Re: [PATCH v2 47/48] ARM: tegra: ventana: Support CPU voltage scaling and thermal throttling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



17.12.2020 21:28, Daniel Lezcano пишет:
> On 17/12/2020 19:06, Dmitry Osipenko wrote:
>> Enable CPU voltage scaling and thermal throttling on Tegra20 Ventana board.
>>
>> Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
>> ---
>>  arch/arm/boot/dts/tegra20-ventana.dts | 40 ++++++++++++++++++++++++++-
>>  1 file changed, 39 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/tegra20-ventana.dts
>> index 14ace2ef749c..c2d9f38960bc 100644
>> --- a/arch/arm/boot/dts/tegra20-ventana.dts
>> +++ b/arch/arm/boot/dts/tegra20-ventana.dts
>> @@ -2,8 +2,10 @@
>>  /dts-v1/;
>>  
>>  #include <dt-bindings/input/input.h>
>> +#include <dt-bindings/thermal/thermal.h>
>>  #include "tegra20.dtsi"
>>  #include "tegra20-cpu-opp.dtsi"
>> +#include "tegra20-cpu-opp-microvolt.dtsi"
>>  
>>  / {
>>  	model = "NVIDIA Tegra20 Ventana evaluation board";
>> @@ -527,9 +529,10 @@ ldo_rtc {
>>  			};
>>  		};
>>  
>> -		temperature-sensor@4c {
>> +		nct1008: temperature-sensor@4c {
>>  			compatible = "onnn,nct1008";
>>  			reg = <0x4c>;
>> +			#thermal-sensor-cells = <1>;
>>  		};
>>  	};
>>  
>> @@ -615,10 +618,13 @@ clk32k_in: clock@0 {
>>  
>>  	cpus {
>>  		cpu0: cpu@0 {
>> +			cpu-supply = <&vdd_cpu>;
>>  			operating-points-v2 = <&cpu0_opp_table>;
>> +			#cooling-cells = <2>;
>>  		};
>>  
>>  		cpu@1 {
>> +			cpu-supply = <&vdd_cpu>;
>>  			operating-points-v2 = <&cpu0_opp_table>;
>>  		};
>>  	};
>> @@ -717,4 +723,36 @@ sound {
>>  			 <&tegra_car TEGRA20_CLK_CDEV1>;
>>  		clock-names = "pll_a", "pll_a_out0", "mclk";
>>  	};
>> +
>> +	thermal-zones {
>> +		cpu-thermal {
>> +			polling-delay-passive = <1000>; /* milliseconds */
>> +			polling-delay = <5000>; /* milliseconds */
>> +
>> +			thermal-sensors = <&nct1008 1>;
>> +
>> +			trips {
>> +				trip0: cpu-alert0 {
>> +					/* start throttling at 50C */
>> +					temperature = <50000>;
>> +					hysteresis = <200>;
> 
> Did you mean <2000> ?

The <200> is correct.

Please see this commit for example:

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=2b22393b27670b45a2c870bce3df6579efd9a86a

>> +					type = "passive";
>> +				};
>> +
>> +				trip1: cpu-crit {
>> +					/* shut down at 60C */
>> +					temperature = <60000>;
>> +					hysteresis = <2000>;
> 
> I think you can drop the hysteresis here, when the critical temperature
> is reached, there is an emergency shutdown.

Yes, perhaps you're right. Hysteresis doesn't make sense for a critical
trip. I'll improve it in the next revision, thanks.

> 50°C and 60°C sound very low values, no ?

Tegra20 CPU is very cold in comparison to later generations, it should
stay under 50°C even at a full load.

>> +					type = "critical";
>> +				};
>> +			};
>> +
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&trip0>;
>> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> 
> You should add all CPUs here.


All CPU cores are coupled on Tegra in regards to CPUFreq, hence I think
it won't make any difference if secondary CPU cores will be added here,
isn't it?



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux