On Wed, Aug 18, 2021 at 07:29:09PM +0300, Sakari Ailus wrote: > Hi Krzysztof, > > Thanks for the patch. > > On Fri, Jul 30, 2021 at 09:41:23AM +0200, Krzysztof Hałasa wrote: > > The driver has been extensively tested in an i.MX6-based system. > > > > Signed-off-by: Krzysztof Hałasa <khalasa@xxxxxxx> > > --- > > No changes from v3 here. > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > index a61f4f3b78a9..f92b56487fc6 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -1331,6 +1331,12 @@ S: Supported > > W: http://www.aquantia.com > > F: drivers/net/ethernet/aquantia/atlantic/aq_ptp* > > > > +AR0521 ON SEMICONDUCTOR CAMERA SENSOR DRIVER > > +M: Krzysztof Hałasa <khalasa@xxxxxxx> > > +L: linux-media@xxxxxxxxxxxxxxx > > +S: Maintained > > +F: drivers/media/i2c/ar0521.c > > + > > ARASAN NAND CONTROLLER DRIVER > > M: Miquel Raynal <miquel.raynal@xxxxxxxxxxx> > > M: Naga Sureshkumar Relli <nagasure@xxxxxxxxxx> > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > > index 588f8eb95984..0c41a3c18671 100644 > > --- a/drivers/media/i2c/Kconfig > > +++ b/drivers/media/i2c/Kconfig > > @@ -729,6 +729,16 @@ config VIDEO_APTINA_PLL > > config VIDEO_CCS_PLL > > tristate > > > > +config VIDEO_AR0521 > > + tristate "ON Semiconductor AR0521 sensor support" > > + depends on I2C && VIDEO_V4L2 > > + help > > + This is a Video4Linux2 sensor driver for the ON Semiconductor > > + AR0521 camera. > > + > > + To compile this driver as a module, choose M here: the > > + module will be called ar0521. > > + > > config VIDEO_HI556 > > tristate "Hynix Hi-556 sensor support" > > depends on I2C && VIDEO_V4L2 > > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > > index 1168fa6b84ed..3351deeb741b 100644 > > --- a/drivers/media/i2c/Makefile > > +++ b/drivers/media/i2c/Makefile > > @@ -8,6 +8,7 @@ obj-$(CONFIG_VIDEO_CX25840) += cx25840/ > > obj-$(CONFIG_VIDEO_M5MOLS) += m5mols/ > > > > obj-$(CONFIG_VIDEO_APTINA_PLL) += aptina-pll.o > > +obj-$(CONFIG_VIDEO_AR0521) += ar0521.o > > Could you arrange this next to other sensors? > > > obj-$(CONFIG_VIDEO_TVAUDIO) += tvaudio.o > > obj-$(CONFIG_VIDEO_TDA7432) += tda7432.o > > obj-$(CONFIG_VIDEO_SAA6588) += saa6588.o > > diff --git a/drivers/media/i2c/ar0521.c b/drivers/media/i2c/ar0521.c > > new file mode 100644 > > index 000000000000..0ab10bf2f99f > > --- /dev/null > > +++ b/drivers/media/i2c/ar0521.c > > @@ -0,0 +1,1065 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (C) 2021 Sieć Badawcza Łukasiewicz - Przemysłowy Instytut Automatyki i Pomiarów PIAP > > Over 80, please wrap. The same applies to the rest of the driver. > > > + * Written by Krzysztof Hałasa > > + */ > > + > > +#include <linux/clk.h> > > +#include <linux/clk-provider.h> > > +#include <linux/clkdev.h> > > +#include <linux/ctype.h> > > +#include <linux/delay.h> > > +#include <linux/device.h> > > +#include <linux/i2c.h> > > +#include <linux/init.h> > > +#include <linux/module.h> > > +#include <linux/of_device.h> > > +#include <linux/slab.h> > > +#include <linux/types.h> > > +#include <linux/gpio/consumer.h> > > +#include <linux/math64.h> > > +#include <linux/regulator/consumer.h> > > +#include <media/v4l2-async.h> > > +#include <media/v4l2-ctrls.h> > > +#include <media/v4l2-device.h> > > +#include <media/v4l2-event.h> > > +#include <media/v4l2-fwnode.h> > > +#include <media/v4l2-subdev.h> > > + > > +// External clock (extclk) frequencies > > +#define AR0521_EXTCLK_RATE (27 * 1000 * 1000) > > +#define AR0521_EXTCLK_MIN (10 * 1000 * 1000) > > +#define AR0521_EXTCLK_MAX (48 * 1000 * 1000) > > + > > +// PLL and PLL2 > > +#define AR0521_PLL_MIN (320 * 1000 * 1000) > > +#define AR0521_PLL_MAX (1280 * 1000 * 1000) > > + > > +// effective pixel clocks, the registers may be DDR > > +#define AR0521_PIXEL_CLOCK_MIN (168 * 1000 * 1000) > > +#define AR0521_PIXEL_CLOCK_MAX (414 * 1000 * 1000) > > + > > +#define AR0521_WIDTH_MIN 8u > > +#define AR0521_WIDTH_MAX 2608u > > +#define AR0521_HEIGHT_MIN 8u > > +#define AR0521_HEIGHT_MAX 1958u > > + > > +#define AR0521_WIDTH_BLANKING_MIN 572u > > +#define AR0521_HEIGHT_BLANKING_MIN 28u // must be even > > +#define AR0521_TOTAL_WIDTH_MIN 2968u > > + > > +// AR0521 registers > > +#define AR0521_REG_VT_PIX_CLK_DIV 0x0300 > > +#define AR0521_REG_FRAME_LENGTH_LINES 0x0340 > > + > > +#define AR0521_REG_CHIP_ID 0x3000 > > +#define AR0521_REG_COARSE_INTEGRATION_TIME 0x3012 > > +#define AR0521_REG_ROW_SPEED 0x3016 > > +#define AR0521_REG_EXTRA_DELAY 0x3018 > > +#define AR0521_REG_RESET 0x301A > > +#define AR0521_REG_RESET_DEFAULTS 0x0238 > > +#define AR0521_REG_RESET_GROUP_PARAM_HOLD 0x8000 > > +#define AR0521_REG_RESET_STREAM BIT(2) > > +#define AR0521_REG_RESET_RESTART BIT(1) > > +#define AR0521_REG_RESET_INIT BIT(0) > > + > > +#define AR0521_REG_GREEN1_GAIN 0x3056 > > +#define AR0521_REG_BLUE_GAIN 0x3058 > > +#define AR0521_REG_RED_GAIN 0x305A > > +#define AR0521_REG_GREEN2_GAIN 0x305C > > +#define AR0521_REG_GLOBAL_GAIN 0x305E > > + > > +#define AR0521_REG_HISPI_TEST_MODE 0x3066 > > +#define AR0521_REG_HISPI_TEST_MODE_LP11 0x0004 > > + > > +#define AR0521_REG_TEST_PATTERN_MODE 0x3070 > > + > > +#define AR0521_REG_SERIAL_FORMAT 0x31AE > > +#define AR0521_REG_SERIAL_FORMAT_MIPI 0x0200 > > + > > +#define AR0521_REG_HISPI_CONTROL_STATUS 0x31C6 > > +#define AR0521_REG_HISPI_CONTROL_STATUS_FRAMER_TEST_MODE_ENABLE 0x80 > > + > > +#define be cpu_to_be16 > > I think you could as well use the original macro. > > > + > > +// regulator supplies > > Please use C comments outside SPDX tags. This comment is redundant though. > > > +static const char * const ar0521_supply_names[] = { > > + "vdd_io", // I/O (1.8V) supply > > + "vdd", // Core, PLL and MIPI (1.2V) supply > > + "vaa", // Analog (2.7V) supply > > +}; > > + > > +#define AR0521_NUM_SUPPLIES ARRAY_SIZE(ar0521_supply_names) > > + > > +struct ar0521_ctrls { > > + struct v4l2_ctrl_handler handler; > > + struct v4l2_ctrl *exposure; > > + struct v4l2_ctrl *gain, *red_balance, *blue_balance; > > + struct v4l2_ctrl *test_pattern; > > + struct v4l2_ctrl *hblank, *vblank, *pixrate; > > +}; > > + > > +struct ar0521_dev { > > + struct i2c_client *i2c_client; > > + struct v4l2_subdev sd; > > + struct media_pad pad; > > + struct v4l2_fwnode_endpoint ep; > > + struct clk *extclk; > > + u32 extclk_freq; > > + > > + struct regulator *supplies[AR0521_NUM_SUPPLIES]; > > + struct gpio_desc *reset_gpio; > > + > > + // lock to protect all members below > > + struct mutex lock; > > + > > + struct v4l2_mbus_framefmt fmt; > > + struct v4l2_fract frame_interval, current_frame_interval; > > + struct ar0521_ctrls ctrls; > > + u32 pix_clk; > > + unsigned int power_count; > > + u16 total_width, total_height, pll_pre, pll_mult, pll_pre2, pll_mult2, extra_delay; > > + bool streaming; > > +}; > > + > > +static int debug; > > +module_param(debug, int, 0644); > > +MODULE_PARM_DESC(debug, "Debug level 0-3"); > > Could you rely on dynamic debug instead? > > > + > > +static inline struct ar0521_dev *to_ar0521_dev(struct v4l2_subdev *sd) > > +{ > > + return container_of(sd, struct ar0521_dev, sd); > > +} > > + > > +static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl) > > +{ > > + return &container_of(ctrl->handler, struct ar0521_dev, ctrls.handler)->sd; > > +} > > + > > +static inline unsigned int lanes(struct ar0521_dev *sensor) > > +{ > > + return sensor->ep.bus.mipi_csi2.num_data_lanes; > > +} > > + > > +static const char *mhz(u32 value) > > +{ > > + static char buff[32]; > > + > > + if (value % 1000) > > + sprintf(buff, "%u.%06u", value / (1000 * 1000), value % (1000 * 1000)); > > + else if (value % (1000 * 1000)) > > + sprintf(buff, "%u.%03u", value / (1000 * 1000), (value / 1000) % 1000); > > + else > > + sprintf(buff, "%u", value / (1000 * 1000)); > > + return buff; > > Sorry, you can't do that. buff is allocated in the stack and the memory is > no longer available once the function returns. It's a static char array, so it won't be allocated on the stack, but it's still bad practice as it's not thread-safe. Given that it's used in two debugging messages only, I'd hardcode the %u.06%u format in the callers. > > +} > > + > > +static u32 div64_round(u64 v, u32 d) > > +{ > > + return div_u64(v + (d >> 1), d); > > +} > > + > > +static u32 div64_round_up(u64 v, u32 d) > > +{ > > + return div_u64(v + d - 1, d); > > +} > > + > > +#define HEX_DUMP_WORDS 8 > > +static void dump_i2c(struct ar0521_dev *sensor, const __be16 *data, unsigned int count) > > +{ > > + char buffer[5 /* " XXXX" */ * HEX_DUMP_WORDS + 1 /* NUL */]; > > + u16 addr; > > + int i; > > + > > + addr = be16_to_cpu(*data++); > > + count--; > > + while (count) { > > + for (i = 0; i < HEX_DUMP_WORDS; i++) { > > + sprintf(buffer + 5 * i, " %04X", be16_to_cpu(*data++)); > > + addr += 2; > > + if (!--count) > > + break; > > + } > > + v4l2_dbg(3, debug, &sensor->sd, "WR %04X:%s\n", addr, buffer); > > + } > > +} > > + > > +// data must be BE16, the first value is the register address > > +static int ar0521_write_regs(struct ar0521_dev *sensor, const __be16 *data, unsigned int count) > > +{ > > + struct i2c_client *client = sensor->i2c_client; > > + struct i2c_msg msg; > > + int ret; > > + > > + if (!sensor->power_count) > > + return 0; > > + > > + if (debug >= 3) > > + dump_i2c(sensor, data, count); > > + > > + msg.addr = client->addr; > > + msg.flags = client->flags; > > + msg.buf = (u8 *)data; > > + msg.len = count * sizeof(*data); > > + > > + ret = i2c_transfer(client->adapter, &msg, 1); > > + if (ret < 0) { > > + v4l2_err(&sensor->sd, "%s: I2C write error\n", __func__); > > + return ret; > > + } > > + > > + return 0; > > +} > > + > > +static int ar0521_write_reg(struct ar0521_dev *sensor, u16 reg, u16 val) > > +{ > > + __be16 buf[2] = {be(reg), be(val)}; > > + > > + return ar0521_write_regs(sensor, buf, 2); > > +} > > + > > +static int ar0521_set_geometry(struct ar0521_dev *sensor) > > +{ > > + // all dimensions are unsigned 12-bit integers > > + u16 x = (AR0521_WIDTH_MAX - sensor->fmt.width) / 2; > > + u16 y = ((AR0521_HEIGHT_MAX - sensor->fmt.height) / 2) & ~1; > > + __be16 regs[] = { > > + be(AR0521_REG_FRAME_LENGTH_LINES), > > + be(sensor->total_height), > > + be(sensor->total_width), > > + be(x), > > + be(y), > > + be(x + sensor->fmt.width - 1), > > + be(y + sensor->fmt.height - 1), > > + be(sensor->fmt.width), > > + be(sensor->fmt.height) > > + }; > > + > > + v4l2_dbg(2, debug, &sensor->sd, "%s()\n", __func__); > > + > > + return ar0521_write_regs(sensor, regs, ARRAY_SIZE(regs)); > > +} > > + > > +static int ar0521_set_gains(struct ar0521_dev *sensor) > > +{ > > + int green = sensor->ctrls.gain->val; > > + int red = max(green + sensor->ctrls.red_balance->val, 0); > > + int blue = max(green + sensor->ctrls.blue_balance->val, 0); > > + unsigned int gain = min(red, min(green, blue)); > > + unsigned int analog = min(gain, 64u); // range is 0 - 127 > > + __be16 regs[5]; > > + > > + v4l2_dbg(2, debug, &sensor->sd, "%s()\n", __func__); > > + > > + red = min(red - analog + 64, 511u); > > + green = min(green - analog + 64, 511u); > > + blue = min(blue - analog + 64, 511u); > > + regs[0] = be(AR0521_REG_GREEN1_GAIN); > > + regs[1] = be(green << 7 | analog); > > + regs[2] = be(blue << 7 | analog); > > + regs[3] = be(red << 7 | analog); > > + regs[4] = be(green << 7 | analog); > > I think I'd use u16 for red, green and blue. Shifting signed integers can > result in undefined behaviour (MSB). > > > + > > + return ar0521_write_regs(sensor, regs, ARRAY_SIZE(regs)); > > +} > > + > > +static int ar0521_write_mode(struct ar0521_dev *sensor) > > +{ > > + __be16 pll_regs[] = { > > + be(AR0521_REG_VT_PIX_CLK_DIV), > > + /* 0x300 */ be(4), // vt_pix_clk_div = number of bits / 2 > > + /* 0x302 */ be(1), // vt_sys_clk_div > > + /* 0x304 */ be((sensor->pll_pre2 << 8) | sensor->pll_pre), > > + /* 0x306 */ be((sensor->pll_mult2 << 8) | sensor->pll_mult), > > + /* 0x308 */ be(8), // op_pix_clk_div = 2 * vt_pix_clk_div > > + /* 0x30A */ be(1) // op_sys_clk_div > > + }; > > + u32 num = sensor->current_frame_interval.numerator; > > + u32 denom = sensor->current_frame_interval.denominator; > > + int ret; > > + > > + v4l2_dbg(2, debug, &sensor->sd, "%s()\n", __func__); > > + > > + // stop streaming for just a moment > > + ret = ar0521_write_reg(sensor, AR0521_REG_RESET, AR0521_REG_RESET_DEFAULTS); > > + if (ret) > > + return ret; > > + > > + ret = ar0521_set_geometry(sensor); > > + if (ret) > > + return ret; > > + > > + ret = ar0521_write_regs(sensor, pll_regs, ARRAY_SIZE(pll_regs)); > > + if (ret) > > + return ret; > > + > > + ret = ar0521_write_reg(sensor, AR0521_REG_COARSE_INTEGRATION_TIME, sensor->ctrls.exposure->val); > > + if (ret) > > + return ret; > > + > > + ret = ar0521_write_reg(sensor, AR0521_REG_EXTRA_DELAY, sensor->extra_delay); > > + if (ret) > > + return ret; > > + > > + ret = ar0521_write_reg(sensor, AR0521_REG_RESET, AR0521_REG_RESET_DEFAULTS | AR0521_REG_RESET_STREAM); > > + if (ret) > > + return ret; > > + > > + ret = ar0521_write_reg(sensor, AR0521_REG_TEST_PATTERN_MODE, sensor->ctrls.test_pattern->val); > > + if (ret) > > + return ret; > > + > > + dev_info(&sensor->i2c_client->dev, > > + "AR0521: %ux%u, total %ux%u, pixel clock %s MHz, %u (%u/%u) FPS\n", > > + sensor->fmt.width, sensor->fmt.height, sensor->total_width, sensor->total_height, > > + mhz(sensor->pix_clk), (num + denom / 2) / denom, num, denom); > > dev_dbg() would seem more appropriate. > > Could you simply print the frequency in Hz? > > > + return 0; > > +} > > + > > +static int ar0521_set_stream(struct ar0521_dev *sensor, bool on) > > +{ > > + int ret; > > + > > + v4l2_dbg(2, debug, &sensor->sd, "%s(%u)\n", __func__, on); > > + > > + ret = ar0521_write_mode(sensor); > > + if (ret) > > + return ret; > > + > > + if (on) { > > + ret = ar0521_set_gains(sensor); > > + if (ret) > > + return ret; > > + > > + // normal output on clock and data lanes > > + ret = ar0521_write_reg(sensor, AR0521_REG_HISPI_CONTROL_STATUS, 0); > > + if (ret) > > + return ret; > > + } else { > > + // reset gain, the sensor may produce all white pixels without this > > + ret = ar0521_write_reg(sensor, AR0521_REG_GLOBAL_GAIN, 0x2000); > > + if (ret) > > + return ret; > > + > > + // set LP-11 on clock and data lanes > > + ret = ar0521_write_reg(sensor, AR0521_REG_HISPI_CONTROL_STATUS, > > + AR0521_REG_HISPI_CONTROL_STATUS_FRAMER_TEST_MODE_ENABLE); > > + if (ret) > > + return ret; > > + } > > + > > + // start streaming (possibly with LP-11 on all lines) > > + return ar0521_write_reg(sensor, AR0521_REG_RESET, > > + AR0521_REG_RESET_DEFAULTS | > > + AR0521_REG_RESET_RESTART | > > + AR0521_REG_RESET_STREAM); > > +} > > + > > +static u32 calc_pll(struct ar0521_dev *sensor, int num, u32 freq, u16 *pre_ptr, u16 *mult_ptr) > > +{ > > + u16 pre = 1, mult = 1, new_pre; > > + u32 pll = AR0521_PLL_MAX + 1; > > + > > + for (new_pre = 1; new_pre < 64; new_pre++) { > > + u32 new_pll; > > + u32 new_mult = div64_round_up((u64)freq * new_pre, sensor->extclk_freq); > > + > > + if (new_mult < 32) > > + continue; // minimum value > > + if (new_mult > 254) > > + break; // maximum, larger pre won't work either > > + if (sensor->extclk_freq * (u64)new_mult < AR0521_PLL_MIN * new_pre) > > + continue; > > + if (sensor->extclk_freq * (u64)new_mult > AR0521_PLL_MAX * new_pre) > > + break; // larger pre won't work either > > + new_pll = div64_round_up(sensor->extclk_freq * (u64)new_mult, new_pre); > > + if (new_pll < pll) { > > + pll = new_pll; > > + pre = new_pre; > > + mult = new_mult; > > + } > > + } > > + > > + pll = div64_round(sensor->extclk_freq * (u64)mult, pre); > > + *pre_ptr = pre; > > + *mult_ptr = mult; > > + return pll; > > +} > > + > > +static void ar0521_adj_fmt(struct v4l2_mbus_framefmt *fmt) > > +{ > > + fmt->width = clamp(ALIGN(fmt->width, 4), AR0521_WIDTH_MIN, AR0521_WIDTH_MAX); > > + fmt->height = clamp(ALIGN(fmt->height, 4), AR0521_HEIGHT_MIN, AR0521_HEIGHT_MAX); > > + fmt->code = MEDIA_BUS_FMT_SGRBG8_1X8; > > + fmt->field = V4L2_FIELD_NONE; > > + fmt->colorspace = V4L2_COLORSPACE_SRGB; > > + fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; > > + fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE; > > + fmt->xfer_func = V4L2_XFER_FUNC_DEFAULT; > > +} > > + > > +#define DIV 4 > > What does DIV signify? > > > +static void ar0521_calc_mode(struct ar0521_dev *sensor) > > +{ > > + unsigned int speed_mod = 4 / lanes(sensor); // 1 with 4 DDR lanes > > + u64 pix_clk; // for calculations > > + u32 pixels, num, denom, new_total_height, new_pixels; > > + u16 total_width, total_height; > > + > > + total_width = max(sensor->fmt.width + AR0521_WIDTH_BLANKING_MIN, AR0521_TOTAL_WIDTH_MIN); > > + total_height = sensor->fmt.height + AR0521_HEIGHT_BLANKING_MIN; > > + > > + pixels = total_width * total_height; > > + num = sensor->frame_interval.numerator; > > + denom = sensor->frame_interval.denominator; > > + > > + // calculate approximate pixel clock first > > + pix_clk = div64_round_up(pixels * (u64)num, denom); > > + if (pix_clk > AR0521_PIXEL_CLOCK_MAX) { > > + u32 cnt; > > + // have to recalculate FPS > > + num = pix_clk = AR0521_PIXEL_CLOCK_MAX; > > + denom = pixels; > > + // try to reduce the numbers a bit > > + for (cnt = 2; cnt * cnt < denom; cnt++) > > Braces would be nice here. > > > + while (num % cnt == 0 && denom % cnt == 0) { > > + num /= cnt; > > + denom /= cnt; > > + } > > + } else if (pix_clk < AR0521_PIXEL_CLOCK_MIN) > > + // we will compensate with total_height and extra_delay > > + pix_clk = AR0521_PIXEL_CLOCK_MIN; > > + > > + sensor->current_frame_interval.numerator = num; > > + sensor->current_frame_interval.denominator = denom; > > + > > + // PLL1 drives pixel clock - dual rate > > + pix_clk = calc_pll(sensor, 1, pix_clk * (DIV / 2), &sensor->pll_pre, &sensor->pll_mult); > > + pix_clk = div64_round(pix_clk, (DIV / 2)); > > + calc_pll(sensor, 2, pix_clk * (DIV / 2) * speed_mod, &sensor->pll_pre2, &sensor->pll_mult2); > > + > > + // let's see if we can do better > > + new_total_height = (div64_round((u64)pix_clk * denom, num) / total_width) & ~1; // must be even > > + if (new_total_height > total_height) { > > + total_height = new_total_height; > > + pixels = total_width * total_height; > > + } > > + > > + // maybe there is still room for improvement > > + new_pixels = div64_round(pix_clk * denom, num); > > + sensor->extra_delay = 0; > > + if (new_pixels > pixels) > > + sensor->extra_delay = new_pixels - pixels; > > + > > + sensor->pix_clk = pix_clk; > > + sensor->total_width = total_width; > > + sensor->total_height = total_height; > > +} > > + > > +static int ar0521_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_format *format) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + struct v4l2_mbus_framefmt *fmt; > > + > > + if (format->pad) > > + return -EINVAL; > > The caller has already checked for this as I understand you have a single > pad only (0). > > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s(%u)\n", __func__, format->which); > > + > > + mutex_lock(&sensor->lock); > > + > > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) > > + fmt = v4l2_subdev_get_try_format(&sensor->sd, sd_state, 0 /* pad */); > > + else > > + fmt = &sensor->fmt; > > + > > + format->format = *fmt; > > + > > + mutex_unlock(&sensor->lock); > > + return 0; > > +} > > + > > +static int ar0521_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_format *format) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + int ret = 0; > > + > > + if (format->pad) > > + return -EINVAL; > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s(%u)\n", __func__, format->which); > > + > > + ar0521_adj_fmt(&format->format); > > + > > + mutex_lock(&sensor->lock); > > + > > + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { > > + struct v4l2_mbus_framefmt *fmt; > > + > > + fmt = v4l2_subdev_get_try_format(sd, sd_state, 0 /* pad */); > > + *fmt = format->format; > > + } else { > > + sensor->fmt = format->format; > > + ar0521_calc_mode(sensor); > > + ret = ar0521_write_mode(sensor); > > + } > > + > > + mutex_unlock(&sensor->lock); > > + return ret; > > +} > > + > > +static int ar0521_s_ctrl(struct v4l2_ctrl *ctrl) > > +{ > > + struct v4l2_subdev *sd = ctrl_to_sd(ctrl); > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + int ret; > > + > > + // v4l2_ctrl_lock() locks our own mutex > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s(0x%X)\n", __func__, ctrl->id); > > + > > + switch (ctrl->id) { > > + case V4L2_CID_HBLANK: > > + case V4L2_CID_VBLANK: > > + sensor->total_width = sensor->fmt.width + sensor->ctrls.hblank->val; > > + sensor->total_height = sensor->fmt.width + sensor->ctrls.vblank->val; > > + ret = ar0521_set_geometry(sensor); > > + break; > > + case V4L2_CID_GAIN: > > + case V4L2_CID_RED_BALANCE: > > + case V4L2_CID_BLUE_BALANCE: > > + ret = ar0521_set_gains(sensor); > > + break; > > + case V4L2_CID_EXPOSURE: > > + ret = ar0521_write_reg(sensor, AR0521_REG_COARSE_INTEGRATION_TIME, ctrl->val); > > + break; > > + case V4L2_CID_TEST_PATTERN: > > + ret = ar0521_write_reg(sensor, AR0521_REG_TEST_PATTERN_MODE, ctrl->val); > > + break; > > + default: > > + ret = -EINVAL; > > + break; > > + } > > + > > + return ret; > > +} > > + > > +static const struct v4l2_ctrl_ops ar0521_ctrl_ops = { > > + .s_ctrl = ar0521_s_ctrl, > > +}; > > + > > +static const char * const test_pattern_menu[] = { > > + "Disabled", > > + "Solid color", > > + "Color bars", > > + "Faded color bars" > > +}; > > + > > +static int ar0521_init_controls(struct ar0521_dev *sensor) > > +{ > > + const struct v4l2_ctrl_ops *ops = &ar0521_ctrl_ops; > > + struct ar0521_ctrls *ctrls = &sensor->ctrls; > > + struct v4l2_ctrl_handler *hdl = &ctrls->handler; > > + int ret; > > + > > + v4l2_ctrl_handler_init(hdl, 32); > > + > > + // we can use our own mutex for the ctrl lock > > + hdl->lock = &sensor->lock; > > + > > + // manual gain > > + ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN, 0, 511, 1, 0); > > + ctrls->red_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_RED_BALANCE, -512, 511, 1, 0); > > + ctrls->blue_balance = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BLUE_BALANCE, -512, 511, 1, 0); > > + > > + // alternate for frame interval > > + ctrls->hblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HBLANK, AR0521_WIDTH_BLANKING_MIN, 4094, 1, AR0521_WIDTH_BLANKING_MIN); > > + ctrls->vblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VBLANK, AR0521_HEIGHT_BLANKING_MIN, 4094, 2, AR0521_HEIGHT_BLANKING_MIN); > > + // Read-only > > + ctrls->pixrate = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_PIXEL_RATE, AR0521_PIXEL_CLOCK_MIN, AR0521_PIXEL_CLOCK_MAX, 1, AR0521_PIXEL_CLOCK_MIN); > > + > > + // manual exposure time > > + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, 0, 65535, 1, 0); > > + > > + ctrls->test_pattern = v4l2_ctrl_new_std_menu_items(hdl, ops, V4L2_CID_TEST_PATTERN, > > + ARRAY_SIZE(test_pattern_menu) - 1, > > + 0, 0, test_pattern_menu); > > + > > + if (hdl->error) { > > + ret = hdl->error; > > + goto free_ctrls; > > + } > > + > > + sensor->sd.ctrl_handler = hdl; > > + return 0; > > + > > +free_ctrls: > > + v4l2_ctrl_handler_free(hdl); > > + return ret; > > +} > > + > > +static const struct initial_reg { > > + u16 addr, value; > > +} initial_regs[] = { > > + // corrections_recommended_bayer > > + {0x3042, 0x0004}, // RNC:enable b/w rnc mode > > + {0x3044, 0x4580}, // RNC:enable row noise correction > > + {0x30EE, 0x1136}, // RNC:rnc scaling factor-->initial recommended setting > > + {0x3120, 0x0001}, // recommended setting for dither > > + {0x3F2C, 0x442E}, // GTH_THRES_RTN: 7max,7min filtered out of every 46 > > + {0x30D2, 0x0000}, // CRM/CC: enable crm on Visible and CC rows > > + {0x30D4, 0x0000}, // CC: CC enabled with 16 samples per column > > + {0x30D6, 0x2FFF}, // CC: bw mode enabled/12 bit data resolution/bw mode > > + {0x30DA, 0x0FFF}, // CC: column correction clip level 2 is 0 > > + {0x30DC, 0x0FFF}, // CC: column correction clip level 3 is 0 > > + {0x30DE, 0x0000}, // CC: Group FPN correction > > + {0x31E0, 0x0781}, // Fuse/2DDC: enable 2ddc > > + {0x3180, 0x9434}, // FDOC:fdoc settings with fdoc every frame turned of > > + {0x3172, 0x0206}, // txlo clk divider options > > + {0x3F00, 0x0017}, // BM_T0 > > + {0x3F02, 0x02DD}, // BM_T1 > > + {0x3F04, 0x0020}, // if Ana_gain less than 2, use noise_floor0, multipl > > + {0x3F06, 0x0040}, // if Ana_gain between 4 and 7, use noise_floor2 and > > + {0x3F08, 0x0070}, // if Ana_gain between 4 and 7, use noise_floor2 and > > + {0x3F0A, 0x0101}, // Define noise_floor0(low address) and noise_floor1 > > + {0x3F0C, 0x0302}, // Define noise_floor2 and noise_floor3 > > + {0x3F1E, 0x0022}, > > + {0x3F1A, 0x01FF}, // cross factor 2 > > + {0x3F14, 0x0505}, // single k factor 2 > > + {0x3F44, 0x0707}, // couple k factor 2 > > + {0x3F18, 0x01FF}, // cross factor 1 > > + {0x3F12, 0x0505}, // single k factor 1 > > + {0x3F42, 0x1511}, // couple k factor 1 > > + {0x3F16, 0x01FF}, // cross factor 0 > > + {0x3F10, 0x0505}, // single k factor 0 > > + {0x3F40, 0x1511}, // couple k factor 0 > > + > > + // analog_setup_recommended_12bit > > + {0x3EB6, 0x004C}, // ECL > > + {0x3EBA, 0xAAAA}, > > + {0x3EBC, 0x0086}, // Bias currents for FSC/ECL > > + {0x3EC0, 0x1E00}, // SFbin/SH mode settings > > + {0x3EC2, 0x100B}, // CLK divider for ramp for 12 bit 400MHz mode only > > + {0x3EC4, 0x3300}, // FSC clamps for HDR mode and adc comp power down co > > + {0x3EC6, 0xEA44}, // VLN and clk gating controls > > + {0x3EC8, 0x6F6F}, // Txl0 and Txlo1 settings for normal mode > > + {0x3ECA, 0x2F4A}, // CDAC/Txlo2/RSTGHI/RSTGLO settings > > + {0x3ECC, 0x0506}, // RSTDHI/RSTDLO/CDAC/TXHI settings > > + {0x3ECE, 0x203B}, // Ramp buffer settings and Booster enable (bits 0-5) > > + {0x3ED0, 0x13F0}, // TXLO from atest/sf bin settings > > + {0x3ED2, 0x9A3D}, // Booster settings for reference rows/columns > > + {0x3ED4, 0x862F}, // TXLO open loop/row driver settings > > + {0x3ED6, 0x4081}, // Txlatch fr cfpn rows/vln bias > > + {0x3ED8, 0x4003}, // Ramp step setting for 12 bit 400 Mhz mode > > + {0x3EDA, 0x9A80}, // ramp offset for T1/normal and rst under range > > + {0x3EDC, 0xC000}, // over range for rst and under range for sig > > + {0x3EDE, 0xC103}, // over range for sig and col dec clk settings > > + {0x3426, 0x1600}, // ADC offset distribution pulse > > + {0x342A, 0x0038}, // pulse_config > > + {0x3F3E, 0x0001}, // Switch ADC from 10 bit to 12 bit mode > > + {0x341A, 0x6051}, > > + {0x3420, 0x6051}, > > + > > + // analog_setup_recommended_10bit > > + {0x3EC2, 0x100A}, // CLK divider for ramp for 10 bit 400MH > > + {0x3ED8, 0x8003}, // Ramp step setting for 10 bit 400 Mhz > > + {0x341A, 0x4735}, // Samp&Hold pulse in ADC > > + {0x3420, 0x4735}, // Samp&Hold pulse in ADC > > + {0x3426, 0x8A1A}, // ADC offset distribution pulse > > + {0x342A, 0x0018}, // pulse_config > > + {0x3ED2, 0xA53D}, // Ramp offset > > + {0x3EDA, 0xA580}, // Ramp Offset > > + {0x3EBA, 0xAAAD}, > > + {0x3EB6, 0x004C}, > > + {0x3F3E, 0x0000}, // Switch ADC from 12 bit to 10 bit mode > > + > > + // new RNC 10bit > > + {0x30EE, 0x1136}, // RNC:rnc scaling factor=*54/64 (32/38*64=53.9) > > + {0x3F2C, 0x442E}, // GTH_THRES_RTN: 4max,4min filtered out of every 46 samples and > > + // for 10bit mode > > + {0x301E, 0x00AA}, // PEDESTAL+2 :+2 is a workaround for 10bit mode +0.5 Rounding > > + {0x3120, 0x0005}, // p1 dither enabled for 10bit mode > > + > > + {0x0112, 0x0808}, // 8-bit/8-bit mode > > + {0x31BC, 0x068C}, // don't use continuous clock mode while shut down > > + {0x30FA, 0xFD00}, // GPIO0 = flash, GPIO1 = shutter > > + {0x31B0, 0x008B}, // frame_preamble - FIXME check WRT lanes# > > + {0x31B2, 0x0050}, // line_preamble - FIXME check WRT lanes# > > +}; > > + > > +static __be16 pixel_timing_recommended[] = { > > + be(0x3D00), // first register address > > + /* 3D00 */ be(0x043E), be(0x4760), be(0xFFFF), be(0xFFFF), be(0x8000), be(0x0510), be(0xAF08), be(0x0252), > > + /* 3D10 */ be(0x486F), be(0x5D5D), be(0x8056), be(0x8313), be(0x0087), be(0x6A48), be(0x6982), be(0x0280), > > + /* 3D20 */ be(0x8359), be(0x8D02), be(0x8020), be(0x4882), be(0x4269), be(0x6A95), be(0x5988), be(0x5A83), > > + /* 3D30 */ be(0x5885), be(0x6280), be(0x6289), be(0x6097), be(0x5782), be(0x605C), be(0xBF18), be(0x0961), > > + /* 3D40 */ be(0x5080), be(0x2090), be(0x4390), be(0x4382), be(0x5F8A), be(0x5D5D), be(0x9C63), be(0x8063), > > + /* 3D50 */ be(0xA960), be(0x9757), be(0x8260), be(0x5CFF), be(0xBF10), be(0x1681), be(0x0802), be(0x8000), > > + /* 3D60 */ be(0x141C), be(0x6000), be(0x6022), be(0x4D80), be(0x5C97), be(0x6A69), be(0xAC6F), be(0x4645), > > + /* 3D70 */ be(0x4400), be(0x0513), be(0x8069), be(0x6AC6), be(0x5F95), be(0x5F70), be(0x8040), be(0x4A81), > > + /* 3D80 */ be(0x0300), be(0xE703), be(0x0088), be(0x4A83), be(0x40FF), be(0xFFFF), be(0xFD70), be(0x8040), > > + /* 3D90 */ be(0x4A85), be(0x4FA8), be(0x4F8C), be(0x0070), be(0xBE47), be(0x8847), be(0xBC78), be(0x6B89), > > + /* 3DA0 */ be(0x6A80), be(0x6986), be(0x6B8E), be(0x6B80), be(0x6980), be(0x6A88), be(0x7C9F), be(0x866B), > > + /* 3DB0 */ be(0x8765), be(0x46FF), be(0xE365), be(0xA679), be(0x4A40), be(0x4580), be(0x44BC), be(0x7000), > > + /* 3DC0 */ be(0x8040), be(0x0802), be(0x10EF), be(0x0104), be(0x3860), be(0x5D5D), be(0x5682), be(0x1300), > > + /* 3DD0 */ be(0x8648), be(0x8202), be(0x8082), be(0x598A), be(0x0280), be(0x2048), be(0x3060), be(0x8042), > > + /* 3DE0 */ be(0x9259), be(0x865A), be(0x8258), be(0x8562), be(0x8062), be(0x8560), be(0x9257), be(0x8221), > > + /* 3DF0 */ be(0x10FF), be(0xB757), be(0x9361), be(0x1019), be(0x8020), be(0x9043), be(0x8E43), be(0x845F), > > + /* 3E00 */ be(0x835D), be(0x805D), be(0x8163), be(0x8063), be(0xA060), be(0x9157), be(0x8260), be(0x5CFF), > > + /* 3E10 */ be(0xFFFF), be(0xFFE5), be(0x1016), be(0x2048), be(0x0802), be(0x1C60), be(0x0014), be(0x0060), > > + /* 3E20 */ be(0x2205), be(0x8120), be(0x908F), be(0x6A80), be(0x6982), be(0x5F9F), be(0x6F46), be(0x4544), > > + /* 3E30 */ be(0x0005), be(0x8013), be(0x8069), be(0x6A80), be(0x7000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3E40 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3E50 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3E60 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3E70 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3E80 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3E90 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3EA0 */ be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), be(0x0000), > > + /* 3EB0 */ be(0x0000), be(0x0000), be(0x0000)}; > > + > > +static void ar0521_power_off(struct ar0521_dev *sensor) > > +{ > > + int i; > > unsigned int? > > Same for the rest of similar loops. > > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s()\n", __func__); > > + clk_disable_unprepare(sensor->extclk); > > + > > + if (sensor->reset_gpio) > > + gpiod_set_value(sensor->reset_gpio, 1); // assert RESET signal > > + > > + for (i = AR0521_NUM_SUPPLIES - 1; i >= 0; i--) { > > + if (sensor->supplies[i]) > > + regulator_disable(sensor->supplies[i]); > > + } > > +} > > + > > +static int ar0521_power_on(struct ar0521_dev *sensor) > > +{ > > + int i, ret; > > + unsigned int nlanes = lanes(sensor); > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s()\n", __func__); > > + for (i = 0; i < AR0521_NUM_SUPPLIES; i++) > > + if (sensor->supplies[i]) { > > + ret = regulator_enable(sensor->supplies[i]); > > + if (ret < 0) > > + goto off; > > + > > + usleep_range(1000, 1500); // min 1 ms > > + } > > + > > + ret = clk_prepare_enable(sensor->extclk); > > + if (ret < 0) { > > + v4l2_err(&sensor->sd, "error enabling sensor clock\n"); > > + goto off; > > + } > > + usleep_range(1000, 1500); // min 1 ms > > + > > + if (sensor->reset_gpio) > > + gpiod_set_value(sensor->reset_gpio, 0); // deassert RESET signal > > + usleep_range(4500, 5000); // min 45000 clocks > > + > > + for (i = 0; i < ARRAY_SIZE(initial_regs); i++) > > + if (ar0521_write_reg(sensor, initial_regs[i].addr, initial_regs[i].value)) > > + goto off; > > + > > + ret = ar0521_write_regs(sensor, pixel_timing_recommended, ARRAY_SIZE(pixel_timing_recommended)); > > + if (ret) > > + goto off; > > + > > + ret = ar0521_write_reg(sensor, AR0521_REG_SERIAL_FORMAT, AR0521_REG_SERIAL_FORMAT_MIPI | nlanes); > > + if (ret) > > + goto off; > > + > > + // set MIPI test mode - disabled for now > > + ret = ar0521_write_reg(sensor, AR0521_REG_HISPI_TEST_MODE, > > + ((0x40 << nlanes) - 0x40) | AR0521_REG_HISPI_TEST_MODE_LP11); > > + if (ret) > > + goto off; > > + > > + ret = ar0521_write_reg(sensor, AR0521_REG_ROW_SPEED, 0x110 | 4 / nlanes); > > + if (ret) > > + goto off; > > + > > + ar0521_calc_mode(sensor); > > + > > + ret = ar0521_set_stream(sensor, 0); > > + if (ret) > > + goto off; > > + > > + return 0; > > +off: > > + ar0521_power_off(sensor); > > + return ret; > > +} > > + > > +static int ar0521_s_power(struct v4l2_subdev *sd, int on) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s(%u, %s)\n", __func__, sensor->power_count, on ? "on" : "off"); > > + > > + if (on) { > > + if (!sensor->power_count++) { > > + int ret = ar0521_power_on(sensor); > > Could you instead use runtime PM? See e.g. the imx319 driver for an > example. > > > + > > + if (ret) { > > + sensor->power_count = 0; // undo > > + return ret; > > + } > > + } > > + } else if (!--sensor->power_count) > > + ar0521_power_off(sensor); > > + > > + return 0; > > +} > > + > > +static int ar0521_enum_mbus_code(struct v4l2_subdev *sd, struct v4l2_subdev_state *sd_state, > > + struct v4l2_subdev_mbus_code_enum *code) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + > > + if (code->pad || code->index) > > + return -EINVAL; > > + > > + code->code = sensor->fmt.code; > > + v4l2_dbg(1, debug, &sensor->sd, "%s() = %X\n", __func__, code->code); > > + return 0; > > +} > > + > > +static int ar0521_g_frame_interval(struct v4l2_subdev *sd, struct v4l2_subdev_frame_interval *fi) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + > > + mutex_lock(&sensor->lock); > > + fi->interval = sensor->current_frame_interval; > > + mutex_unlock(&sensor->lock); > > + v4l2_dbg(1, debug, &sensor->sd, "%s() = %u/%u\n", __func__, > > + fi->interval.numerator, fi->interval.denominator); > > + return 0; > > +} > > Virtually all new sensor drivers use the blanking controls to configure the > frame rate. Could you do the same? > > Also Documentation/driver-api/media/camera-sensor.rst . > > > + > > +static int ar0521_s_frame_interval(struct v4l2_subdev *sd, struct v4l2_subdev_frame_interval *fi) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + int ret; > > + > > + if (fi->pad) > > + return -EINVAL; > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s(%u/%u)\n", __func__, > > + fi->interval.numerator, fi->interval.denominator); > > + mutex_lock(&sensor->lock); > > + > > + if (sensor->streaming) { > > + ret = -EBUSY; > > + goto out; > > + } > > + > > + sensor->frame_interval = fi->interval; > > + ar0521_calc_mode(sensor); > > + ret = ar0521_write_mode(sensor); > > +out: > > + mutex_unlock(&sensor->lock); > > + return ret; > > +} > > + > > +static int ar0521_s_stream(struct v4l2_subdev *sd, int enable) > > +{ > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + int ret; > > + > > + v4l2_dbg(1, debug, &sensor->sd, "%s(%i)\n", __func__, enable); > > + mutex_lock(&sensor->lock); > > + > > + ret = ar0521_set_stream(sensor, enable); > > + sensor->streaming = enable; > > + > > + mutex_unlock(&sensor->lock); > > + return ret; > > +} > > + > > +static const struct v4l2_subdev_core_ops ar0521_core_ops = { > > + .log_status = v4l2_ctrl_subdev_log_status, > > + .s_power = ar0521_s_power, > > + .subscribe_event = v4l2_ctrl_subdev_subscribe_event, > > + .unsubscribe_event = v4l2_event_subdev_unsubscribe, > > +}; > > + > > +static const struct v4l2_subdev_video_ops ar0521_video_ops = { > > + .g_frame_interval = ar0521_g_frame_interval, > > + .s_frame_interval = ar0521_s_frame_interval, > > + .s_stream = ar0521_s_stream, > > +}; > > + > > +static const struct v4l2_subdev_pad_ops ar0521_pad_ops = { > > + .enum_mbus_code = ar0521_enum_mbus_code, > > + .get_fmt = ar0521_get_fmt, > > + .set_fmt = ar0521_set_fmt, > > +}; > > + > > +static const struct v4l2_subdev_ops ar0521_subdev_ops = { > > + .core = &ar0521_core_ops, > > + .video = &ar0521_video_ops, > > + .pad = &ar0521_pad_ops, > > +}; > > + > > +static int ar0521_probe(struct i2c_client *client, const struct i2c_device_id *id) > > +{ > > + struct device *dev = &client->dev; > > + struct fwnode_handle *endpoint; > > + struct ar0521_dev *sensor; > > + unsigned int cnt, nlanes; > > + int ret; > > + > > + v4l2_dbg(1, debug, client, "%s()\n", __func__); > > + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); > > + if (!sensor) > > + return -ENOMEM; > > + > > + sensor->i2c_client = client; > > + sensor->fmt.code = MEDIA_BUS_FMT_SGRBG8_1X8; > > + sensor->fmt.width = AR0521_WIDTH_MAX; > > + sensor->fmt.height = AR0521_HEIGHT_MAX; > > + sensor->fmt.field = V4L2_FIELD_NONE; > > + sensor->frame_interval.numerator = 30; > > + sensor->frame_interval.denominator = 1; > > + > > + endpoint = fwnode_graph_get_next_endpoint(of_fwnode_handle(dev->of_node), NULL); > > + if (!endpoint) { > > + dev_err(dev, "endpoint node not found\n"); > > + return -EINVAL; > > + } > > + > > + ret = v4l2_fwnode_endpoint_parse(endpoint, &sensor->ep); > > + fwnode_handle_put(endpoint); > > + if (ret) { > > + dev_err(dev, "could not parse endpoint\n"); > > + return ret; > > + } > > + > > + if (sensor->ep.bus_type != V4L2_MBUS_CSI2_DPHY) { > > Please assign the bus type before parsing the endpoint. > > > + dev_err(dev, "invalid bus type, must be MIPI CSI2\n"); > > + return -EINVAL; > > + } > > + > > + nlanes = lanes(sensor); > > Could you store the number of lanes to the device specific struct instead > of the entire parsed endpoint, if you only use this information? > > > + switch (nlanes) { > > + case 1: > > + case 2: > > + case 4: > > + break; > > + default: > > + dev_err(dev, "invalid number of MIPI data lane%s\n", nlanes > 1 ? "s" : ""); > > + return -EINVAL; > > + } > > + > > + // get master clock (extclk) > > + sensor->extclk = devm_clk_get(dev, "extclk"); > > + if (IS_ERR(sensor->extclk)) { > > + dev_err(dev, "failed to get extclk\n"); > > + return PTR_ERR(sensor->extclk); > > + } > > + > > + ret = clk_set_rate(sensor->extclk, AR0521_EXTCLK_RATE); > > + if (ret < 0) { > > + dev_err(dev, "error setting clock rate\n"); > > + return ret; > > + } > > + > > + sensor->extclk_freq = clk_get_rate(sensor->extclk); > > + > > + if (sensor->extclk_freq < AR0521_EXTCLK_MIN || > > + sensor->extclk_freq > AR0521_EXTCLK_MAX) { > > This is obviously the frequency range the device supports, but what is > assumed in the register lists? In other words, you should check for a > specific frequency. > > > + dev_err(dev, "extclk frequency out of range: %u Hz\n", sensor->extclk_freq); > > + return -EINVAL; > > + } > > + > > + // request optional reset pin (usually active low) and assert it > > + sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); > > + > > + v4l2_i2c_subdev_init(&sensor->sd, client, &ar0521_subdev_ops); > > + > > + sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS; > > + sensor->pad.flags = MEDIA_PAD_FL_SOURCE; > > + sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; > > + ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad); > > + if (ret) > > + return ret; > > + > > + for (cnt = 0; cnt < AR0521_NUM_SUPPLIES; cnt++) { > > + struct regulator *supply = devm_regulator_get(dev, ar0521_supply_names[cnt]); > > + > > + if (IS_ERR(supply)) { > > + dev_info(dev, "no %s regulator found: %li\n", ar0521_supply_names[cnt], PTR_ERR(supply)); > > + return PTR_ERR(supply); > > + } > > + sensor->supplies[cnt] = supply; > > + } > > + > > + mutex_init(&sensor->lock); > > + > > + ret = ar0521_init_controls(sensor); > > + if (ret) > > + goto entity_cleanup; > > + > > + ret = v4l2_async_register_subdev(&sensor->sd); > > + if (ret) > > + goto free_ctrls; > > + > > + ar0521_adj_fmt(&sensor->fmt); > > Please call this before registering the async subdev. > > > + > > + dev_info(dev, "AR0521 driver initialized, master clock frequency: %s MHz, %u MIPI data lanes\n", > > + mhz(sensor->extclk_freq), nlanes); > > I'd use dev_dbg(), if anything. > > > + return 0; > > + > > +free_ctrls: > > + v4l2_ctrl_handler_free(&sensor->ctrls.handler); > > +entity_cleanup: > > + media_entity_cleanup(&sensor->sd.entity); > > + mutex_destroy(&sensor->lock); > > + return ret; > > +} > > + > > +static int ar0521_remove(struct i2c_client *client) > > +{ > > + struct v4l2_subdev *sd = i2c_get_clientdata(client); > > + struct ar0521_dev *sensor = to_ar0521_dev(sd); > > + > > + v4l2_async_unregister_subdev(&sensor->sd); > > + media_entity_cleanup(&sensor->sd.entity); > > + v4l2_ctrl_handler_free(&sensor->ctrls.handler); > > + mutex_destroy(&sensor->lock); > > + return 0; > > +} > > + > > +static const struct i2c_device_id ar0521_id[] = { > > + {"ar0521", 0}, > > + {}, > > +}; > > +MODULE_DEVICE_TABLE(i2c, ar0521_id); > > Do you need the I²C device ID table? If not, please remove it. > > > + > > +static const struct of_device_id ar0521_dt_ids[] = { > > + {.compatible = "onnn,ar0521"}, > > + {} > > +}; > > +MODULE_DEVICE_TABLE(of, ar0521_dt_ids); > > + > > +static struct i2c_driver ar0521_i2c_driver = { > > + .driver = { > > + .name = "ar0521", > > + .of_match_table = ar0521_dt_ids, > > + }, > > + .id_table = ar0521_id, > > + .probe = ar0521_probe, > > + .remove = ar0521_remove, > > +}; > > + > > +module_i2c_driver(ar0521_i2c_driver); > > + > > +MODULE_DESCRIPTION("AR0521 MIPI Camera subdev driver"); > > +MODULE_AUTHOR("Krzysztof Hałasa <khalasa@xxxxxxx>"); > > +MODULE_LICENSE("GPL v2"); -- Regards, Laurent Pinchart
