This is meant to select a platform-dependent factor between Linux and Windows. It makes no sense to keep it on Kernel. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx> --- To avoid mailbombing on a large number of people, only mailing lists were C/C on the cover. See [PATCH 00/13] at: https://lore.kernel.org/all/cover.1637140900.git.mchehab+huawei@xxxxxxxxxx/ .../media/atomisp/pci/ia_css_stream_public.h | 10 ++++----- .../media/atomisp/pci/sh_css_param_shading.c | 22 ------------------- 2 files changed, 4 insertions(+), 28 deletions(-) diff --git a/drivers/staging/media/atomisp/pci/ia_css_stream_public.h b/drivers/staging/media/atomisp/pci/ia_css_stream_public.h index 649f22b03de8..47846ece8d64 100644 --- a/drivers/staging/media/atomisp/pci/ia_css_stream_public.h +++ b/drivers/staging/media/atomisp/pci/ia_css_stream_public.h @@ -102,12 +102,10 @@ struct ia_css_stream_config { isys_config[IA_CSS_STREAM_MAX_ISYS_STREAM_PER_CH]; struct ia_css_stream_input_config input_config; - /* Currently, Android and Windows platforms interpret the binning_factor parameter - * differently. In Android, the binning factor is expressed in the form - * 2^N * 2^N, whereas in Windows platform, the binning factor is N*N - * To use the Windows method of specification, the caller has to define - * macro USE_WINDOWS_BINNING_FACTOR. This is for backward compatibility only - * and will be deprecated. In the future,all platforms will use the N*N method + /* + * Currently, Linux and Windows platforms interpret the binning_factor + * parameter differently. In Linux, the binning factor is expressed + * in the form 2^N * 2^N */ /* ISP2401 */ unsigned int sensor_binning_factor; /** Binning factor used by sensor diff --git a/drivers/staging/media/atomisp/pci/sh_css_param_shading.c b/drivers/staging/media/atomisp/pci/sh_css_param_shading.c index 69cc4e423d8b..51d83ce0d9cb 100644 --- a/drivers/staging/media/atomisp/pci/sh_css_param_shading.c +++ b/drivers/staging/media/atomisp/pci/sh_css_param_shading.c @@ -271,33 +271,11 @@ prepare_shading_table(const struct ia_css_shading_table *in_table, bds_denominator - binary->info->sp.pipeline.top_cropping; -#if !defined(USE_WINDOWS_BINNING_FACTOR) - /* @deprecated{This part of the code will be replaced by the code - * in the #else section below to make the calculation same across - * all platforms. - * Android and Windows platforms interpret the binning_factor parameter - * differently. In Android, the binning factor is expressed in the form - * 2^N * 2^N, whereas in Windows platform, the binning factor is N*N} - */ - - /* We take into account the binning done by the sensor. We do this - by cropping the non-binned part of the shading table and then - increasing the size of a grid cell with this same binning factor. */ - input_width <<= sensor_binning; - input_height <<= sensor_binning; - /* We also scale the padding by the same binning factor. This will - make it much easier later on to calculate the padding of the - shading table. */ - left_padding <<= sensor_binning; - right_padding <<= sensor_binning; - top_padding <<= sensor_binning; -#else input_width *= sensor_binning; input_height *= sensor_binning; left_padding *= sensor_binning; right_padding *= sensor_binning; top_padding *= sensor_binning; -#endif /*USE_WINDOWS_BINNING_FACTOR*/ /* during simulation, the used resolution can exceed the sensor resolution, so we clip it. */ -- 2.33.1
