Hello,
I'm trying to get a Terratec S7 to work. The driver, just cloned
v4l-dvb, compiles and loads fine but when I try to scan Astra 19.2E only
a few stations get scanned. In most cases I get a tuning error. Under
Win7 the box works perfectly, so it's not a hardware defect or antenna
specific issue.
Any help would be very appreciated.
Information about my system:
- Core i5 661 running on Gigabyte board
# uname -a
Linux mmedia 2.6.33-020633-generic #020633 SMP Thu Feb 25 10:10:03 UTC
2010 x86_64 GNU/Linux
# lsusb -v -s 002:004
Bus 002 Device 004: ID 0ccd:10ac TerraTec Electronic GmbH
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0ccd TerraTec Electronic GmbH
idProduct 0x10ac
bcdDevice 0.03
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 100
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)
# lsmod
lsmod
Module Size Used by
dvb_usb_az6027 16534 1
stb6100 6772 1 dvb_usb_az6027
stb0899 34318 1 dvb_usb_az6027
dvb_usb 19392 1 dvb_usb_az6027
dvb_core 101054 2 dvb_usb_az6027,dvb_usb
binfmt_misc 7901 1
ppdev 6503 0
bridge 50766 0
stp 2059 1 bridge
bnep 11733 2
snd_hda_codec_intelhdmi 18424 1
snd_hda_codec_realtek 285848 1
snd_hda_intel 27340 1
snd_hda_codec 87794 3
snd_hda_codec_intelhdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 6686 1 snd_hda_codec
snd_pcm_oss 42660 0
snd_mixer_oss 17285 1 snd_pcm_oss
snd_pcm 87952 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1836 0
snd_seq_oss 30234 0
snd_seq_midi 5722 0
snd_rawmidi 22532 1 snd_seq_midi
snd_seq_midi_event 6867 2 snd_seq_oss,snd_seq_midi
snd_seq 55304 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 23536 2 snd_pcm,snd_seq
snd_seq_device 6520 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
k8temp 4056 0
iptable_filter 2743 0
snd 69404 15
snd_hda_codec_intelhdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
it87 24835 0
soundcore 7945 1 snd
ip_tables 18228 1 iptable_filter
snd_page_alloc 8476 2 snd_hda_intel,snd_pcm
x_tables 21305 1 ip_tables
hwmon_vid 3083 1 it87
lp 10024 0
btusb 12784 2
serio_raw 4893 0
parport 38004 2 ppdev,lp
xfs 927033 10
exportfs 4243 1 xfs
fbcon 39731 72
tileblit 2311 1 fbcon
font 8005 1 fbcon
bitblit 5213 1 fbcon
softcursor 1485 1 bitblit
i915 315226 2
drm_kms_helper 30180 1 i915
pata_it8213 3970 0
r8169 41344 0
mii 4933 1 r8169
drm 195147 3 i915,drm_kms_helper
i2c_algo_bit 5830 1 i915
video 22073 1 i915
intel_agp 28717 1
output 2391 1 video
# dmesg
[ 514.230862] usb 2-5: new high speed USB device using ehci_hcd and
address 4
[ 514.636137] dvb-usb: found a 'TERRATEC S7 MKII' in cold state, will
try to load a firmware
[ 514.636142] usb 2-5: firmware: requesting dvb-usb-az6027-03.fw
[ 514.671231] dvb-usb: downloading firmware from file
'dvb-usb-az6027-03.fw'
[ 514.745683] dvb-usb: found a 'TERRATEC S7 MKII' in warm state.
[ 514.745740] dvb-usb: will pass the complete MPEG2 transport stream to
the software demuxer.
[ 514.963579] DVB: registering new adapter (TERRATEC S7 MKII)
[ 516.942119] stb0899_attach: Attaching STB0899
[ 516.942126] stb6100_attach: Attaching STB6100
[ 516.942606] DVB: registering adapter 0 frontend 0 (STB0899
Multistandard)...
[ 516.942737] input: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:1d.7/usb2/2-5/input/input4
[ 516.942788] dvb-usb: schedule remote query interval to 400 msecs.
[ 516.942794] dvb-usb: TERRATEC S7 MKII successfully initialized and
connected.
[ 516.942844] usbcore: registered new interface driver dvb_usb_az6027
Here some output from w_scan during scan. With scan-s2 it's the same, I
always get "tuning failed".
Thank you for any assistance in advance and best regards,
Jens
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
