On 02/11/2020 17:52, Jacopo Mondi wrote: > Hello, this v3 breaks out the support for bcm2835-unicam driver from: > "[PATCH v2 00/34] Drivers for the BCM283x CSI-2/CCP2 receiver and ISP" > https://lwn.net/Articles/819425/ > > The major changes can be summarized as: > - Rebase on most recent media master > - Move to staging > The unicam driver links to sensor drivers with 2 pads to transport the > sensor embedded data to a dedicated video device node. It also handles > communications with the sub-device and format negotiation by using the kAPI > provided by v4l2-subdev, but at the same exposes a media controller node. > There's a lenghty discussion involving Sakari, Laurent and Dave, and not to > block the driver upstreaming I've decided moving it to staging would make > the current implementation acceptable. > - Bump driver version to the current rpi-5.9.y branch > - Address comments from Hans and Sakari > - Use the dev_ logging infrastructure and replace custom printouts > - Rework endpoint parsing and registration > - Remove pm function wrappers > - Add V4L2_DEVICE_CAPS to capabilities in querycap() > - Remove some minor development leftovers and beautify debug messages > - Fix DTS warning on CSI-2 nodes: > ../arch/arm/boot/dts/bcm2711.dtsi:297.22-317.5: Warning (avoid_unnecessary_addr_size): /soc/csi@7e800000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property > ../arch/arm/boot/dts/bcm2711.dtsi:319.22-339.5: Warning (avoid_unnecessary_addr_size): /soc/csi@7e801000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property > > Note: > > In the patches upported from the 5.9.y branch the following is included > "media: bcm2835: unicam: Set VPU min clock freq to 250Mhz." > Which requires adding a second clock provider to the csi2 nodes in the DTS. > > Test: > > Tested with ov5647 (Pi Camera v1) capturing 10-bit SBGGR formats. > Capturing 8-bit SBGGR seems broken. Dave/Naush did am I mistaken or was this > a known issue on sensor side ? > > The usual v4l2-compliance log is below provided. For the next version, can you test with 'v4l2-compliance -s -f'? That tests streaming as well and also streaming for all supported formats. Regards, Hans > 1 test fails. The reson is reported in this comment block but I can't get > what the intended behaviour should be: > > /* > * If either CROPCAP or G_CROP works, then G_SELECTION should > * work as well. > * If neither CROPCAP nor G_CROP work, then G_SELECTION shouldn't > * work either. > */ > > -------------------------------------------------------------------------------- > v4l2-compliance 1.21.0-4679, 32 bits, 32-bit time_t > v4l2-compliance SHA: 225c6c2a17be 2020-10-30 15:13:07 > > Compliance test for unicam device /dev/video0: > > Driver Info: > Driver name : unicam > Card type : unicam > Bus info : platform:fe801000.csi > Driver version : 5.10.0 > Capabilities : 0x85a00001 > Video Capture > Metadata Capture > Read/Write > Streaming > Extended Pix Format > Device Capabilities > Device Caps : 0x05200001 > Video Capture > Read/Write > Streaming > Extended Pix Format > Media Driver Info: > Driver name : unicam > Model : unicam > Serial : > Bus info : platform:fe801000.csi > Media version : 5.10.0 > Hardware revision: 0x00000000 (0) > Driver version : 5.10.0 > Interface Info: > ID : 0x03000005 > Type : V4L Video > Entity Info: > ID : 0x00000003 (3) > Name : unicam-image > Function : V4L2 I/O > Flags : default > Pad 0x01000004 : 0: Sink > Link 0x02000007: from remote pad 0x1000002 of entity 'ov5647 10-0036': Data, Enabled, Immutable > > Required ioctls: > test MC information (see 'Media Driver Info' above): OK > test VIDIOC_QUERYCAP: OK > > Allow for multiple opens: > test second /dev/video0 open: OK > test VIDIOC_QUERYCAP: OK > test VIDIOC_G/S_PRIORITY: OK > test for unlimited opens: OK > > test invalid ioctls: OK > Debug ioctls: > test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) > test VIDIOC_LOG_STATUS: OK > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 1 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Control ioctls (Input 0): > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK > test VIDIOC_QUERYCTRL: OK > test VIDIOC_G/S_CTRL: OK > test VIDIOC_G/S/TRY_EXT_CTRLS: OK > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 12 Private Controls: 0 > > Format ioctls (Input 0): > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK > test VIDIOC_TRY_FMT: OK > test VIDIOC_S_FMT: OK > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > fail: v4l2-test-formats.cpp(1606): !doioctl(node, VIDIOC_G_SELECTION, &sel) > fail: v4l2-test-formats.cpp(1624): testLegacyCrop(node) > test Cropping: FAIL > test Composing: OK (Not Supported) > test Scaling: OK (Not Supported) > > Codec ioctls (Input 0): > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) > > Buffer ioctls (Input 0): > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK > test VIDIOC_EXPBUF: OK > test Requests: OK (Not Supported) > > Total for unicam device /dev/video0: 46, Succeeded: 45, Failed: 1, Warnings: 0 > -------------------------------------------------------------------------------- > > Dave Stevenson (1): > dt-bindings: media: Document BCM283x CSI2/CCP2 receiver > > Laurent Pinchart (1): > ARM: dts: bcm2711: Add Unicam DT nodes > > Naushir Patuck (3): > media: uapi: v4l2-core: Add sensor ancillary data V4L2 fourcc type > media: uapi: Add MEDIA_BUS_FMT_SENSOR_DATA media bus format > media: bcm2835-unicam: Driver for CCP2/CSI2 camera interface > > .../bindings/media/brcm,bcm2835-unicam.yaml | 155 + > .../userspace-api/media/v4l/meta-formats.rst | 1 + > .../media/v4l/pixfmt-meta-sensor-data.rst | 32 + > .../media/v4l/subdev-formats.rst | 32 + > MAINTAINERS | 7 + > arch/arm/boot/dts/bcm2711.dtsi | 45 + > drivers/media/v4l2-core/v4l2-ioctl.c | 1 + > drivers/staging/media/Kconfig | 2 + > drivers/staging/media/Makefile | 1 + > drivers/staging/media/bcm2835-unicam/Kconfig | 21 + > drivers/staging/media/bcm2835-unicam/Makefile | 3 + > .../media/bcm2835-unicam/bcm2835-unicam.c | 2800 +++++++++++++++++ > .../media/bcm2835-unicam/vc4-regs-unicam.h | 253 ++ > include/uapi/linux/media-bus-format.h | 3 + > include/uapi/linux/videodev2.h | 1 + > 15 files changed, 3357 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml > create mode 100644 Documentation/userspace-api/media/v4l/pixfmt-meta-sensor-data.rst > create mode 100644 drivers/staging/media/bcm2835-unicam/Kconfig > create mode 100644 drivers/staging/media/bcm2835-unicam/Makefile > create mode 100644 drivers/staging/media/bcm2835-unicam/bcm2835-unicam.c > create mode 100644 drivers/staging/media/bcm2835-unicam/vc4-regs-unicam.h > > -- > 2.29.1 >
