Hi Martin, I have now found the datasheet, thanks to the link provided in a later patch in this series :-) Please see below for a few additional comments. On Tue, Jun 01, 2021 at 02:13:43AM +0300, Laurent Pinchart wrote: > On Mon, May 31, 2021 at 02:07:34PM +0200, Martin Kepplinger wrote: > > Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. > > > > Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxx> > > --- > > .../bindings/media/i2c/hynix,hi846.yaml | 99 +++++++++++++++++++ > > 1 file changed, 99 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > new file mode 100644 > > index 000000000000..26462f6b5e69 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml > > @@ -0,0 +1,99 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor > > + > > +maintainers: > > + - Martin Kepplinger <martin.kepplinger@xxxxxxx> > > + > > +description: |- > > + The Hi-846 is a raw image sensor with an MIPI CSI-2 image data > > + interface and CCI (I2C compatible) control bus. The output format > > + is 10bit Bayer. > > + > > +properties: > > + compatible: > > + const: hynix,hi846 > > + > > + reg: > > + maxItems: 1 > > + > > + clocks: > > + items: > > + - description: Reference to the mclk clock. > > + > > + clock-names: > > + items: > > + - const: mclk > > + > > + reset-gpios: > > + description: Reference to the GPIO connected to the reset pin. Active low. I'd write "RESETB pin" to match the datasheet. Could you add a property for the XSHUTDOWN GPIO too ? You can name it shutdown-gpios. > > + maxItems: 1 > > + > > + vdd-supply: > > + description: Definition of the regulator used as 1.8V digital power supply. There's no VDD signal, and the only 1.8V supply is VDDIO, which can also use 2.8V. This is thus ambiguous. How are the different sensor power rails supplied on your board ? > > + > > + port: > > + $ref: /schemas/graph.yaml#/properties/port > > + additionalProperties: false > > You can drop the additionalProperties, the graph schema has > unevaluatedProperties set to false already. > > > + > > + properties: > > + endpoint: > > + $ref: /schemas/media/video-interfaces.yaml# > > + unevaluatedProperties: false > > + > > + properties: > > + data-lanes: > > + oneOf: > > + - items: > > + - const: 1 > > + - const: 2 > > + - const: 3 > > + - const: 4 > > + - items: > > + - const: 1 > > + - const: 2 > > + > > + required: > > + - data-lanes > > + > > +required: > > + - compatible > > + - reg > > + - clocks > > + - clock-names > > + - reset-gpios > > I'd keep the reset-gpios property optional, in case the signal is > hardwired. > > I don't have access to the sensor datasheet, so I can't provide comments > on what may be missing. With the above two issues addressed, > > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > > > + - vdd-supply > > + - port > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + hi846: camera@20 { > > + compatible = "hynix,hi846"; > > + reg = <0x20>; > > + clocks = <&clk>; > > + clock-names = "mclk"; > > + vdd-supply = <®_camera_pwr_en>; /* 1.8v */ > > + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; > > + > > + port { > > + camera_out: endpoint { > > + remote-endpoint = <&csi1_ep1>; > > + data-lanes = <1 2>; > > + }; > > + }; > > + }; > > + }; > > + > > +... -- Regards, Laurent Pinchart
