Hi Martin, On Thu, Jul 15, 2021 at 09:37:24AM +0200, Martin Kepplinger wrote: > Am Mittwoch, dem 14.07.2021 um 21:24 +0300 schrieb Laurent Pinchart: > > On Wed, Jul 14, 2021 at 01:19:30PM +0200, Martin Kepplinger wrote: > > > Add a driver to support the i.MX8MQ MIPI CSI receiver. The hardware side > > > is based on > > > https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/media/platform/imx8/mxc-mipi-csi2_yav.c?h=imx_5.4.70_2.3.0 > > > > > > It's built as part of VIDEO_IMX7_CSI because that's documented to support > > > i.MX8M platforms. This driver adds i.MX8MQ support where currently only the > > > i.MX8MM platform has been supported. > > > > > > Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxx> > > > --- > > > drivers/staging/media/imx/Makefile | 1 + > > > drivers/staging/media/imx/imx8mq-mipi-csi2.c | 949 +++++++++++++++++++ > > > 2 files changed, 950 insertions(+) > > > create mode 100644 drivers/staging/media/imx/imx8mq-mipi-csi2.c > > > > > > diff --git a/drivers/staging/media/imx/Makefile > > > b/drivers/staging/media/imx/Makefile > > > index 6ac33275cc97..19c2fc54d424 100644 > > > --- a/drivers/staging/media/imx/Makefile > > > +++ b/drivers/staging/media/imx/Makefile > > > @@ -16,3 +16,4 @@ obj-$(CONFIG_VIDEO_IMX_CSI) += imx6-mipi-csi2.o [snip] > > > +static int imx8mq_mipi_csi_calc_hs_settle(struct csi_state *state) > > > +{ > > > + u32 width = state->format_mbus[MIPI_CSI2_PAD_SINK].width; > > > + u32 height = state->format_mbus[MIPI_CSI2_PAD_SINK].height; > > > + s64 link_freq; > > > + u32 lane_rate; > > > + > > > + /* Calculate the line rate from the pixel rate. */ > > > + link_freq = v4l2_get_link_freq(state->src_sd->ctrl_handler, > > > + state->csi2_fmt->width, > > > + state->bus.num_data_lanes * 2); > > > + if (link_freq < 0) { > > > + dev_err(state->dev, "Unable to obtain link frequency: %d\n", > > > + (int)link_freq); > > > + return link_freq; > > > + } > > > + > > > + lane_rate = link_freq * 2; > > > + if (lane_rate < 80000000 || lane_rate > 1500000000) { > > > + dev_dbg(state->dev, "Out-of-bound lane rate %u\n", lane_rate); > > > + return -EINVAL; > > > + } > > > + > > > + /* https://community.nxp.com/t5/i-MX-Processors/Explenation-for-HS-SETTLE-parameter-in-MIPI-CSI-D-PHY-registers/m-p/764275/highlight/true#M118744 */ > > > + if (lane_rate < 250000000) > > > + state->hs_settle = 0xb; > > > + else if (lane_rate < 500000000) > > > + state->hs_settle = 0x8; > > > + else > > > + state->hs_settle = 0x6; > > > > We could possibly compute this value based on the formula from the table > > in that page, but maybe that's overkill ? If you want to give it a try, > > it would be along those lines. > > > > /* > > * The D-PHY specification requires Ths-settle to be in the range > > * 85ns + 6*UI to 140ns + 10*UI, with the unit interval UI being half > > * the clock period. > > * > > * The Ths-settle value is expressed in the hardware as a multiple of > > * the Esc clock period: > > * > > * Ths-settle = (PRG_RXHS_SETTLE + 1) * Tperiod of RxClkInEsc > > * > > * Due to the one cycle inaccuracy introduced by rounding, the > > * documentation recommends picking a value away from the boundaries. > > * Let's pick the average. > > */ > > esc_clk_rate = clk_get_rate(...); > > > > min_ths_settle = 85 + 6 * 1000000 / (lane_rate / 1000); > > max_ths_settle = 140 + 10 * 1000000 / (lane_rate / 1000); > > ths_settle = (min_ths_settle + max_ths_settle) / 2; > > > > state->hs_settle = ths_settle * esc_clk_rate / 1000000000 - 1; > > I experimented a bit but would like to leave this as a task for later > if that's ok. it's correct and simple now. also, using clks[i].clk > based on the name string would feel better to submit seperately later. That's OK with me, but I may then submit a patch on top fairly soon :-) Have you been able to test if this code works on your device ? The main reason why I think it's better is that it doesn't hardcode a specific escape clock frequency assumption, so it should be able to accommodate a wider range of use cases. If we change it later, there's always a risk of regressions, while if we do this from the start, we'll figure out quickly if it doesn't work in some cases. -- Regards, Laurent Pinchart
