From: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
Add support for an optional GPIO connected to PWDN on the sensor. This
allows the use of hardware standby mode where internal device clock
and circuit activities are halted.
Please note that power is off when PWDN is high.
Signed-off-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@xxxxxxxxxxxxxxx>
Signed-off-by: Jacopo Mondi <jacopo@xxxxxxxxxx>
---
drivers/media/i2c/ov5647.c | 32 ++++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/drivers/media/i2c/ov5647.c b/drivers/media/i2c/ov5647.c
index e7d2e5b4ad4b9..5dde138763eb0 100644
--- a/drivers/media/i2c/ov5647.c
+++ b/drivers/media/i2c/ov5647.c
@@ -21,6 +21,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/io.h>
@@ -35,6 +36,13 @@
#define SENSOR_NAME "ov5647"
+/*
+ * From the datasheet, "20ms after PWDN goes low or 20ms after RESETB goes
+ * high if reset is inserted after PWDN goes high, host can access sensor's
+ * SCCB to initialize sensor."
+ */
+#define PWDN_ACTIVE_DELAY_MS 20
+
#define MIPI_CTRL00_CLOCK_LANE_GATE BIT(5)
#define MIPI_CTRL00_BUS_IDLE BIT(2)
#define MIPI_CTRL00_CLOCK_LANE_DISABLE BIT(0)
@@ -86,6 +94,7 @@ struct ov5647 {
unsigned int height;
int power_count;
struct clk *xclk;
+ struct gpio_desc *pwdn;
};
static inline struct ov5647 *to_state(struct v4l2_subdev *sd)
@@ -355,6 +364,11 @@ static int ov5647_sensor_power(struct v4l2_subdev *sd, int on)
if (on && !ov5647->power_count) {
dev_dbg(&client->dev, "OV5647 power on\n");
+ if (ov5647->pwdn) {
+ gpiod_set_value_cansleep(ov5647->pwdn, 0);
+ msleep(PWDN_ACTIVE_DELAY_MS);
+ }
+
ret = clk_prepare_enable(ov5647->xclk);
if (ret < 0) {
dev_err(&client->dev, "clk prepare enable failed\n");
@@ -392,6 +406,8 @@ static int ov5647_sensor_power(struct v4l2_subdev *sd, int on)
dev_dbg(&client->dev, "soft stby failed\n");
clk_disable_unprepare(ov5647->xclk);
+
+ gpiod_set_value_cansleep(ov5647->pwdn, 1);
}
/* Update the power count. */
@@ -581,6 +597,14 @@ static int ov5647_probe(struct i2c_client *client)
return -EINVAL;
}
+ /* Request the power down GPIO asserted */
+ sensor->pwdn = devm_gpiod_get_optional(&client->dev, "pwdn",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(sensor->pwdn)) {
+ dev_err(dev, "Failed to get 'pwdn' gpio\n");
+ return -EINVAL;
+ }
+
mutex_init(&sensor->lock);
sd = &sensor->sd;
@@ -594,7 +618,15 @@ static int ov5647_probe(struct i2c_client *client)
if (ret < 0)
goto mutex_remove;
+ if (sensor->pwdn) {
+ gpiod_set_value_cansleep(sensor->pwdn, 0);
+ msleep(PWDN_ACTIVE_DELAY_MS);
+ }
+
ret = ov5647_detect(sd);
+
+ gpiod_set_value_cansleep(sensor->pwdn, 1);
+
if (ret < 0)
goto error;
--
2.29.1
