When configuring the CSI in imx7_csi_configure(), the CSICR18 is set
through a read-modify-write cycle to avoid affecting fields whose usage
isn't clear. The function then sets fields depending on whether the
input is interlaced or progressive, and from the parallel input or the
CSI-2 receiver.
Those bits are only set and never cleared. For instance, when switching
from a CSI-2 source to the parallel input, the BIT_DATA_FROM_MIPI will
stay set. Fix this issue by first clearing all the fields we need to
configure.
Add BIT_CSI_HW_ENABLE to the set of fields being cleared, as the CSI
needs to start in the disabled state. This allows dropping the call to
imx7_csi_hw_disable() in imx7_csi_sw_reset().
Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
---
drivers/staging/media/imx/imx7-media-csi.c | 13 ++++++-------
1 file changed, 6 insertions(+), 7 deletions(-)
diff --git a/drivers/staging/media/imx/imx7-media-csi.c b/drivers/staging/media/imx/imx7-media-csi.c
index bb6e2dac54a6..17fce3b42d87 100644
--- a/drivers/staging/media/imx/imx7-media-csi.c
+++ b/drivers/staging/media/imx/imx7-media-csi.c
@@ -333,8 +333,6 @@ static void imx7_csi_dmareq_rff_disable(struct imx7_csi *csi)
static void imx7_csi_sw_reset(struct imx7_csi *csi)
{
- imx7_csi_hw_disable(csi);
-
imx7_csi_rx_fifo_clear(csi);
imx7_csi_dma_reflash(csi);
@@ -451,17 +449,19 @@ static void imx7_csi_configure(struct imx7_csi *csi)
struct imx_media_video_dev *vdev = csi->vdev;
struct v4l2_pix_format *out_pix = &vdev->fmt;
int width = out_pix->width;
+ u32 stride = 0;
u32 cr1, cr18;
- u32 stride;
cr18 = imx7_csi_reg_read(csi, CSI_CSICR18);
+ cr18 &= ~(BIT_CSI_HW_ENABLE | BIT_MIPI_DATA_FORMAT_MASK |
+ BIT_DATA_FROM_MIPI | BIT_BASEADDR_CHG_ERR_EN |
+ BIT_BASEADDR_SWITCH_EN | BIT_BASEADDR_SWITCH_SEL |
+ BIT_DEINTERLACE_EN);
+
if (out_pix->field == V4L2_FIELD_INTERLACED) {
cr18 |= BIT_DEINTERLACE_EN;
stride = out_pix->width;
- } else {
- cr18 &= ~BIT_DEINTERLACE_EN;
- stride = 0;
}
if (!csi->is_csi2) {
@@ -478,7 +478,6 @@ static void imx7_csi_configure(struct imx7_csi *csi)
cr1 = BIT_SOF_POL | BIT_REDGE | BIT_HSYNC_POL | BIT_FCC
| BIT_MCLKDIV(1) | BIT_MCLKEN;
- cr18 &= BIT_MIPI_DATA_FORMAT_MASK;
cr18 |= BIT_DATA_FROM_MIPI;
switch (csi->format_mbus[IMX7_CSI_PAD_SINK].code) {
--
Regards,
Laurent Pinchart
