Re: [PATCH v3 3/6] ARM: dts: sun8i: v3s: Add node for system control

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 12/3/20 10:44 AM, Chen-Yu Tsai wrote:
> On Fri, Dec 4, 2020 at 12:25 AM Martin Cerveny <martin@xxxxxxxxx> wrote:
>>
>> Hello.
>>
>> On Thu, 3 Dec 2020, Chen-Yu Tsai wrote:
>>
>>> Hi,
>>>
>>> On Mon, Nov 16, 2020 at 8:57 PM Martin Cerveny <m.cerveny@xxxxxxxxxxxx> wrote:
>>>>
>>>> Allwinner V3s has system control and SRAM C1 region similar to H3.
>>>>
>>>> Signed-off-by: Martin Cerveny <m.cerveny@xxxxxxxxxxxx>
>>>> ---
>>>>  arch/arm/boot/dts/sun8i-v3s.dtsi | 14 ++++++++++++++
>>>>  1 file changed, 14 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
>>>> index 0c7341676921..70193512c222 100644
>>>> --- a/arch/arm/boot/dts/sun8i-v3s.dtsi
>>>> +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
>>>> @@ -161,6 +161,20 @@ syscon: system-control@1c00000 {
>>>>                         #address-cells = <1>;
>>>>                         #size-cells = <1>;
>>>>                         ranges;
>>>> +
>>>> +                       sram_c: sram@1d00000 {
>>>> +                               compatible = "mmio-sram";
>>>> +                               reg = <0x01d00000 0x80000>;
>>>
>>> How was this address derived? Did you check that there is actually SRAM here?
>>
>> Yes, I did some checking (mmap). But I repeated measurement and found
>> mirrored regions:
>>
>> - SRAM_C is mirrored from 0x0000_4000 (primary location) to 0x01d0_4000 (size 0xb000)
>>    (probably exact size is 0xb0c0)
>> - rest of 0x01d0_0000 are discontinuously filled with R/W register sets
>>    (probably some internals registers from VE) that I thought to be SRAM too
>> - register SRAM_CTRL_REG0==0x01c00_0000 (value 0x7fff_ffff) switch whole
>>    region 0x01d0_0000-0x01df_ffff __AND__ 0x0000_4000-0x0000_ffff
>> - VE/cedrus code use this regions indirectly
>>    (VE_AVC_SRAM_PORT_OFFSET/VE_AVC_SRAM_PORT_DATA...)
>>    and it is not influenced by "true" SRAM mapping or size
> 
> Could you add this to your commit log? That would make the information
> available to others, and you could mention that you only added the
> location that is contiguous SRAM without the interspersed registers.
> 
> So based on this, and what we've seen with the H616, I'm guessing
> 0x01d0_0000 - 0x01df_ffff exposes all the internal guts of the VE,
> while SRAM C @ 0x4000 just maps a small portion out.
> 
>> -> so I suppose to better use only SRAM_C lower definition:
> 
> Yes that would be more appropriate, as it matches the manual, and as you
> mentioned, is *real* SRAM.

My reading of the manual and comments in the BSP U-Boot is that the high
address near the VE registers is the "real" address. The alternate SRAM
mapping just past the end of SRAM A1 exists specifically so the boot ROM
can load boot0/TOC0 images larger than would fit in SRAM A1.

I don't have a copy of the V3s BROM, but here's the logic from the
beginning of the H6 SBROM, which first enables the VE bus clock and
reset before mapping the SRAM:

; VE_BGR_REG |= BIT(16)
     2dc:  e59f113c  ldr r1, [pc, #316] ; 420
     2e0:  e5912000  ldr r2, [r1]
     2e4:  e3a03801  mov r3, #65536 ; 0x10000
     2e8:  e1822003  orr r2, r2, r3
     2ec:  e5812000  str r2, [r1]
; VE_BGR_REG |= BIT(0)
     2f0:  e59f1128  ldr r1, [pc, #296] ; 420
     2f4:  e5912000  ldr r2, [r1]
     2f8:  e3a03001  mov r3, #1
     2fc:  e1822003  orr r2, r2, r3
     300:  e5812000  str r2, [r1]
; SRAM_CTRL_REG0 &= BIT(31)
     304:  e3a01403  mov r1, #50331648 ; 0x3000000
     308:  e5912000  ldr r2, [r1]
     30c:  e3c220ff  bic r2, r2, #255 ; 0xff
     310:  e3c22cff  bic r2, r2, #65280 ; 0xff00
     314:  e3c228ff  bic r2, r2, #16711680 ; 0xff0000
     318:  e3c2247f  bic r2, r2, #2130706432 ; 0x7f000000
     31c:  e5812000  str r2, [r1]
; SRAM_CTRL_REG1 = BIT(24) | BIT(0)
     320:  e59f10fc  ldr r1, [pc, #252] ; 424
     324:  e3a02401  mov r2, #16777216 ; 0x1000000
     328:  e1822003  orr r2, r2, r3
     32c:  e5812000  str r2, [r1]
...
     420:  .word 0300169c
     424:  .word 03000004

Then U-Boot SPL[1] sets the SRAM back to "normal mode" before turning
off the VE gating and reset:

	//VE SRAM:set sram to normal mode, default boot mode
	reg_val = readl(SUNXI_SYSCRL_BASE+0X0004);
	reg_val &= ~(0x1<<24);
	writel(reg_val, SUNXI_SYSCRL_BASE+0X0004);

	//VE gating&VE Bus Reset :brom set them, but not require now
	reg_val = readl(CCMU_VE_BGR_REG);
	reg_val &= ~(0x1<<0);
	reg_val &= ~(0x1<<16);
	writel(reg_val, CCMU_VE_BGR_REG);

Other SoCs have a similar code to unmap SRAM C[2]. The AHB1 bus clock
frequency limitation makes sense given that it has to go through the VE
hardware block to get to the SRAM.

In fact, the AHB1 clock limitation when using the low mapping should be
reason enough to prefer the high mapping.

Cheers,
Samuel

[1]:
https://github.com/Allwinner-Homlet/H6-BSP4.9-brandy/blob/master/u-boot-2014.07/board/sunxi/sun50iw6p1/sun50iw6p1.c#L60
[2]:
https://github.com/Allwinner-Homlet/H6-BSP4.9-brandy/blob/master/u-boot-2014.07/board/sunxi/sun8iw10p1/sun8iw10p1.c#L75

>> ---
>> diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
>> index e8f304125e2d..90d703e5b73b 100644
>> --- a/arch/arm/boot/dts/sun8i-v3s.dtsi
>> +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
>> @@ -162,17 +162,17 @@ syscon: system-control@1c00000 {
>>                         #size-cells = <1>;
>>                         ranges;
>>
>> -                       sram_c: sram@1d00000 {
>> +                       sram_c: sram@4000 {
>>                                 compatible = "mmio-sram";
>> -                               reg = <0x01d00000 0x80000>;
>> +                               reg = <0x4000 0xb000>;
>>                                 #address-cells = <1>;
>>                                 #size-cells = <1>;
>> -                               ranges = <0 0x01d00000 0x80000>;
>> +                               ranges = <0 0 0x4000 0xb000>;
>>
>>                                 ve_sram: sram-section@0 {
>>                                         compatible = "allwinner,sun8i-v3s-sram-c1",
>>                                                      "allwinner,sun4i-a10-sram-c1";
>> -                                       reg = <0x000000 0x80000>;
>> +                                       reg = <0x0 0xb000>;
>>                                 };
>>                         };
>>                 };
>> ---
>>
>> Does someone have accessible specific documentation of VE/cedrus for V3s ?
> 
> I doubt such information exists.
> 
> 
> Regards
> ChenYu
> 
>> Regards, Martin
>>
>>> ChenYu
>>>
>>>> +                               #address-cells = <1>;
>>>> +                               #size-cells = <1>;
>>>> +                               ranges = <0 0x01d00000 0x80000>;
>>>> +
>>>> +                               ve_sram: sram-section@0 {
>>>> +                                       compatible = "allwinner,sun8i-v3s-sram-c1",
>>>> +                                                    "allwinner,sun4i-a10-sram-c1";
>>>> +                                       reg = <0x000000 0x80000>;
>>>> +                               };
>>>> +                       };
>>>>                 };
>>>>
>>>>                 tcon0: lcd-controller@1c0c000 {
>>>> --
>>>> 2.25.1
>>>>
>>>>
>>>> _______________________________________________
>>>> linux-arm-kernel mailing list
>>>> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
>>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>>
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux