Hi Jean-Michel,
Thank you for the patch.
On Fri, Jan 21, 2022 at 09:18:10AM +0100, Jean-Michel Hautbois wrote:
> Configure the csi1 endpoint, add the imx219 node and connect it through
> the i2c mux.
This is not meant to be upstreamed, is it ? Please say so very loudly in
the commit message.
> Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@xxxxxxxxxxxxxxxx>
> ---
> MAINTAINERS | 1 +
> arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 1 +
> arch/arm/boot/dts/bcm283x-rpi-imx219.dtsi | 102 ++++++++++++++++++++++
> 3 files changed, 104 insertions(+)
> create mode 100644 arch/arm/boot/dts/bcm283x-rpi-imx219.dtsi
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index b17bb533e007..56544ac98d69 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -3684,6 +3684,7 @@ M: Raspberry Pi Kernel Maintenance <kernel-list@xxxxxxxxxxxxxxx>
> L: linux-media@xxxxxxxxxxxxxxx
> S: Maintained
> F: Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
> +F: arch/arm/boot/dts/bcm283x*
> F: drivers/media/platform/bcm2835/
>
> BROADCOM BCM47XX MIPS ARCHITECTURE
> diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> index 4432412044de..f7625b70fe57 100644
> --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
> @@ -4,6 +4,7 @@
> #include "bcm2711-rpi.dtsi"
> #include "bcm283x-rpi-usb-peripheral.dtsi"
> #include "bcm283x-rpi-wifi-bt.dtsi"
> +#include "bcm283x-rpi-imx219.dtsi"
Let's use an overlay instead.
>
> / {
> compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
> diff --git a/arch/arm/boot/dts/bcm283x-rpi-imx219.dtsi b/arch/arm/boot/dts/bcm283x-rpi-imx219.dtsi
> new file mode 100644
> index 000000000000..f2c6a85fd731
> --- /dev/null
> +++ b/arch/arm/boot/dts/bcm283x-rpi-imx219.dtsi
> @@ -0,0 +1,102 @@
> +// SPDX-License-Identifier: GPL-2.0
> +#include <dt-bindings/clock/bcm2835.h>
> +
> +/ {
> + compatible = "brcm,bcm2835";
> +
> + imx219_vdig: fixedregulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "imx219_vdig";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + imx219_vddl: fixedregulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "imx219_vddl";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + };
> +
> + imx219_clk: imx219_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "24MHz-clock";
> + };
> +
> + cam1_reg: cam1_reg {
> + compatible = "regulator-fixed";
> + regulator-name = "imx219_vana";
> + enable-active-high;
> + status = "okay";
> + gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>;
> + };
This regulator belongs to the board dtsi. Same for the I2C mux below
(but not the imx219 of course).
> +
> + i2c0mux {
> + compatible = "i2c-mux-pinctrl";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c-parent = <&i2c0>;
> +
> + pinctrl-names = "i2c0", "i2c_csi_dsi";
> + pinctrl-0 = <&i2c0_gpio0>;
> + pinctrl-1 = <&i2c0_gpio44>;
> +
> + i2c@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + imx219: sensor@10 {
> + compatible = "sony,imx219";
> + reg = <0x10>;
> + status = "okay";
> +
> + clocks = <&imx219_clk>;
> + clock-names = "xclk";
> +
> + VANA-supply = <&cam1_reg>; /* 2.8v */
> + VDIG-supply = <&imx219_vdig>; /* 1.8v */
> + VDDL-supply = <&imx219_vddl>; /* 1.2v */
> +
> + rotation = <0>;
> + orientation = <0>;
> +
> + port {
> + imx219_0: endpoint {
> + remote-endpoint = <&csi1_ep>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + clock-noncontinuous;
> + link-frequencies = /bits/ 64 <456000000>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&csi1 {
> + status="okay";
> + num-data-lanes = <2>;
> + port {
> + csi1_ep: endpoint {
> + remote-endpoint = <&imx219_0>;
> + data-lanes = <1 2>;
> + clock-lanes = <0>;
> + };
> + };
> +};
> +
> +&i2c0 {
> + /delete-property/ pinctrl-names;
> + /delete-property/ pinctrl-0;
> +};
> +
--
Regards,
Laurent Pinchart
