[PATCH v4 1/3] dt-bindings: ov2680: convert bindings to yaml

[Rui Miguel Silva <rmfrfs@xxxxxxxxx>]

Convert ov2680 sensor bindings documentation to yaml schema, remove
the textual bindings document and update MAINTAINERS entry.

Signed-off-by: Rui Miguel Silva <rmfrfs@xxxxxxxxx>
Reviewed-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
v3 -> v4:
  Rob Herring:
    https://lore.kernel.org/linux-media/20201019203910.GB3550266@bogus/
    - remove clock-names description
    - add maxItems to reset-gpios

 .../devicetree/bindings/media/i2c/ov2680.txt  | 46 ---------
 .../bindings/media/i2c/ovti,ov2680.yaml       | 99 +++++++++++++++++++
 MAINTAINERS                                   |  2 +-
 3 files changed, 100 insertions(+), 47 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov2680.txt
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
deleted file mode 100644
index 11e925ed9dad..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ov2680.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* Omnivision OV2680 MIPI CSI-2 sensor
-
-Required Properties:
-- compatible: should be "ovti,ov2680".
-- clocks: reference to the xvclk input clock.
-- clock-names: should be "xvclk".
-- DOVDD-supply: Digital I/O voltage supply.
-- DVDD-supply: Digital core voltage supply.
-- AVDD-supply: Analog voltage supply.
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
-               if any. This is an active low signal to the OV2680.
-
-The device node must contain one 'port' child node for its digital output
-video port, and this port must have a single endpoint in accordance with
- the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
-- data-lanes: should be set to <1> (one CSI-2 lane supported).
-
-Example:
-
-&i2c2 {
-	ov2680: camera-sensor@36 {
-		compatible = "ovti,ov2680";
-		reg = <0x36>;
-		clocks = <&osc>;
-		clock-names = "xvclk";
-		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
-		DOVDD-supply = <&sw2_reg>;
-		DVDD-supply = <&sw2_reg>;
-		AVDD-supply = <&reg_peri_3p15v>;
-
-		port {
-			ov2680_to_mipi: endpoint {
-				remote-endpoint = <&mipi_from_sensor>;
-				clock-lanes = <0>;
-				data-lanes = <1>;
-			};
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
new file mode 100644
index 000000000000..43bf749807e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV2680 CMOS Sensor
+
+maintainers:
+  - Rui Miguel Silva <rmfrfs@xxxxxxxxx>
+
+description: |-
+  The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2
+  megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200)
+  camera. It provides full-frame, sub-sampled, or windowed 10-bit images in
+  various formats via the control of the Serial Camera Control Bus (SCCB)
+  interface. The OV2680 has an image array capable of operating at up to 30
+  frames per second (fps) in UXGA resolution.
+
+properties:
+  compatible:
+    const: ovti,ov2680
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: xvclk
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls sensor reset.
+      This corresponds to the hardware pin XSHUTDOWN which is physically
+      active low.
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Definition of the regulator used as interface power supply.
+
+  avdd-supply:
+    description:
+      Definition of the regulator used as analog power supply.
+
+  dvdd-supply:
+    description:
+      Definition of the regulator used as digital power supply.
+
+  port:
+    type: object
+    description:
+      A node containing an output port node with an endpoint definition
+      as documented in
+      Documentation/devicetree/bindings/media/video-interfaces.txt
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - reset-gpios
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov2680: camera-sensor@36 {
+                compatible = "ovti,ov2680";
+                reg = <0x36>;
+                clocks = <&osc>;
+                clock-names = "xvclk";
+                reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+                dovdd-supply = <&sw2_reg>;
+                dvdd-supply = <&sw2_reg>;
+                avdd-supply = <&reg_peri_3p15v>;
+
+                port {
+                        ov2680_to_mipi: endpoint {
+                                remote-endpoint = <&mipi_from_sensor>;
+                        };
+                };
+        };
+    };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index f2757c6068e3..2cb2a5c60a1d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12781,7 +12781,7 @@ M:	Rui Miguel Silva <rmfrfs@xxxxxxxxx>
 L:	linux-media@xxxxxxxxxxxxxxx
 S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
-F:	Documentation/devicetree/bindings/media/i2c/ov2680.txt
+F:	Documentation/devicetree/bindings/media/i2c/ov2680.yaml
 F:	drivers/media/i2c/ov2680.c
 
 OMNIVISION OV2685 SENSOR DRIVER
-- 
2.28.0