The :doc:`foo` tag is auto-generated via automarkup.py.
So, use the filename at the sources, instead of :doc:`foo`.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
---
Documentation/admin-guide/media/bt8xx.rst | 15 ++++++++-------
Documentation/admin-guide/media/bttv.rst | 21 +++++++++++----------
Documentation/admin-guide/media/saa7134.rst | 3 ++-
3 files changed, 21 insertions(+), 18 deletions(-)
diff --git a/Documentation/admin-guide/media/bt8xx.rst b/Documentation/admin-guide/media/bt8xx.rst
index 1382ada1e38e..3589f6ab7e46 100644
--- a/Documentation/admin-guide/media/bt8xx.rst
+++ b/Documentation/admin-guide/media/bt8xx.rst
@@ -15,11 +15,12 @@ Authors:
General information
-------------------
-This class of cards has a bt878a as the PCI interface, and require the bttv driver
-for accessing the i2c bus and the gpio pins of the bt8xx chipset.
+This class of cards has a bt878a as the PCI interface, and require the bttv
+driver for accessing the i2c bus and the gpio pins of the bt8xx chipset.
-Please see :doc:`bttv-cardlist` for a complete list of Cards based on the
-Conexant Bt8xx PCI bridge supported by the Linux Kernel.
+Please see Documentation/admin-guide/media/bttv-cardlist.rst for a complete
+list of Cards based on the Conexant Bt8xx PCI bridge supported by the
+Linux Kernel.
In order to be able to compile the kernel, some config options should be
enabled::
@@ -80,7 +81,7 @@ for dvb-bt8xx drivers by passing modprobe parameters may be necessary.
Running TwinHan and Clones
~~~~~~~~~~~~~~~~~~~~~~~~~~
-As shown at :doc:`bttv-cardlist`, TwinHan and
+As shown at Documentation/admin-guide/media/bttv-cardlist.rst, TwinHan and
clones use ``card=113`` modprobe parameter. So, in order to properly
detect it for devices without EEPROM, you should use::
@@ -105,12 +106,12 @@ The autodetected values are determined by the cards' "response string".
In your logs see f. ex.: dst_get_device_id: Recognize [DSTMCI].
For bug reports please send in a complete log with verbose=4 activated.
-Please also see :doc:`ci`.
+Please also see Documentation/admin-guide/media/ci.rst.
Running multiple cards
~~~~~~~~~~~~~~~~~~~~~~
-See :doc:`bttv-cardlist` for a complete list of
+See Documentation/admin-guide/media/bttv-cardlist.rst for a complete list of
Card ID. Some examples:
=========================== ===
diff --git a/Documentation/admin-guide/media/bttv.rst b/Documentation/admin-guide/media/bttv.rst
index 0ef1f203104d..125f6f47123d 100644
--- a/Documentation/admin-guide/media/bttv.rst
+++ b/Documentation/admin-guide/media/bttv.rst
@@ -24,7 +24,8 @@ If your board has digital TV, you'll also need::
./scripts/config -m DVB_BT8XX
-In this case, please see :doc:`bt8xx` for additional notes.
+In this case, please see Documentation/admin-guide/media/bt8xx.rst
+for additional notes.
Make bttv work with your card
-----------------------------
@@ -39,7 +40,7 @@ If it doesn't bttv likely could not autodetect your card and needs some
insmod options. The most important insmod option for bttv is "card=n"
to select the correct card type. If you get video but no sound you've
very likely specified the wrong (or no) card type. A list of supported
-cards is in :doc:`bttv-cardlist`.
+cards is in Documentation/admin-guide/media/bttv-cardlist.rst.
If bttv takes very long to load (happens sometimes with the cheap
cards which have no tuner), try adding this to your modules configuration
@@ -57,8 +58,8 @@ directory should be enough for it to be autoload during the driver's
probing mode (e. g. when the Kernel boots or when the driver is
manually loaded via ``modprobe`` command).
-If your card isn't listed in :doc:`bttv-cardlist` or if you have
-trouble making audio work, please read :ref:`still_doesnt_work`.
+If your card isn't listed in Documentation/admin-guide/media/bttv-cardlist.rst
+or if you have trouble making audio work, please read :ref:`still_doesnt_work`.
Autodetecting cards
@@ -77,8 +78,8 @@ the Subsystem ID in the second line, looks like this:
only bt878-based cards can have a subsystem ID (which does not mean
that every card really has one). bt848 cards can't have a Subsystem
ID and therefore can't be autodetected. There is a list with the ID's
-at :doc:`bttv-cardlist` (in case you are interested or want to mail
-patches with updates).
+at Documentation/admin-guide/media/bttv-cardlist.rst
+(in case you are interested or want to mail patches with updates).
.. _still_doesnt_work:
@@ -259,15 +260,15 @@ bug. It is very helpful if you can tell where exactly it broke
With a hard freeze you probably doesn't find anything in the logfiles.
The only way to capture any kernel messages is to hook up a serial
console and let some terminal application log the messages. /me uses
-screen. See :doc:`/admin-guide/serial-console` for details on setting
-up a serial console.
+screen. See Documentation/admin-guide/serial-console.rst for details on
+setting up a serial console.
-Read :doc:`/admin-guide/bug-hunting` to learn how to get any useful
+Read Documentation/admin-guide/bug-hunting.rst to learn how to get any useful
information out of a register+stack dump printed by the kernel on
protection faults (so-called "kernel oops").
If you run into some kind of deadlock, you can try to dump a call trace
-for each process using sysrq-t (see :doc:`/admin-guide/sysrq`).
+for each process using sysrq-t (see Documentation/admin-guide/sysrq.rst).
This way it is possible to figure where *exactly* some process in "D"
state is stuck.
diff --git a/Documentation/admin-guide/media/saa7134.rst b/Documentation/admin-guide/media/saa7134.rst
index 7ab9c70b9abe..51eae7eb5ab7 100644
--- a/Documentation/admin-guide/media/saa7134.rst
+++ b/Documentation/admin-guide/media/saa7134.rst
@@ -50,7 +50,8 @@ To build and install, you should run::
Once the new Kernel is booted, saa7134 driver should be loaded automatically.
Depending on the card you might have to pass ``card=<nr>`` as insmod option.
-If so, please check :doc:`saa7134-cardlist` for valid choices.
+If so, please check Documentation/admin-guide/media/saa7134-cardlist.rst
+for valid choices.
Once you have your card type number, you can pass a modules configuration
via a file (usually, it is either ``/etc/modules.conf`` or some file at
--
2.31.1
