Configure the rear camera found in the 8MP camera module for
Fairphone 2. There's also a AD5823 autofocus coil and an EEPROM present
on the module but currently not included.
Signed-off-by: Luca Weiss <luca@xxxxxxxxx>
---
.../dts/qcom-msm8974pro-fairphone-fp2.dts | 70 +++++++++++++++++++
1 file changed, 70 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
index 0fad82fc9e03..9a2c3a9177de 100644
--- a/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
@@ -77,6 +77,60 @@ &blsp1_uart2 {
status = "okay";
};
+&camss {
+ status = "okay";
+
+ vdda-supply = <&pm8941_l12>;
+
+ ports {
+ port@0 {
+ reg = <0>;
+ csiphy0_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2 3 4>;
+ link-frequencies = /bits/ 64 <360000000>;
+ remote-endpoint = <&ov8865_ep>;
+ };
+ };
+ };
+};
+
+&cci {
+ status = "okay";
+};
+
+&cci_i2c0 {
+ ov8865: camera-sensor@10 {
+ compatible = "ovti,ov8865";
+ reg = <0x10>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mclk0_pin_a>;
+
+ clocks = <&mmcc CAMSS_MCLK0_CLK>;
+
+ avdd-supply = <&pm8941_l17>;
+ dovdd-supply = <&pm8941_lvs3>;
+ dvdd-supply = <&pm8941_l3>;
+
+ powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&tlmm 90 GPIO_ACTIVE_LOW>;
+
+ /* Rear camera */
+ orientation = <1>;
+ rotation = <90>;
+
+ port {
+ ov8865_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2 3 4>;
+ link-frequencies = /bits/ 64 <360000000>;
+ remote-endpoint = <&csiphy0_ep>;
+ };
+ };
+ };
+};
+
&dsi0 {
status = "okay";
@@ -413,6 +467,15 @@ pm8941_l24: l24 {
regulator-max-microvolt = <3075000>;
regulator-boot-on;
};
+
+ pm8941_lvs3: lvs3 {
+ /*
+ * TODO: Used as CCI0 and CCI1 pull-up.
+ * Replace with vbus-supply or similar once this lands
+ * upstream!
+ */
+ regulator-always-on;
+ };
};
};
@@ -449,6 +512,13 @@ &smbb {
};
&tlmm {
+ mclk0_pin_a: mclk0-pin-active {
+ pins = "gpio15";
+ function = "cam_mclk0";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
panel_pin: panel {
te {
pins = "gpio12";
--
2.36.0
