Hi Adam On Tue, 12 Apr 2022 at 14:55, Adam Ford <aford173@xxxxxxxxx> wrote: > > In the table of modes, each mode sets the DPHY to auto. > Create a helper function which does the same thing while > removing the entry for auto DPHY from ever mode entry. s/ever/every > > Signed-off-by: Adam Ford <aford173@xxxxxxxxx> > --- > drivers/media/i2c/imx219.c | 24 ++++++++++++++++++++---- > 1 file changed, 20 insertions(+), 4 deletions(-) > > diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c > index 08e7d0e72430..bb0bc1b8d91c 100644 > --- a/drivers/media/i2c/imx219.c > +++ b/drivers/media/i2c/imx219.c > @@ -35,6 +35,10 @@ > #define IMX219_MODE_STANDBY 0x00 > #define IMX219_MODE_STREAMING 0x01 > > + > +#define IMX219_REG_DPHY_CTRL 0x0128 > +#define IMX219_DPHY_AUTO 0 > + > /* Chip ID */ > #define IMX219_REG_CHIP_ID 0x0000 > #define IMX219_CHIP_ID 0x0219 > @@ -183,7 +187,6 @@ static const struct imx219_reg pll_clk_table[] = { > * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7. > */ > static const struct imx219_reg mode_3280x2464_regs[] = { > - {0x0128, 0x00}, > {0x012b, 0x00}, > {0x0164, 0x00}, > {0x0165, 0x00}, > @@ -222,7 +225,6 @@ static const struct imx219_reg mode_3280x2464_regs[] = { > }; > > static const struct imx219_reg mode_1920_1080_regs[] = { > - {0x0128, 0x00}, > {0x012b, 0x00}, > {0x0162, 0x0d}, > {0x0163, 0x78}, > @@ -261,7 +263,6 @@ static const struct imx219_reg mode_1920_1080_regs[] = { > }; > > static const struct imx219_reg mode_1640_1232_regs[] = { > - {0x0128, 0x00}, > {0x012b, 0x00}, > {0x0164, 0x00}, > {0x0165, 0x00}, > @@ -300,7 +301,6 @@ static const struct imx219_reg mode_1640_1232_regs[] = { > }; > > static const struct imx219_reg mode_640_480_regs[] = { > - {0x0128, 0x00}, > {0x012b, 0x00}, > {0x0162, 0x0d}, > {0x0163, 0x78}, > @@ -999,6 +999,15 @@ static int imx219_get_selection(struct v4l2_subdev *sd, > return -EINVAL; > } > > +static int imx219_enable_dphy(struct imx219 *imx219, u8 mode) > +{ > + int ret; > + > + ret = imx219_write_reg(imx219, IMX219_REG_DPHY_CTRL, > + IMX219_REG_VALUE_08BIT, mode); Is there a specific reason to extract this one register, but leave the block {0x455e, 0x00}, {0x471e, 0x4b}, {0x4767, 0x0f}, {0x4750, 0x14}, {0x4540, 0x00}, {0x47b4, 0x14}, {0x4713, 0x30}, {0x478b, 0x10}, {0x478f, 0x10}, {0x4793, 0x10}, {0x4797, 0x0e}, {0x479b, 0x0e}, {0x0162, 0x0d}, {0x0163, 0x78}, that appear to also be common to all modes. Other drivers break that lot out into a global registers array that is always sent, rather than individual register writes. Having this one register extra write as a new function is actually likely to increase the size of the module overall, instead of reducing it. Dave > + return ret; > +}; > + > static int imx219_configure_lanes(struct imx219 *imx219) > { > int ret; > @@ -1081,6 +1090,13 @@ static int imx219_start_streaming(struct imx219 *imx219) > goto err_rpm_put; > } > > + /* Setup DPHY */ > + ret = imx219_enable_dphy(imx219, IMX219_DPHY_AUTO); > + if (ret) { > + dev_err(&client->dev, "%s failed to configure dphy\n", __func__); > + goto err_rpm_put; > + } > + > /* Configure clock based on reference clock frequency */ > imx219_set_exck_freq(imx219); > > -- > 2.34.1 >