Re: [PATCH v6 5/8] dt-bindings: media: add TI DS90UB960 FPD-Link III Deserializer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Jan 09, 2023 at 10:30:13AM +0200, Tomi Valkeinen wrote:
> On 08/01/2023 05:23, Laurent Pinchart wrote:
> > Hi Tomi,
> > 
> > Thank you for the patch.
> > 
> > On Thu, Jan 05, 2023 at 04:03:04PM +0200, Tomi Valkeinen wrote:
> >> Add DT bindings for TI DS90UB960 FPD-Link III Deserializer.
> >>
> >> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxxxxxxxxxxxx>
> >> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> >> ---
> >>   .../bindings/media/i2c/ti,ds90ub960.yaml      | 402 ++++++++++++++++++
> >>   1 file changed, 402 insertions(+)
> >>   create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
> >> new file mode 100644
> >> index 000000000000..664799ae55be
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub960.yaml
> >> @@ -0,0 +1,402 @@
> >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub960.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Texas Instruments DS90UB9XX Family FPD-Link Deserializer Hubs
> >> +
> >> +maintainers:
> >> +  - Tomi Valkeinen <tomi.valkeinen@xxxxxxxxxxxxxxxx>
> >> +
> >> +description:
> >> +  The TI DS90UB9XX devices are FPD-Link video deserializers with I2C and GPIO
> >> +  forwarding.
> >> +
> >> +properties:
> >> +  compatible:
> >> +    enum:
> >> +      - ti,ds90ub960-q1
> >> +      - ti,ds90ub9702-q1
> >> +
> >> +  reg:
> >> +    maxItems: 1
> >> +
> >> +  clocks:
> >> +    maxItems: 1
> >> +    description:
> >> +      Reference clock connected to the REFCLK pin.
> >> +
> >> +  clock-names:
> >> +    items:
> >> +      - const: refclk
> >> +
> >> +  powerdown-gpios:
> >> +    maxItems: 1
> >> +    description:
> >> +      Specifier for the GPIO connected to the PDB pin.
> >> +
> >> +  i2c-alias-pool:
> >> +    $ref: /schemas/types.yaml#/definitions/uint16-array
> >> +    description:
> >> +      I2C alias pool is a pool of I2C addresses on the main I2C bus that can be
> >> +      used to access the remote peripherals on the serializer's I2C bus. The
> >> +      addresses must be available, not used by any other peripheral. Each
> >> +      remote peripheral is assigned an alias from the pool, and transactions to
> >> +      that address will be forwarded to the remote peripheral, with the address
> >> +      translated to the remote peripheral's real address. This property is not
> >> +      needed if there are no I2C addressable remote peripherals.
> >> +
> >> +  links:
> >> +    type: object
> >> +    additionalProperties: false
> >> +
> >> +    properties:
> >> +      '#address-cells':
> >> +        const: 1
> >> +
> >> +      '#size-cells':
> >> +        const: 0
> >> +
> >> +      ti,manual-strobe:
> >> +        type: boolean
> >> +        description:
> >> +          Enable manual strobe position and EQ level
> >> +
> >> +    patternProperties:
> >> +      '^link@[0-3]$':
> >> +        type: object
> >> +        additionalProperties: false
> >> +        properties:
> >> +          reg:
> >> +            description: The link number
> >> +            maxItems: 1
> >> +
> >> +          i2c-alias:
> >> +            description:
> >> +              The I2C address used for the serializer. Transactions to this
> >> +              address on the I2C bus where the deserializer resides are
> >> +              forwarded to the serializer.
> >> +
> >> +          ti,rx-mode:
> >> +            $ref: /schemas/types.yaml#/definitions/uint32
> >> +            enum:
> >> +              - 0 # RAW10
> >> +              - 1 # RAW12 HF
> >> +              - 2 # RAW12 LF
> >> +              - 3 # CSI2 SYNC
> >> +              - 4 # CSI2 NON-SYNC
> >> +            description:
> >> +              FPD-Link Input Mode. This should reflect the hardware and the
> >> +              default mode of the connected camera module.
> > 
> > As the remote device may not be a camera, I'd write "of the connected
> > device" or "of the connected serializer".
> 
> I was trying to include the sensor also in the "camera module", as the 
> sensor's "normal" pixel cloud would affect RAW modes (HF/LF). Perhaps 
> "connected device" covers this.
> 
> >> +
> >> +          ti,cdr-mode:
> >> +            $ref: /schemas/types.yaml#/definitions/uint32
> >> +            enum:
> >> +              - 0 # FPD-Link III
> >> +              - 1 # FPD-Link IV
> >> +            description:
> >> +              FPD-Link CDR Mode. This should reflect the hardware and the
> >> +              default mode of the connected camera module.
> >> +
> >> +          ti,strobe-pos:
> >> +            $ref: /schemas/types.yaml#/definitions/int32
> >> +            minimum: -13
> >> +            maximum: 13
> >> +            description: Manual strobe position
> >> +
> >> +          ti,eq-level:
> >> +            $ref: /schemas/types.yaml#/definitions/uint32
> >> +            maximum: 14
> >> +            description: Manual EQ level
> >> +
> >> +          serializer:
> >> +            type: object
> >> +            description: FPD-Link Serializer node
> >> +
> >> +        required:
> >> +          - reg
> >> +          - i2c-alias
> >> +          - ti,rx-mode
> >> +          - serializer
> >> +
> >> +  ports:
> >> +    $ref: /schemas/graph.yaml#/properties/ports
> >> +
> >> +    properties:
> >> +      port@0:
> >> +        $ref: /schemas/graph.yaml#/$defs/port-base
> >> +        unevaluatedProperties: false
> >> +        description: FPD-Link input 0
> >> +
> >> +        properties:
> >> +          endpoint:
> >> +            $ref: /schemas/media/video-interfaces.yaml#
> >> +            unevaluatedProperties: false
> >> +            description:
> >> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> >> +              hsync-active and vsync-active must be defined.
> >> +
> >> +      port@1:
> >> +        $ref: /schemas/graph.yaml#/$defs/port-base
> >> +        unevaluatedProperties: false
> >> +        description: FPD-Link input 1
> >> +
> >> +        properties:
> >> +          endpoint:
> >> +            $ref: /schemas/media/video-interfaces.yaml#
> >> +            unevaluatedProperties: false
> >> +            description:
> >> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> >> +              hsync-active and vsync-active must be defined.
> >> +
> >> +      port@2:
> >> +        $ref: /schemas/graph.yaml#/$defs/port-base
> >> +        unevaluatedProperties: false
> >> +        description: FPD-Link input 2
> >> +
> >> +        properties:
> >> +          endpoint:
> >> +            $ref: /schemas/media/video-interfaces.yaml#
> >> +            unevaluatedProperties: false
> >> +            description:
> >> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> >> +              hsync-active and vsync-active must be defined.
> >> +
> >> +      port@3:
> >> +        $ref: /schemas/graph.yaml#/$defs/port-base
> >> +        unevaluatedProperties: false
> >> +        description: FPD-Link input 3
> >> +
> >> +        properties:
> >> +          endpoint:
> >> +            $ref: /schemas/media/video-interfaces.yaml#
> >> +            unevaluatedProperties: false
> >> +            description:
> >> +              Endpoint for FPD-Link port. If the RX mode for this port is RAW,
> >> +              hsync-active and vsync-active must be defined.
> >> +
> >> +      port@4:
> >> +        $ref: /schemas/graph.yaml#/$defs/port-base
> >> +        unevaluatedProperties: false
> >> +        description: CSI-2 Output 0
> >> +
> >> +        properties:
> >> +          endpoint:
> >> +            $ref: /schemas/media/video-interfaces.yaml#
> >> +            unevaluatedProperties: false
> >> +
> >> +            properties:
> >> +              data-lanes:
> >> +                minItems: 1
> >> +                maxItems: 4
> >> +
> >> +            required:
> >> +              - data-lanes
> >> +
> >> +      port@5:
> >> +        $ref: /schemas/graph.yaml#/$defs/port-base
> >> +        unevaluatedProperties: false
> >> +        description: CSI-2 Output 1
> >> +
> >> +        properties:
> >> +          endpoint:
> >> +            $ref: /schemas/media/video-interfaces.yaml#
> >> +            unevaluatedProperties: false
> >> +
> >> +            properties:
> >> +              data-lanes:
> >> +                minItems: 1
> >> +                maxItems: 4
> >> +
> >> +            required:
> >> +              - data-lanes
> > 
> > I think you need
> > 
> >      required:
> >        - port@0
> >        - port@1
> >        - port@2
> >        - port@3
> >        - port@4
> >        - port@5
> 
> Is that needed? I think often some of the ports are unused (e.g. the 
> example in this yaml file). Is it customary to still require empty port 
> nodes in the DT?

Ports are an intrinsic property of a device, they don't depend on the
device integration in the system. In this case, the UB960 has four
FPD-Link inputs and two CSI-2 outputs, that's a property of the chip.
They don't have to be connected to anything on the board, so endpooints
are optional.

-- 
Regards,

Laurent Pinchart



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux