Hi Alexander,
On Wed, Nov 23, 2022 at 09:42:10AM +0100, Alexander Stein wrote:
> Am Dienstag, 22. November 2022, 23:32:46 CET schrieb Laurent Pinchart:
> > Use the V4L2 subdev active state API to store the active format. This
> > simplifies the driver not only by dropping the imx290 current_format
> > field, but it also allows dropping the imx290 lock, replaced with the
> > state lock.
> >
> > Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > ---
> > drivers/media/i2c/imx290.c | 139 +++++++++++++++----------------------
> > 1 file changed, 56 insertions(+), 83 deletions(-)
> >
> > diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> > index 848de4c90d3b..cd2154983341 100644
> > --- a/drivers/media/i2c/imx290.c
> > +++ b/drivers/media/i2c/imx290.c
> > @@ -177,12 +177,12 @@ struct imx290 {
> > struct clk *xclk;
> > struct regmap *regmap;
> > u8 nlanes;
> > - u8 bpp;
> >
> > struct v4l2_subdev sd;
> > struct media_pad pad;
> > - struct v4l2_mbus_framefmt current_format;
> > +
> > const struct imx290_mode *current_mode;
> > + u8 bpp;
> >
> > struct regulator_bulk_data supplies[IMX290_NUM_SUPPLIES];
> > struct gpio_desc *rst_gpio;
> > @@ -192,8 +192,6 @@ struct imx290 {
> > struct v4l2_ctrl *pixel_rate;
> > struct v4l2_ctrl *hblank;
> > struct v4l2_ctrl *vblank;
> > -
> > - struct mutex lock;
> > };
> >
> > static inline struct imx290 *to_imx290(struct v4l2_subdev *_sd)
> > @@ -524,14 +522,15 @@ static int imx290_set_black_level(struct imx290
> > *imx290, black_level >> (16 - imx290->bpp), err);
> > }
> >
> > -static int imx290_write_current_format(struct imx290 *imx290)
> > +static int imx290_setup_format(struct imx290 *imx290,
> > + const struct v4l2_mbus_framefmt *format)
> > {
> > const struct imx290_regval *regs;
> > unsigned int num_regs;
> > unsigned int bpp;
> > int ret;
> >
> > - switch (imx290->current_format.code) {
> > + switch (format->code) {
> > case MEDIA_BUS_FMT_SRGGB10_1X10:
> > regs = imx290_10bit_settings;
> > num_regs = ARRAY_SIZE(imx290_10bit_settings);
> > @@ -564,12 +563,17 @@ static int imx290_set_ctrl(struct v4l2_ctrl *ctrl)
> > {
> > struct imx290 *imx290 = container_of(ctrl->handler,
> > struct imx290, ctrls);
> > + const struct v4l2_mbus_framefmt *format;
> > + struct v4l2_subdev_state *state;
> > int ret = 0;
> >
> > /* V4L2 controls values will be applied only when power is already up */
> > if (!pm_runtime_get_if_in_use(imx290->dev))
> > return 0;
> >
> > + state = v4l2_subdev_get_locked_active_state(&imx290->sd);
> > + format = v4l2_subdev_get_pad_format(&imx290->sd, state, 0);
> > +
> > switch (ctrl->id) {
> > case V4L2_CID_ANALOGUE_GAIN:
> > ret = imx290_write(imx290, IMX290_GAIN, ctrl->val, NULL);
> > @@ -646,11 +650,10 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> > int ret;
> >
> > ret = v4l2_fwnode_device_parse(imx290->dev, &props);
> > - if (ret < 0)
> > + if (ret)
>
> This is an unrelated change.
I'll drop it.
> > return ret;
> >
> > v4l2_ctrl_handler_init(&imx290->ctrls, 9);
> > - imx290->ctrls.lock = &imx290->lock;
> >
> > /*
> > * The sensor has an analog gain and a digital gain, both controlled
> > @@ -715,11 +718,6 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> > return ret;
> > }
> >
> > - mutex_lock(imx290->ctrls.lock);
> > - imx290_ctrl_update(imx290, &imx290->current_format,
> > - imx290->current_mode);
> > - mutex_unlock(imx290->ctrls.lock);
> > -
> > return 0;
> > }
> >
> > @@ -728,8 +726,10 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> > */
> >
> > /* Start streaming */
> > -static int imx290_start_streaming(struct imx290 *imx290)
> > +static int imx290_start_streaming(struct imx290 *imx290,
> > + struct v4l2_subdev_state *state)
> > {
> > + const struct v4l2_mbus_framefmt *format;
> > int ret;
> >
> > /* Set init register settings */
> > @@ -742,7 +742,8 @@ static int imx290_start_streaming(struct imx290 *imx290)
> > }
> >
> > /* Apply the register values related to current frame format */
> > - ret = imx290_write_current_format(imx290);
> > + format = v4l2_subdev_get_pad_format(&imx290->sd, state, 0);
> > + ret = imx290_setup_format(imx290, format);
> > if (ret < 0) {
> > dev_err(imx290->dev, "Could not set frame format\n");
> > return ret;
> > @@ -762,7 +763,7 @@ static int imx290_start_streaming(struct imx290 *imx290)
> > return ret;
> >
> > /* Apply customized values from user */
> > - ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler);
> > + ret = __v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler);
>
> Why is it safe to ignore the lock now? There is no user-specified lock for
> imx290->ctrls.lock, but instead imx290->ctrls._lock is set, no?
That's because the control handler and subdev state lock are the same.
The imx290_start_streaming() function starts by calling
v4l2_subdev_lock_and_get_active_state(), which takes the lock, so we
must not lock again with v4l2_ctrl_handler_setup().
> > if (ret) {
> > dev_err(imx290->dev, "Could not sync v4l2 controls\n");
> > return ret;
> > @@ -791,39 +792,32 @@ static int imx290_stop_streaming(struct imx290
> > *imx290) static int imx290_set_stream(struct v4l2_subdev *sd, int enable)
> > {
> > struct imx290 *imx290 = to_imx290(sd);
> > + struct v4l2_subdev_state *state;
> > int ret = 0;
> >
> > + state = v4l2_subdev_lock_and_get_active_state(sd);
> > +
> > if (enable) {
> > ret = pm_runtime_resume_and_get(imx290->dev);
> > if (ret < 0)
> > - goto unlock_and_return;
> > + goto unlock;
> >
> > - ret = imx290_start_streaming(imx290);
> > + ret = imx290_start_streaming(imx290, state);
> > if (ret) {
> > dev_err(imx290->dev, "Start stream failed\n");
> > pm_runtime_put(imx290->dev);
> > - goto unlock_and_return;
> > + goto unlock;
> > }
> > } else {
> > imx290_stop_streaming(imx290);
> > pm_runtime_put(imx290->dev);
> > }
> >
> > -unlock_and_return:
> > -
> > +unlock:
> > + v4l2_subdev_unlock_state(state);
> > return ret;
> > }
> >
> > -static struct v4l2_mbus_framefmt *
> > -imx290_get_pad_format(struct imx290 *imx290, struct v4l2_subdev_state
> > *state, - u32 which)
> > -{
> > - if (which == V4L2_SUBDEV_FORMAT_ACTIVE)
> > - return &imx290->current_format;
> > - else
> > - return v4l2_subdev_get_try_format(&imx290->sd, state, 0);
> > -}
> > -
> > static int imx290_enum_mbus_code(struct v4l2_subdev *sd,
> > struct v4l2_subdev_state *sd_state,
> > struct v4l2_subdev_mbus_code_enum *code)
> > @@ -858,23 +852,6 @@ static int imx290_enum_frame_size(struct v4l2_subdev
> > *sd, return 0;
> > }
> >
> > -static int imx290_get_fmt(struct v4l2_subdev *sd,
> > - struct v4l2_subdev_state *sd_state,
> > - struct v4l2_subdev_format *fmt)
> > -{
> > - struct imx290 *imx290 = to_imx290(sd);
> > - struct v4l2_mbus_framefmt *framefmt;
> > -
> > - mutex_lock(&imx290->lock);
> > -
> > - framefmt = imx290_get_pad_format(imx290, sd_state, fmt->which);
> > - fmt->format = *framefmt;
> > -
> > - mutex_unlock(&imx290->lock);
> > -
> > - return 0;
> > -}
> > -
> > static int imx290_set_fmt(struct v4l2_subdev *sd,
> > struct v4l2_subdev_state *sd_state,
> > struct v4l2_subdev_format *fmt)
> > @@ -884,8 +861,6 @@ static int imx290_set_fmt(struct v4l2_subdev *sd,
> > struct v4l2_mbus_framefmt *format;
> > unsigned int i;
> >
> > - mutex_lock(&imx290->lock);
> > -
> > mode = v4l2_find_nearest_size(imx290_modes_ptr(imx290),
> > imx290_modes_num(imx290), width, height,
> > fmt->format.width, fmt-
> >format.height);
> > @@ -903,7 +878,7 @@ static int imx290_set_fmt(struct v4l2_subdev *sd,
> > fmt->format.code = imx290_formats[i].code;
> > fmt->format.field = V4L2_FIELD_NONE;
> >
> > - format = imx290_get_pad_format(imx290, sd_state, fmt->which);
> > + format = v4l2_subdev_get_pad_format(sd, sd_state, 0);
> >
> > if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
> > imx290->current_mode = mode;
> > @@ -914,8 +889,6 @@ static int imx290_set_fmt(struct v4l2_subdev *sd,
> >
> > *format = fmt->format;
> >
> > - mutex_unlock(&imx290->lock);
> > -
> > return 0;
> > }
> >
> > @@ -923,14 +896,11 @@ static int imx290_get_selection(struct v4l2_subdev
> > *sd, struct v4l2_subdev_state *sd_state,
> > struct v4l2_subdev_selection *sel)
> > {
> > - struct imx290 *imx290 = to_imx290(sd);
> > struct v4l2_mbus_framefmt *format;
> >
> > switch (sel->target) {
> > case V4L2_SEL_TGT_CROP: {
> > - format = imx290_get_pad_format(imx290, sd_state, sel->which);
> > -
> > - mutex_lock(&imx290->lock);
> > + format = v4l2_subdev_get_pad_format(sd, sd_state, 0);
> >
> > sel->r.top = IMX920_PIXEL_ARRAY_MARGIN_TOP
> > + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT - format->height) / 2;
> > @@ -939,7 +909,6 @@ static int imx290_get_selection(struct v4l2_subdev *sd,
> > sel->r.width = format->width;
> > sel->r.height = format->height;
> >
> > - mutex_unlock(&imx290->lock);
> > return 0;
> > }
> >
> > @@ -968,11 +937,13 @@ static int imx290_get_selection(struct v4l2_subdev
> > *sd, static int imx290_entity_init_cfg(struct v4l2_subdev *subdev,
> > struct v4l2_subdev_state *sd_state)
> > {
> > - struct v4l2_subdev_format fmt = { 0 };
> > -
> > - fmt.which = sd_state ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> > - fmt.format.width = 1920;
> > - fmt.format.height = 1080;
> > + struct v4l2_subdev_format fmt = {
> > + .which = V4L2_SUBDEV_FORMAT_TRY,
> > + .format = {
> > + .width = 1920,
> > + .height = 1080,
> > + },
> > + };
> >
> > imx290_set_fmt(subdev, sd_state, &fmt);
> >
> > @@ -987,7 +958,7 @@ static const struct v4l2_subdev_pad_ops imx290_pad_ops =
> > { .init_cfg = imx290_entity_init_cfg,
> > .enum_mbus_code = imx290_enum_mbus_code,
> > .enum_frame_size = imx290_enum_frame_size,
> > - .get_fmt = imx290_get_fmt,
> > + .get_fmt = v4l2_subdev_get_fmt,
> > .set_fmt = imx290_set_fmt,
> > .get_selection = imx290_get_selection,
> > };
> > @@ -1004,20 +975,12 @@ static const struct media_entity_operations
> > imx290_subdev_entity_ops = { static int imx290_subdev_init(struct imx290
> > *imx290)
> > {
> > struct i2c_client *client = to_i2c_client(imx290->dev);
> > + const struct v4l2_mbus_framefmt *format;
> > + struct v4l2_subdev_state *state;
> > int ret;
> >
> > - /*
> > - * Initialize the frame format. In particular, imx290->current_mode
> > - * and imx290->bpp are set to defaults: imx290_calc_pixel_rate() call
> > - * below relies on these fields.
> > - */
> > - imx290_entity_init_cfg(&imx290->sd, NULL);
> > -
> > - ret = imx290_ctrl_init(imx290);
> > - if (ret < 0) {
> > - dev_err(imx290->dev, "Control initialization error %d\n", ret);
> > - return ret;
> > - }
> > + imx290->current_mode = &imx290_modes_ptr(imx290)[0];
> > + imx290->bpp = imx290_formats[0].bpp;
> >
> > v4l2_i2c_subdev_init(&imx290->sd, client, &imx290_subdev_ops);
> > imx290->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > @@ -1032,6 +995,22 @@ static int imx290_subdev_init(struct imx290 *imx290)
> > return ret;
> > }
> >
> > + ret = imx290_ctrl_init(imx290);
> > + if (ret < 0) {
> > + dev_err(imx290->dev, "Control initialization error %d\n", ret);
> > + media_entity_cleanup(&imx290->sd.entity);
> > + return ret;
> > + }
> > +
> > + imx290->sd.state_lock = imx290->ctrls.lock;
> > +
> > + v4l2_subdev_init_finalize(&imx290->sd);
> > +
> > + state = v4l2_subdev_lock_and_get_active_state(&imx290->sd);
> > + format = v4l2_subdev_get_pad_format(&imx290->sd, state, 0);
> > + imx290_ctrl_update(imx290, format, imx290->current_mode);
> > + v4l2_subdev_unlock_state(state);
>
> Do you need to check for state == NULL here?
No, v4l2_subdev_lock_and_get_active_state() can only return NULL if the
subdev driver doesn't have an active state, and
v4l2_subdev_init_finalize() guarantees it has one.
> > +
> > return 0;
> > }
> >
> > @@ -1268,12 +1247,10 @@ static int imx290_probe(struct i2c_client *client)
> > if (ret)
> > return ret;
> >
> > - mutex_init(&imx290->lock);
> > -
> > /* Initialize and register subdev. */
> > ret = imx290_subdev_init(imx290);
> > if (ret)
> > - goto err_mutex;
> > + return ret;
> >
> > ret = v4l2_async_register_subdev(&imx290->sd);
> > if (ret < 0) {
> > @@ -1305,8 +1282,6 @@ static int imx290_probe(struct i2c_client *client)
> >
> > err_subdev:
> > imx290_subdev_cleanup(imx290);
> > -err_mutex:
> > - mutex_destroy(&imx290->lock);
> >
> > return ret;
> > }
> > @@ -1319,8 +1294,6 @@ static void imx290_remove(struct i2c_client *client)
> > v4l2_async_unregister_subdev(sd);
> > imx290_subdev_cleanup(imx290);
> >
> > - mutex_destroy(&imx290->lock);
> > -
> > pm_runtime_disable(imx290->dev);
> > if (!pm_runtime_status_suspended(imx290->dev))
> > imx290_power_off(imx290->dev);
--
Regards,
Laurent Pinchart
