Thanks, Hans, for your comments.
I will take care of all comments regarding this change in next patch.
Will also send a patch to update the documentation.
Venus driver already has support for S_PARM for decoder, will add support for G_PARM as well and send a patch.
Thanks,
Dikshita
-----Original Message-----
From: Hans Verkuil <hverkuil-cisco@xxxxxxxxx>
Sent: Friday, September 9, 2022 5:47 PM
To: Dikshita Agarwal (QUIC) <quic_dikshita@xxxxxxxxxxx>; linux-media@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
Cc: stanimir.varbanov@xxxxxxxxxx; Vikash Garodia (QUIC) <quic_vgarodia@xxxxxxxxxxx>; Maheshwar Ajja (QUIC) <quic_majja@xxxxxxxxxxx>; quic_jdas <quic_jdas@xxxxxxxxxxx>
Subject: Re: [PATCH] Allow S/G_PARM for stateful decoder
Hi Dikshita,
First I'll comment on this patch, then at the end I have more high-level comments.
On 29/08/2022 09:54, Dikshita Agarwal wrote:
> Some stateful decoder supports S/G_PARM similar to a
decoder -> decoders
BTW, which decoder drivers support this in mainline? Or is this for out-of-tree drivers?
> stateful encoder. S_PARM(OUTPUT) reserves hardware decoder resources,
> and G_PARM(CAPTURE) returns the embedded frame interval. Allow the
> same with this change.
>
> Signed-off-by: Dikshita Agarwal <quic_dikshita@xxxxxxxxxxx>
> ---
> utils/v4l2-compliance/v4l2-test-formats.cpp | 4 ----
> 1 file changed, 4 deletions(-)
>
> diff --git a/utils/v4l2-compliance/v4l2-test-formats.cpp
> b/utils/v4l2-compliance/v4l2-test-formats.cpp
> index 269a383..e996558 100644
> --- a/utils/v4l2-compliance/v4l2-test-formats.cpp
> +++ b/utils/v4l2-compliance/v4l2-test-formats.cpp
> @@ -64,8 +64,6 @@ static int testEnumFrameIntervals(struct node *node, __u32 pixfmt,
> ret = doioctl(node, VIDIOC_ENUM_FRAMEINTERVALS, &frmival);
> if (ret == ENOTTY)
> return ret;
> - // M2M devices don't support this, except for stateful encoders
> - fail_on_test(node->is_m2m && !(node->codec_mask & STATEFUL_ENCODER));
M2M devices still don't support this, except for stateful codecs. So this test should still be there, just changed to:
!(node->codec_mask & (STATEFUL_ENCODER | STATEFUL_DECODER))
> if (f == 0 && ret == EINVAL) {
> if (type == V4L2_FRMSIZE_TYPE_DISCRETE)
> warn("found framesize %dx%d, but no frame intervals\n", w, h); @@
> -1367,8 +1365,6 @@ static int testParmType(struct node *node, unsigned type)
> }
> if (ret == ENOTTY)
> return ret;
> - // M2M devices don't support this, except for stateful encoders
> - fail_on_test(node->is_m2m && !is_stateful_enc);
Similar.
> if (ret == EINVAL)
> return ENOTTY;
> if (ret)
But modifying the utility is something you only do if the spec has first been updated.
So the stateful decoder chapter needs to be modified so it explains how G/S_PARM shall be used. And ideally have at least one driver that supports it.
Regards,
Hans
