Hi Jacopo,
Thank you for the patch.
On Mon, Mar 15, 2021 at 02:15:00PM +0100, Jacopo Mondi wrote:
> Check the return value of the max9271_write() function in the
> max9271 library driver.
>
> While at it, modify an existing condition to be made identical
> to other checks.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> ---
> drivers/media/i2c/max9271.c | 30 +++++++++++++++++++++++-------
> 1 file changed, 23 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/media/i2c/max9271.c b/drivers/media/i2c/max9271.c
> index c495582dcff6..2c7dc7fb9846 100644
> --- a/drivers/media/i2c/max9271.c
> +++ b/drivers/media/i2c/max9271.c
> @@ -106,7 +106,10 @@ int max9271_set_serial_link(struct max9271_device *dev, bool enable)
> * Short delays here appear to show bit-errors in the writes following.
> * Therefore a conservative delay seems best here.
> */
> - max9271_write(dev, 0x04, val);
> + ret = max9271_write(dev, 0x04, val);
> + if (ret < 0)
> + return ret;
> +
> usleep_range(5000, 8000);
>
> return 0;
> @@ -118,7 +121,7 @@ int max9271_configure_i2c(struct max9271_device *dev, u8 i2c_config)
> int ret;
>
> ret = max9271_write(dev, 0x0d, i2c_config);
> - if (ret)
> + if (ret < 0)
> return ret;
>
> /* The delay required after an I2C bus configuration change is not
> @@ -143,7 +146,10 @@ int max9271_set_high_threshold(struct max9271_device *dev, bool enable)
> * Enable or disable reverse channel high threshold to increase
> * immunity to power supply noise.
> */
> - max9271_write(dev, 0x08, enable ? ret | BIT(0) : ret & ~BIT(0));
> + ret = max9271_write(dev, 0x08, enable ? ret | BIT(0) : ret & ~BIT(0));
> + if (ret < 0)
> + return ret;
> +
> usleep_range(2000, 2500);
>
> return 0;
> @@ -152,6 +158,8 @@ EXPORT_SYMBOL_GPL(max9271_set_high_threshold);
>
> int max9271_configure_gmsl_link(struct max9271_device *dev)
> {
> + int ret;
> +
> /*
> * Configure the GMSL link:
> *
> @@ -162,16 +170,24 @@ int max9271_configure_gmsl_link(struct max9271_device *dev)
> *
> * TODO: Make the GMSL link configuration parametric.
> */
> - max9271_write(dev, 0x07, MAX9271_DBL | MAX9271_HVEN |
> - MAX9271_EDC_1BIT_PARITY);
> + ret = max9271_write(dev, 0x07, MAX9271_DBL | MAX9271_HVEN |
> + MAX9271_EDC_1BIT_PARITY);
> + if (ret < 0)
> + return ret;
> +
> usleep_range(5000, 8000);
>
> /*
> * Adjust spread spectrum to +4% and auto-detect pixel clock
> * and serial link rate.
> */
> - max9271_write(dev, 0x02, MAX9271_SPREAD_SPECT_4 | MAX9271_R02_RES |
> - MAX9271_PCLK_AUTODETECT | MAX9271_SERIAL_AUTODETECT);
> + ret = max9271_write(dev, 0x02,
> + MAX9271_SPREAD_SPECT_4 | MAX9271_R02_RES |
> + MAX9271_PCLK_AUTODETECT |
> + MAX9271_SERIAL_AUTODETECT);
> + if (ret < 0)
> + return ret;
> +
> usleep_range(5000, 8000);
>
> return 0;
--
Regards,
Laurent Pinchart
