Hi,
Here's a series introducing the CEC support for the BCM2711 found on the
RaspberryPi4.
The BCM2711 HDMI controller uses a similar layout for the CEC registers, the
main difference being that the interrupt handling part is now shared between
both HDMI controllers.
This series is mainly about fixing a couple of bugs, reworking the driver to
support having two different interrupts, one for each direction, provided by an
external irqchip, and enables the irqchip driver for the controller we have.
This has been tested on an RPi3 and RPi4, but requires the latest firmware.
It's is based on the 10 and 12 bpc series.
Here is the cec-compliance output:
$ cec-ctl --tuner -p 1.0.0.0
The CEC adapter doesn't allow setting the physical address manually, ignore this option.
Driver Info:
Driver Name : vc4_hdmi
Adapter Name : vc4
Capabilities : 0x0000010e
Logical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask : 0x0008
CEC Version : 2.0
Vendor ID : 0x000c03 (HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
None
$ cec-compliance
cec-compliance SHA : not available
Driver Info:
Driver Name : vc4_hdmi
Adapter Name : vc4
Capabilities : 0x0000010e
Logical Addresses
Transmit
Passthrough
Driver version : 5.10.0
Available Logical Addresses: 1
Physical Address : 1.0.0.0
Logical Address Mask : 0x0008
CEC Version : 2.0
Vendor ID : 0x000c03 (HDMI)
OSD Name : Tuner
Logical Addresses : 1 (Allow RC Passthrough)
Logical Address : 3 (Tuner 1)
Primary Device Type : Tuner
Logical Address Type : Tuner
All Device Types : Tuner
RC TV Profile : None
Device Features :
None
Compliance test for vc4_hdmi device /dev/cec0:
The test results mean the following:
OK Supported correctly by the device.
OK (Not Supported) Not supported and not mandatory for the device.
OK (Presumed) Presumably supported. Manually check to confirm.
OK (Unexpected) Supported correctly but is not expected to be supported for this device.
OK (Refused) Supported by the device, but was refused.
FAIL Failed and was expected to be supported by this device.
Find remote devices:
Polling: OK
Network topology:
System Information for device 0 (TV) from device 3 (Tuner 1):
CEC Version : 2.0
Physical Address : 0.0.0.0
Primary Device Type : TV
Vendor ID : 0x000c03 (HDMI)
OSD Name : 'test-124'
Power Status : Tx, OK, Rx, OK, Feature Abort
Total for vc4_hdmi device /dev/cec0: 1, Succeeded: 1, Failed: 0, Warnings: 0
Let me know what you think,
Maxime
Dom Cobley (5):
drm/vc4: hdmi: Move hdmi reset to bind
drm/vc4: hdmi: Fix register offset with longer CEC messages
drm/vc4: hdmi: Fix up CEC registers
drm/vc4: hdmi: Restore cec physical address on reconnect
drm/vc4: hdmi: Remove cec_available flag
Maxime Ripard (10):
irqchip: Allow to compile bcmstb on other platforms
drm/vc4: hdmi: Compute the CEC clock divider from the clock rate
drm/vc4: hdmi: Update the CEC clock divider on HSM rate change
drm/vc4: hdmi: Introduce a CEC clock
drm/vc4: hdmi: Split the interrupt handlers
drm/vc4: hdmi: Support BCM2711 CEC interrupt setup
drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts
dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add the CEC interrupt controller
.../bindings/display/brcm,bcm2711-hdmi.yaml | 20 +-
arch/arm/boot/dts/bcm2711.dtsi | 30 +++
drivers/gpu/drm/vc4/vc4_hdmi.c | 224 +++++++++++++-----
drivers/gpu/drm/vc4/vc4_hdmi.h | 11 +-
drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 4 +-
drivers/irqchip/Kconfig | 2 +-
6 files changed, 232 insertions(+), 59 deletions(-)
--
2.28.0
