Hi Dave
On Wed, Oct 05, 2022 at 04:28:08PM +0100, Dave Stevenson wrote:
> The sensor supports 8 or 10 bit readout modes, but the
> driver only supported 10 bit.
>
> Add 8 bit readout.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
> ---
> drivers/media/i2c/ov9282.c | 110 ++++++++++++++++++++++++++++++-------
> 1 file changed, 89 insertions(+), 21 deletions(-)
>
> diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
> index ec1599488f21..bc429455421e 100644
> --- a/drivers/media/i2c/ov9282.c
> +++ b/drivers/media/i2c/ov9282.c
> @@ -22,6 +22,10 @@
> #define OV9282_MODE_STANDBY 0x00
> #define OV9282_MODE_STREAMING 0x01
>
> +#define OV9282_REG_PLL_CTRL_0D 0x030d
> +#define OV9282_PLL_CTRL_0D_RAW8 0x60
> +#define OV9282_PLL_CTRL_0D_RAW10 0x50
> +
> #define OV9282_REG_TIMING_HTS 0x380c
> #define OV9282_TIMING_HTS_MAX 0x7fff
>
> @@ -49,6 +53,10 @@
> /* Group hold register */
> #define OV9282_REG_HOLD 0x3308
>
> +#define OV9282_REG_ANA_CORE_2 0x3662
> +#define OV9282_ANA_CORE2_RAW8 0x07
> +#define OV9282_ANA_CORE2_RAW10 0x05
> +
> #define OV9282_REG_TIMING_FORMAT_1 0x3820
> #define OV9282_REG_TIMING_FORMAT_2 0x3821
> #define OV9282_FLIP_BIT BIT(2)
> @@ -64,8 +72,10 @@
> #define OV9282_NUM_DATA_LANES 2
>
> /* Pixel rate */
> -#define OV9282_PIXEL_RATE (OV9282_LINK_FREQ * 2 * \
> - OV9282_NUM_DATA_LANES / 10)
> +#define OV9282_PIXEL_RATE_10BIT (OV9282_LINK_FREQ * 2 * \
> + OV9282_NUM_DATA_LANES / 10)
> +#define OV9282_PIXEL_RATE_8BIT (OV9282_LINK_FREQ * 2 * \
> + OV9282_NUM_DATA_LANES / 8)
Here you go... This can also be dyanmically calculated, but with only
2 modes and a single link_freq I guess this is fine for now
>
> /*
> * OV9282 native and active pixel array size.
> @@ -149,6 +159,7 @@ struct ov9282_mode {
> * @again_ctrl: Pointer to analog gain control
> * @vblank: Vertical blanking in lines
> * @cur_mode: Pointer to current selected sensor mode
> + * @code: Mbus code currently selected
> * @mutex: Mutex for serializing sensor controls
> * @streaming: Flag indicating streaming state
> */
> @@ -169,8 +180,10 @@ struct ov9282 {
> struct v4l2_ctrl *exp_ctrl;
> struct v4l2_ctrl *again_ctrl;
> };
> + struct v4l2_ctrl *pixel_rate;
> u32 vblank;
> const struct ov9282_mode *cur_mode;
> + u32 code;
> struct mutex mutex;
> bool streaming;
> };
> @@ -182,7 +195,6 @@ static const s64 link_freq[] = {
> /* Common registers */
> static const struct ov9282_reg common_regs[] = {
> {0x0302, 0x32},
> - {0x030d, 0x50},
> {0x030e, 0x02},
> {0x3001, 0x00},
> {0x3004, 0x00},
> @@ -514,23 +526,41 @@ static int ov9282_write_regs(struct ov9282 *ov9282,
> * ov9282_update_controls() - Update control ranges based on streaming mode
> * @ov9282: pointer to ov9282 device
> * @mode: pointer to ov9282_mode sensor mode
> + * @fmt: pointer to the requested mode
> *
> * Return: 0 if successful, error code otherwise.
> */
> static int ov9282_update_controls(struct ov9282 *ov9282,
> - const struct ov9282_mode *mode)
> + const struct ov9282_mode *mode,
> + const struct v4l2_subdev_format *fmt)
> {
> u32 hblank_min;
> + s64 pixel_rate;
> int ret;
>
> ret = __v4l2_ctrl_s_ctrl(ov9282->link_freq_ctrl, mode->link_freq_idx);
> if (ret)
> return ret;
>
> - hblank_min = mode->hblank_min[ov9282->noncontinuous_clock ? 0 : 1];
> - ret = __v4l2_ctrl_modify_range(ov9282->hblank_ctrl, hblank_min,
> - OV9282_TIMING_HTS_MAX - mode->width, 1,
> - hblank_min);
> + pixel_rate = (fmt->format.code == MEDIA_BUS_FMT_Y10_1X10) ?
> + OV9282_PIXEL_RATE_10BIT : OV9282_PIXEL_RATE_8BIT;
> + ret = __v4l2_ctrl_modify_range(ov9282->pixel_rate, pixel_rate,
> + pixel_rate, 1, pixel_rate);
> + if (ret)
> + return ret;
> +
> + if (ov9282->cur_mode != mode) {
Why has this become conditional in this patch, and why only for hblank ?
> + hblank_min = mode->hblank_min[ov9282->noncontinuous_clock ? 0 : 1];
> + ret = __v4l2_ctrl_modify_range(ov9282->hblank_ctrl, hblank_min,
> + OV9282_TIMING_HTS_MAX - mode->width, 1,
> + hblank_min);
> + if (ret)
> + return ret;
> +
> + ret = __v4l2_ctrl_s_ctrl(ov9282->hblank_ctrl, hblank_min);
> + if (ret)
> + return ret;
> + }
>
> return __v4l2_ctrl_modify_range(ov9282->vblank_ctrl, mode->vblank_min,
> mode->vblank_max, 1, mode->vblank);
> @@ -693,10 +723,16 @@ static int ov9282_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *sd_state,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - if (code->index > 0)
> + switch (code->index) {
> + default:
> return -EINVAL;
Can default: come after the valid cases ?
> -
> - code->code = MEDIA_BUS_FMT_Y10_1X10;
> + case 0:
> + code->code = MEDIA_BUS_FMT_Y10_1X10;
> + break;
> + case 1:
> + code->code = MEDIA_BUS_FMT_Y8_1X8;
> + break;
> + }
>
> return 0;
> }
> @@ -716,7 +752,8 @@ static int ov9282_enum_frame_size(struct v4l2_subdev *sd,
> if (fsize->index >= OV9282_NUM_MODES)
> return -EINVAL;
>
> - if (fsize->code != MEDIA_BUS_FMT_Y10_1X10)
> + if (fsize->code != MEDIA_BUS_FMT_Y10_1X10 &&
> + fsize->code != MEDIA_BUS_FMT_Y8_1X8)
> return -EINVAL;
>
> fsize->min_width = supported_modes[fsize->index].width;
> @@ -732,15 +769,17 @@ static int ov9282_enum_frame_size(struct v4l2_subdev *sd,
> * from selected sensor mode
> * @ov9282: pointer to ov9282 device
> * @mode: pointer to ov9282_mode sensor mode
> + * @code: mbus code to be stored
> * @fmt: V4L2 sub-device format need to be filled
> */
> static void ov9282_fill_pad_format(struct ov9282 *ov9282,
> const struct ov9282_mode *mode,
> + u32 code,
> struct v4l2_subdev_format *fmt)
> {
> fmt->format.width = mode->width;
> fmt->format.height = mode->height;
> - fmt->format.code = MEDIA_BUS_FMT_Y10_1X10;
> + fmt->format.code = code;
> fmt->format.field = V4L2_FIELD_NONE;
> fmt->format.colorspace = V4L2_COLORSPACE_RAW;
> fmt->format.ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
> @@ -770,7 +809,8 @@ static int ov9282_get_pad_format(struct v4l2_subdev *sd,
> framefmt = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> fmt->format = *framefmt;
> } else {
> - ov9282_fill_pad_format(ov9282, ov9282->cur_mode, fmt);
> + ov9282_fill_pad_format(ov9282, ov9282->cur_mode, ov9282->code,
> + fmt);
> }
>
> mutex_unlock(&ov9282->mutex);
> @@ -792,6 +832,7 @@ static int ov9282_set_pad_format(struct v4l2_subdev *sd,
> {
> struct ov9282 *ov9282 = to_ov9282(sd);
> const struct ov9282_mode *mode;
> + u32 code;
> int ret = 0;
>
> mutex_lock(&ov9282->mutex);
> @@ -801,7 +842,12 @@ static int ov9282_set_pad_format(struct v4l2_subdev *sd,
> width, height,
> fmt->format.width,
> fmt->format.height);
> - ov9282_fill_pad_format(ov9282, mode, fmt);
> + if (fmt->format.code == MEDIA_BUS_FMT_Y8_1X8)
> + code = MEDIA_BUS_FMT_Y8_1X8;
> + else
> + code = MEDIA_BUS_FMT_Y10_1X10;
> +
> + ov9282_fill_pad_format(ov9282, mode, code, fmt);
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> struct v4l2_mbus_framefmt *framefmt;
> @@ -809,9 +855,11 @@ static int ov9282_set_pad_format(struct v4l2_subdev *sd,
> framefmt = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> *framefmt = fmt->format;
> } else {
> - ret = ov9282_update_controls(ov9282, mode);
> - if (!ret)
> + ret = ov9282_update_controls(ov9282, mode, fmt);
> + if (!ret) {
> ov9282->cur_mode = mode;
> + ov9282->code = code;
> + }
> }
>
> mutex_unlock(&ov9282->mutex);
> @@ -833,7 +881,7 @@ static int ov9282_init_pad_cfg(struct v4l2_subdev *sd,
> struct v4l2_subdev_format fmt = { 0 };
>
> fmt.which = sd_state ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> - ov9282_fill_pad_format(ov9282, &supported_modes[0], &fmt);
> + ov9282_fill_pad_format(ov9282, &supported_modes[0], ov9282->code, &fmt);
>
> return ov9282_set_pad_format(sd, sd_state, &fmt);
> }
> @@ -898,7 +946,17 @@ static int ov9282_get_selection(struct v4l2_subdev *sd,
> */
> static int ov9282_start_streaming(struct ov9282 *ov9282)
> {
> + const struct ov9282_reg bitdepth_regs[2][2] = {
> + {
> + {OV9282_REG_PLL_CTRL_0D, OV9282_PLL_CTRL_0D_RAW10},
> + {OV9282_REG_ANA_CORE_2, OV9282_ANA_CORE2_RAW10},
> + }, {
> + {OV9282_REG_PLL_CTRL_0D, OV9282_PLL_CTRL_0D_RAW8},
> + {OV9282_REG_ANA_CORE_2, OV9282_ANA_CORE2_RAW8},
> + }
> + };
> const struct ov9282_reg_list *reg_list;
> + int bitdepth_index;
> int ret;
>
> /* Write common registers */
> @@ -917,6 +975,13 @@ static int ov9282_start_streaming(struct ov9282 *ov9282)
> return ret;
> }
>
> + bitdepth_index = ov9282->code == MEDIA_BUS_FMT_Y10_1X10 ? 0 : 1;
> + ret = ov9282_write_regs(ov9282, bitdepth_regs[bitdepth_index], 2);
> + if (ret) {
> + dev_err(ov9282->dev, "fail to write bitdepth regs");
> + return ret;
> + }
> +
> /* Write sensor mode registers */
> reg_list = &ov9282->cur_mode->reg_list;
> ret = ov9282_write_regs(ov9282, reg_list->regs, reg_list->num_of_regs);
> @@ -1258,9 +1323,11 @@ static int ov9282_init_controls(struct ov9282 *ov9282)
> 0, 1, 1, 1);
>
> /* Read only controls */
> - v4l2_ctrl_new_std(ctrl_hdlr, &ov9282_ctrl_ops, V4L2_CID_PIXEL_RATE,
> - OV9282_PIXEL_RATE, OV9282_PIXEL_RATE, 1,
> - OV9282_PIXEL_RATE);
> + ov9282->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &ov9282_ctrl_ops,
> + V4L2_CID_PIXEL_RATE,
> + OV9282_PIXEL_RATE_10BIT,
> + OV9282_PIXEL_RATE_10BIT, 1,
> + OV9282_PIXEL_RATE_10BIT);
>
> ov9282->link_freq_ctrl = v4l2_ctrl_new_int_menu(ctrl_hdlr,
> &ov9282_ctrl_ops,
> @@ -1342,6 +1409,7 @@ static int ov9282_probe(struct i2c_client *client)
>
> /* Set default mode to first mode */
> ov9282->cur_mode = &supported_modes[0];
> + ov9282->code = MEDIA_BUS_FMT_Y10_1X10;
> ov9282->vblank = ov9282->cur_mode->vblank;
>
> ret = ov9282_init_controls(ov9282);
> --
> 2.34.1
>
