Hi Sakari,
On Thu, Mar 3, 2022 at 5:09 PM Sakari Ailus
<sakari.ailus@xxxxxxxxxxxxxxx> wrote:
>
> Hi Kate,
>
> Thank you for the patch.
>
> On Wed, Feb 23, 2022 at 05:06:48PM +0800, Kate Hsuan wrote:
> > For the AF configuration, if the rightmost stripe is used, the AF scene
> > will be at the incorrect location of the sensor.
> >
> > The AF coordinate may be set to the right part of the sensor. This
> > configuration would lead to x_start being greater than the
> > down_scaled_stripes offset and the leftmost stripe would be disabled
> > and only the rightmost stripe is used to control the AF coordinate. If
> > the x_start doesn't perform any adjustments, the AF coordinate will be
> > at the wrong place of the sensor since down_scaled_stripes offset
> > would be the new zero of the coordinate system.
> >
> > In this patch, if only the rightmost stripe is used, x_start should
> > minus down_scaled_stripes offset to maintain its correctness of AF
> > scene coordinate.
> >
> > Signed-off-by: Kate Hsuan <hpa@xxxxxxxxxx>
> > ---
> > drivers/staging/media/ipu3/ipu3-css-params.c | 9 ++++++++-
> > 1 file changed, 8 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/staging/media/ipu3/ipu3-css-params.c b/drivers/staging/media/ipu3/ipu3-css-params.c
> > index d9e3c3785075..efe4de8ef205 100644
> > --- a/drivers/staging/media/ipu3/ipu3-css-params.c
> > +++ b/drivers/staging/media/ipu3/ipu3-css-params.c
> > @@ -2556,6 +2556,14 @@ int imgu_css_cfg_acc(struct imgu_css *css, unsigned int pipe,
> > /* Enable only for rightmost stripe, disable left */
> > acc->af.stripes[0].grid_cfg.y_start &=
> > ~IPU3_UAPI_GRID_Y_START_EN;
> > + acc->af.stripes[0].grid_cfg.x_start -=
> > + acc->stripe.down_scaled_stripes[1].offset;
> > + acc->af.stripes[0].grid_cfg.x_end -=
> > + acc->stripe.down_scaled_stripes[1].offset;
> > + acc->af.stripes[1].grid_cfg.x_start -=
> > + acc->stripe.down_scaled_stripes[1].offset;
> > + acc->af.stripes[1].grid_cfg.x_end -=
> > + acc->stripe.down_scaled_stripes[1].offset;
>
> The grid x/y ends are calculated from the width when both grids are enabled
> and I think it should work the same way here. There's also masking of the
> bits that aren't in use.
Thanks for clarifying this :)
>
> The first stripe isn't enabled so changing values there has no effect as
> far as I can tell.
>
Okay. I would remove the setting of the first stripe in the v2 patch.
Thank you
> Looking at the code a little, it seems all awb_fr, ae and af seem to suffer
> from the same issue. Let's still iron out the fix for af first before
> considering those.
>
> > } else if (acc->af.config.grid_cfg.x_end <=
> > acc->stripe.bds_out_stripes[0].width - min_overlap) {
> > /* Enable only for leftmost stripe, disable right */
> > @@ -2563,7 +2571,6 @@ int imgu_css_cfg_acc(struct imgu_css *css, unsigned int pipe,
> > ~IPU3_UAPI_GRID_Y_START_EN;
> > } else {
> > /* Enable for both stripes */
> > -
> > acc->af.stripes[0].grid_cfg.width =
> > (acc->stripe.bds_out_stripes[0].width - min_overlap -
> > acc->af.config.grid_cfg.x_start + 1) >>
>
> --
> Kind regards,
>
> Sakari Ailus
>
--
BR,
Kate
