Hi Rob,
Thank you for the patch.
On Wed, Mar 24, 2021 at 02:22:53PM -0600, Rob Herring wrote:
> The example in video-interfaces.yaml uses a bunch of undocumented
> bindings which will cause warnings when undocumented compatible checks
> are enabled. The example could be fixed to use documented bindings, but
> doing so would just duplicate other examples. So let's just remove the
> example.
>
> Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
> Cc: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> Cc: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Cc: linux-media@xxxxxxxxxxxxxxx
> Signed-off-by: Rob Herring <robh@xxxxxxxxxx>
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> ---
> v2: Drop instead of fixing the example
>
> .../bindings/media/video-interfaces.yaml | 127 ------------------
> 1 file changed, 127 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/media/video-interfaces.yaml b/Documentation/devicetree/bindings/media/video-interfaces.yaml
> index 0a7a73fd59f2..4391dce2caee 100644
> --- a/Documentation/devicetree/bindings/media/video-interfaces.yaml
> +++ b/Documentation/devicetree/bindings/media/video-interfaces.yaml
> @@ -215,130 +215,3 @@ properties:
> CCP2, for instance.
>
> additionalProperties: true
> -
> -examples:
> - # The example snippet below describes two data pipelines. ov772x and imx074
> - # are camera sensors with a parallel and serial (MIPI CSI-2) video bus
> - # respectively. Both sensors are on the I2C control bus corresponding to the
> - # i2c0 controller node. ov772x sensor is linked directly to the ceu0 video
> - # host interface. imx074 is linked to ceu0 through the MIPI CSI-2 receiver
> - # (csi2). ceu0 has a (single) DMA engine writing captured data to memory.
> - # ceu0 node has a single 'port' node which may indicate that at any time
> - # only one of the following data pipelines can be active:
> - # ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
> - - |
> - ceu@fe910000 {
> - compatible = "renesas,sh-mobile-ceu";
> - reg = <0xfe910000 0xa0>;
> - interrupts = <0x880>;
> -
> - mclk: master_clock {
> - compatible = "renesas,ceu-clock";
> - #clock-cells = <1>;
> - clock-frequency = <50000000>; /* Max clock frequency */
> - clock-output-names = "mclk";
> - };
> -
> - port {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* Parallel bus endpoint */
> - ceu0_1: endpoint@1 {
> - reg = <1>; /* Local endpoint # */
> - remote-endpoint = <&ov772x_1_1>; /* Remote phandle */
> - bus-width = <8>; /* Used data lines */
> - data-shift = <2>; /* Lines 9:2 are used */
> -
> - /* If hsync-active/vsync-active are missing,
> - embedded BT.656 sync is used */
> - hsync-active = <0>; /* Active low */
> - vsync-active = <0>; /* Active low */
> - data-active = <1>; /* Active high */
> - pclk-sample = <1>; /* Rising */
> - };
> -
> - /* MIPI CSI-2 bus endpoint */
> - ceu0_0: endpoint@0 {
> - reg = <0>;
> - remote-endpoint = <&csi2_2>;
> - };
> - };
> - };
> -
> - i2c {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - camera@21 {
> - compatible = "ovti,ov772x";
> - reg = <0x21>;
> - vddio-supply = <®ulator1>;
> - vddcore-supply = <®ulator2>;
> -
> - clock-frequency = <20000000>;
> - clocks = <&mclk 0>;
> - clock-names = "xclk";
> -
> - port {
> - /* With 1 endpoint per port no need for addresses. */
> - ov772x_1_1: endpoint {
> - bus-width = <8>;
> - remote-endpoint = <&ceu0_1>;
> - hsync-active = <1>;
> - vsync-active = <0>; /* Who came up with an
> - inverter here ?... */
> - data-active = <1>;
> - pclk-sample = <1>;
> - };
> - };
> - };
> -
> - camera@1a {
> - compatible = "sony,imx074";
> - reg = <0x1a>;
> - vddio-supply = <®ulator1>;
> - vddcore-supply = <®ulator2>;
> -
> - clock-frequency = <30000000>; /* Shared clock with ov772x_1 */
> - clocks = <&mclk 0>;
> - clock-names = "sysclk"; /* Assuming this is the
> - name in the datasheet */
> - port {
> - imx074_1: endpoint {
> - clock-lanes = <0>;
> - data-lanes = <1 2>;
> - remote-endpoint = <&csi2_1>;
> - };
> - };
> - };
> - };
> -
> - csi2: csi2@ffc90000 {
> - compatible = "renesas,sh-mobile-csi2";
> - reg = <0xffc90000 0x1000>;
> - interrupts = <0x17a0>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port@1 {
> - compatible = "renesas,csi2c"; /* One of CSI2I and CSI2C. */
> - reg = <1>; /* CSI-2 PHY #1 of 2: PHY_S,
> - PHY_M has port address 0,
> - is unused. */
> - csi2_1: endpoint {
> - clock-lanes = <0>;
> - data-lanes = <2 1>;
> - remote-endpoint = <&imx074_1>;
> - };
> - };
> - port@2 {
> - reg = <2>; /* port 2: link to the CEU */
> -
> - csi2_2: endpoint {
> - remote-endpoint = <&ceu0_0>;
> - };
> - };
> - };
> -
> -...
--
Regards,
Laurent Pinchart
