[PATCH 3/4] media: i2c: imx219: Enable variable XCLK

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The datasheet shows the external clock can be anything
from 6MHz to 27MHz, but EXCK, PREPLLCK_VT_DIV and
PREPLLCK_OP_DIV need to change based on the clock, so
create helper functions to set these registers based on
the rate of xclk.

Move the validation of the clock rate into imx219_check_hwcfg
which means delaying the call to it until after xclk has been
determined.

Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
---
 drivers/media/i2c/imx219.c | 79 ++++++++++++++++++++++++++++++--------
 1 file changed, 63 insertions(+), 16 deletions(-)

diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index d13ce5c1ece6..08e7d0e72430 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -39,8 +39,12 @@
 #define IMX219_REG_CHIP_ID		0x0000
 #define IMX219_CHIP_ID			0x0219
 
-/* External clock frequency is 24.0M */
-#define IMX219_XCLK_FREQ		24000000
+/* Default external clock frequency is 24.0M */
+#define IMX219_XCLK_MIN_FREQ		6000000
+#define IMX219_XCLK_MAX_FREQ		27000000
+#define IMX219_REG_EXCK			0x012a
+#define IMX219_REG_PREPLLCK_VT_DIV	0x0304
+#define IMX219_REG_PREPLLCK_OP_DIV	0x0305
 
 /* Pixel rate is fixed for all the modes */
 #define IMX219_PIXEL_RATE		182400000
@@ -166,8 +170,6 @@ static const struct imx219_reg pll_clk_table[] = {
 
 	{0x0301, 0x05},	/* VTPXCK_DIV */
 	{0x0303, 0x01},	/* VTSYSCK_DIV */
-	{0x0304, 0x03},	/* PREPLLCK_VT_DIV 0x03 = AUTO set */
-	{0x0305, 0x03}, /* PREPLLCK_OP_DIV 0x03 = AUTO set */
 	{0x0306, 0x00},	/* PLL_VT_MPY */
 	{0x0307, 0x39},
 	{0x030b, 0x01},	/* OP_SYS_CLK_DIV */
@@ -182,7 +184,6 @@ static const struct imx219_reg pll_clk_table[] = {
  */
 static const struct imx219_reg mode_3280x2464_regs[] = {
 	{0x0128, 0x00},
-	{0x012a, 0x18},
 	{0x012b, 0x00},
 	{0x0164, 0x00},
 	{0x0165, 0x00},
@@ -222,7 +223,6 @@ static const struct imx219_reg mode_3280x2464_regs[] = {
 
 static const struct imx219_reg mode_1920_1080_regs[] = {
 	{0x0128, 0x00},
-	{0x012a, 0x18},
 	{0x012b, 0x00},
 	{0x0162, 0x0d},
 	{0x0163, 0x78},
@@ -262,7 +262,6 @@ static const struct imx219_reg mode_1920_1080_regs[] = {
 
 static const struct imx219_reg mode_1640_1232_regs[] = {
 	{0x0128, 0x00},
-	{0x012a, 0x18},
 	{0x012b, 0x00},
 	{0x0164, 0x00},
 	{0x0165, 0x00},
@@ -302,7 +301,6 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
 
 static const struct imx219_reg mode_640_480_regs[] = {
 	{0x0128, 0x00},
-	{0x012a, 0x18},
 	{0x012b, 0x00},
 	{0x0162, 0x0d},
 	{0x0163, 0x78},
@@ -1015,6 +1013,50 @@ static int imx219_configure_lanes(struct imx219 *imx219)
 	return ret;
 };
 
+static int imx219_set_exck_freq(struct imx219 *imx219)
+{
+	int ret;
+	/* The imx219 registers need MHz not Hz */
+	u8 clk = (u8) (imx219->xclk_freq/1000000U);
+
+	/* Set the clock frequency in MHz */
+	ret = imx219_write_reg(imx219, IMX219_REG_EXCK,
+			       IMX219_REG_VALUE_08BIT, clk);
+
+	/* Configure the PREPLLCK_VT_DIV and PREPLLCK_OP_DIV for automatic */
+	switch (clk) {
+	case 6 ... 11:
+		ret = imx219_write_reg(imx219, IMX219_REG_PREPLLCK_VT_DIV,
+			       IMX219_REG_VALUE_08BIT, 0x01);
+		if (ret)
+			return ret;
+		ret = imx219_write_reg(imx219, IMX219_REG_PREPLLCK_OP_DIV,
+			       IMX219_REG_VALUE_08BIT, 0x01);
+		return ret;
+	case 12 ... 23:
+		ret = imx219_write_reg(imx219, IMX219_REG_PREPLLCK_VT_DIV,
+			       IMX219_REG_VALUE_08BIT, 0x02);
+		if (ret)
+			return ret;
+
+		ret = imx219_write_reg(imx219, IMX219_REG_PREPLLCK_OP_DIV,
+			       IMX219_REG_VALUE_08BIT, 0x02);
+
+		return ret;
+	case 24 ... 27:
+		ret = imx219_write_reg(imx219, IMX219_REG_PREPLLCK_VT_DIV,
+			       IMX219_REG_VALUE_08BIT, 0x03);
+		if (ret)
+			return ret;
+		ret = imx219_write_reg(imx219, IMX219_REG_PREPLLCK_OP_DIV,
+			       IMX219_REG_VALUE_08BIT, 0x03);
+		return ret;
+	default:
+		/* Should never get here */
+		return -EINVAL;
+	}
+}
+
 static int imx219_start_streaming(struct imx219 *imx219)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
@@ -1039,6 +1081,9 @@ static int imx219_start_streaming(struct imx219 *imx219)
 		goto err_rpm_put;
 	}
 
+	/* Configure clock based on reference clock frequency */
+	imx219_set_exck_freq(imx219);
+
 	/* Apply default values of current mode */
 	reg_list = &imx219->mode->reg_list;
 	ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
@@ -1428,6 +1473,13 @@ static int imx219_check_hwcfg(struct imx219 *imx219)
 		return -EINVAL;
 	}
 
+	if ((imx219->xclk_freq < IMX219_XCLK_MIN_FREQ) ||
+	     imx219->xclk_freq > IMX219_XCLK_MAX_FREQ) {
+		dev_err(&client->dev, "xclk frequency not supported: %d Hz\n",
+			imx219->xclk_freq);
+		return -EINVAL;
+	}
+
 	return 0;
 }
 
@@ -1478,10 +1530,6 @@ static int imx219_probe(struct i2c_client *client)
 	if (ret)
 		return ret;
 
-	/* Check the hardware configuration in device tree */
-	if (imx219_check_hwcfg(imx219))
-		return -EINVAL;
-
 	/* Get system clock (xclk) */
 	imx219->xclk = devm_clk_get(dev, NULL);
 	if (IS_ERR(imx219->xclk)) {
@@ -1490,11 +1538,10 @@ static int imx219_probe(struct i2c_client *client)
 	}
 
 	imx219->xclk_freq = clk_get_rate(imx219->xclk);
-	if (imx219->xclk_freq != IMX219_XCLK_FREQ) {
-		dev_err(dev, "xclk frequency not supported: %d Hz\n",
-			imx219->xclk_freq);
+
+	/* Check the hardware configuration in device tree */
+	if (imx219_check_hwcfg(imx219))
 		return -EINVAL;
-	}
 
 	ret = imx219_get_regulators(imx219);
 	if (ret) {
-- 
2.34.1




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux