Depending on which order userspace makes various v4l2 calls, the sensor
might still be powered down when set_fmt is called.
What should really happen here is delay the writing of the mode-related
registers till streaming is started, but for now use the same quick fix
as the atomisp_ov2680 code and call power_up() from set_fmt() in
combination with keeping track of the power-state to avoid doing the
power-up sequence twice.
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
drivers/staging/media/atomisp/i2c/atomisp-gc0310.c | 14 ++++++++++++--
drivers/staging/media/atomisp/i2c/gc0310.h | 1 +
2 files changed, 13 insertions(+), 2 deletions(-)
diff --git a/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c b/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c
index 783f1b88ebf2..87a634bf9ff5 100644
--- a/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c
+++ b/drivers/staging/media/atomisp/i2c/atomisp-gc0310.c
@@ -786,8 +786,6 @@ static int gpio_ctrl(struct v4l2_subdev *sd, bool flag)
return ret;
}
-static int power_down(struct v4l2_subdev *sd);
-
static int power_up(struct v4l2_subdev *sd)
{
struct gc0310_device *dev = to_gc0310_sensor(sd);
@@ -800,6 +798,9 @@ static int power_up(struct v4l2_subdev *sd)
return -ENODEV;
}
+ if (dev->power_on)
+ return 0; /* Already on */
+
/* power control */
ret = power_ctrl(sd, 1);
if (ret)
@@ -820,6 +821,7 @@ static int power_up(struct v4l2_subdev *sd)
msleep(100);
+ dev->power_on = true;
return 0;
fail_gpio:
@@ -844,6 +846,9 @@ static int power_down(struct v4l2_subdev *sd)
return -ENODEV;
}
+ if (!dev->power_on)
+ return 0; /* Already off */
+
/* gpio ctrl */
ret = gpio_ctrl(sd, 0);
if (ret) {
@@ -861,6 +866,7 @@ static int power_down(struct v4l2_subdev *sd)
if (ret)
dev_err(&client->dev, "vprog failed.\n");
+ dev->power_on = false;
return ret;
}
@@ -935,6 +941,9 @@ static int gc0310_set_fmt(struct v4l2_subdev *sd,
return 0;
}
+ /* s_power has not been called yet for std v4l2 clients (camorama) */
+ power_up(sd);
+
dev_dbg(&client->dev, "%s: before gc0310_write_reg_array %s\n",
__func__, dev->res->desc);
ret = startup(sd);
@@ -1073,6 +1082,7 @@ static int gc0310_s_config(struct v4l2_subdev *sd,
* as first power on by board may not fulfill the
* power on sequqence needed by the module
*/
+ dev->power_on = true; /* force power_down() to run */
ret = power_down(sd);
if (ret) {
dev_err(&client->dev, "gc0310 power-off err.\n");
diff --git a/drivers/staging/media/atomisp/i2c/gc0310.h b/drivers/staging/media/atomisp/i2c/gc0310.h
index db643ebc3909..4b9ce681bd93 100644
--- a/drivers/staging/media/atomisp/i2c/gc0310.h
+++ b/drivers/staging/media/atomisp/i2c/gc0310.h
@@ -152,6 +152,7 @@ struct gc0310_device {
int vt_pix_clk_freq_mhz;
struct gc0310_resolution *res;
u8 type;
+ bool power_on;
};
enum gc0310_tok_type {
--
2.37.3
