32 buffer_height; - u32 buffer_size; - u32 buffer_warning_threshold; - u32 buffer_warnings; - unsigned long buffer_warning_time; - - u32 ttbp; - int feeding; - - spinlock_t feedlock; - - spinlock_t debilock; - - struct dvb_adapter dvb_adapter; - struct dvb_frontend *dvb_frontend; - int (*read_fe_status)(struct dvb_frontend *fe, enum fe_status *status); - int fe_synced; - - void *priv; -}; - -#define MAKE_BUDGET_INFO(x_var,x_name,x_type) \ -static struct budget_info x_var ## _info = { \ - .name=x_name, \ - .type=x_type }; \ -static struct saa7146_pci_extension_data x_var = { \ - .ext_priv = &x_var ## _info, \ - .ext = &budget_extension }; - -#define BUDGET_TT 0 -#define BUDGET_TT_HW_DISEQC 1 -#define BUDGET_PATCH 3 -#define BUDGET_FS_ACTIVY 4 -#define BUDGET_CIN1200S 5 -#define BUDGET_CIN1200C 6 -#define BUDGET_CIN1200T 7 -#define BUDGET_KNC1S 8 -#define BUDGET_KNC1C 9 -#define BUDGET_KNC1T 10 -#define BUDGET_KNC1SP 11 -#define BUDGET_KNC1CP 12 -#define BUDGET_KNC1TP 13 -#define BUDGET_TVSTAR 14 -#define BUDGET_CIN1200C_MK3 15 -#define BUDGET_KNC1C_MK3 16 -#define BUDGET_KNC1CP_MK3 17 -#define BUDGET_KNC1S2 18 -#define BUDGET_KNC1C_TDA10024 19 - -#define BUDGET_VIDEO_PORTA 0 -#define BUDGET_VIDEO_PORTB 1 - -extern int ttpci_budget_init(struct budget *budget, struct saa7146_dev *dev, - struct saa7146_pci_extension_data *info, - struct module *owner, short *adapter_nums); -extern void ttpci_budget_init_hooks(struct budget *budget); -extern int ttpci_budget_deinit(struct budget *budget); -extern void ttpci_budget_irq10_handler(struct saa7146_dev *dev, u32 * isr); -extern void ttpci_budget_set_video_port(struct saa7146_dev *dev, int video_port); -extern int ttpci_budget_debiread(struct budget *budget, u32 config, int addr, int count, - int uselocks, int nobusyloop); -extern int ttpci_budget_debiwrite(struct budget *budget, u32 config, int addr, int count, u32 value, - int uselocks, int nobusyloop); - -#endif -- 2.39.0
