Hi Jacopo,
On Mon, Aug 24, 2020 at 02:15:13PM +0200, Jacopo Mondi wrote:
> On Mon, Aug 24, 2020 at 02:34:40PM +0300, Laurent Pinchart wrote:
> > On Mon, Aug 24, 2020 at 10:32:11AM +0200, Jacopo Mondi wrote:
> > > On Wed, Aug 19, 2020 at 04:52:04PM +0300, Laurent Pinchart wrote:
> > > > On Tue, Aug 18, 2020 at 02:20:10PM +0200, Jacopo Mondi wrote:
> > > > > Convert the ov772x binding document to json-schema and update
> > > > > the MAINTAINERS file accordingly.
> > > > >
> > > > > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > > > > ---
> > > > > .../devicetree/bindings/media/i2c/ov772x.txt | 40 ---------
> > > > > .../devicetree/bindings/media/i2c/ov772x.yaml | 84 +++++++++++++++++++
> > > >
> > > > Could yuo rename this to ovti,ov772x.yaml ?
> > > >
> > > > > MAINTAINERS | 2 +-
> > > > > 3 files changed, 85 insertions(+), 41 deletions(-)
> > > > > delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov772x.txt
> > > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ov772x.yaml
> > > > >
> > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt
> > > > > deleted file mode 100644
> > > > > index 0b3ede5b8e6a..000000000000
> > > > > --- a/Documentation/devicetree/bindings/media/i2c/ov772x.txt
> > > > > +++ /dev/null
> > > > > @@ -1,40 +0,0 @@
> > > > > -* Omnivision OV7720/OV7725 CMOS sensor
> > > > > -
> > > > > -The Omnivision OV7720/OV7725 sensor supports multiple resolutions output,
> > > > > -such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can
> > > > > -support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats.
> > > > > -
> > > > > -Required Properties:
> > > > > -- compatible: shall be one of
> > > > > - "ovti,ov7720"
> > > > > - "ovti,ov7725"
> > > > > -- clocks: reference to the xclk input clock.
> > > > > -
> > > > > -Optional Properties:
> > > > > -- reset-gpios: reference to the GPIO connected to the RSTB pin which is
> > > > > - active low, if any.
> > > > > -- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is
> > > > > - active high, if any.
> > > > > -
> > > > > -The device node shall contain one 'port' child node with one child 'endpoint'
> > > > > -subnode for its digital output video port, in accordance with the video
> > > > > -interface bindings defined in Documentation/devicetree/bindings/media/
> > > > > -video-interfaces.txt.
> > > > > -
> > > > > -Example:
> > > > > -
> > > > > -&i2c0 {
> > > > > - ov772x: camera@21 {
> > > > > - compatible = "ovti,ov7725";
> > > > > - reg = <0x21>;
> > > > > - reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>;
> > > > > - powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>;
> > > > > - clocks = <&xclk>;
> > > > > -
> > > > > - port {
> > > > > - ov772x_0: endpoint {
> > > > > - remote-endpoint = <&vcap1_in0>;
> > > > > - };
> > > > > - };
> > > > > - };
> > > > > -};
> > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.yaml b/Documentation/devicetree/bindings/media/i2c/ov772x.yaml
> > > > > new file mode 100644
> > > > > index 000000000000..2b84fefeb4aa
> > > > > --- /dev/null
> > > > > +++ b/Documentation/devicetree/bindings/media/i2c/ov772x.yaml
> > > > > @@ -0,0 +1,84 @@
> > > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > > +%YAML 1.2
> > > > > +---
> > > > > +$id: http://devicetree.org/schemas/media/i2c/ov772x.yaml#
> > > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > > +
> > > > > +title: Omnivision OV7720/OV7725 CMOS sensor
> > > > > +
> > > > > +maintainers:
> > > > > + - Jacopo Mondi <jacopo@xxxxxxxxxx>
> > > > > +
> > > > > +description: -|
> > > > > + The Omnivision OV7720/OV7725 sensor supports multiple resolutions output,
> > > > > + such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can
> > > > > + support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats.
> > > > > +
> > > > > +properties:
> > > > > + compatible:
> > > > > + enum:
> > > > > + - ovti,ov7720
> > > > > + - ovti,ov7725
> > > > > +
> > > > > + reg:
> > > > > + maxItems: 1
> > > > > +
> > > > > + clocks:
> > > > > + maxItems: 1
> > > > > +
> > > > > + reset-gpios:
> > > > > + description: -|
> > > > > + Reference to the GPIO connected to the RSTB pin which is active low.
> > > > > + maxItems: 1
> > > > > +
> > > > > + powerdown-gpios:
> > > > > + description: -|
> > > > > + Reference to the GPIO connected to the PWDN pin which is active high.
> > > > > + maxItems: 1
> > > > > +
> > > > > + port:
> > > > > + type: object
> > > > > + description: |
> > > > > + The device node must contain one 'port' child node for its digital output
> > > > > + video port, in accordance with the video interface bindings defined in
> > > > > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > > >
> > > > You can simply write
> > > >
> > > > Digital input video port. See ../video-interfaces.txt.
> > > >
> > > > > +
> > > > > + properties:
> > > > > + endpoint:
> > > > > + type: object
> > > > > + properties:
> > > > > + remote-endpoint:
> > > > > + description: A phandle to the bus receiver's endpoint node.
> > > >
> > > > required:
> > > > - remote-endpoint
> > > >
> > > > additionalProperties: false
> > >
> > > I receveied a reply to you on previous json-schema conversion attempt
> > > where you suggested to not set remote-endpoint as required, as we
> > > allow empty ones to be later filled in in, maybe with an overlay.
> > >
> > > Which Laurent should I listen to ? I tend to agree with the one that
> > > said to drop remote-endpoint from the required properties list.
> >
> > Maybe I recall incorrectly, didn't I say that endpoint shouldn't be
> > mandatory ? Ports should be mandatory as they describe the hardware,
> > endpoints describe a connection, and within a connection, I'm not sure
> > to see a use-case for not setting remote-endpoint. Maybe I need to look
> > better ? :-)
> >
>
> I might be confused as well, but to me port and endpoint should be
> there as they represent the available endpoints of the devices connections.
> Connections to external devices that can be established (or overwritten)
> by applying an overlay, and such are not mandatory.
>
> As I see it:
> - port/endpoints: establish the available device connection endpoitns
> and shall be mandatory (also to give a known place where to 'plug'
> the connections)
>
> - remote-endpoints: data connections to external devices, which might
> depend on the board assembly or installed 'capes' and expansions. As
> such, they can be modeled as an overlay fragment to be applied on the
> (known layout of the) device.
Only the port represents a connection point. The endpoint node is part
of the representation of the link, it doesn't map to a particular
hardware resource on the port side.
> > > > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > > >
> > > > > +
> > > > > + additionalProperties: false
> > > > > +
> > > > > +required:
> > > > > + - compatible
> > > > > + - reg
> > > > > + - clocks
> > > > > + - reset-gpios
> > > > > + - powerdown-gpios
> > > > > +
> > > > > +examples:
> > > > > + - |
> > > > > + #include <dt-bindings/gpio/gpio.h>
> > > > > +
> > > > > + i2c0 {
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <0>;
> > > > > + ov772x: camera@21 {
> > > > > + compatible = "ovti,ov7725";
> > > > > + reg = <0x21>;
> > > > > + reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>;
> > > > > + powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>;
> > > > > + clocks = <&xclk>;
> > > > > +
> > > > > + port {
> > > > > + ov772x_0: endpoint {
> > > > > + remote-endpoint = <&vcap1_in0>;
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > +
> > > > > +...
> > > > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > > > index d1a6173d3b64..d0a20214eaaf 100644
> > > > > --- a/MAINTAINERS
> > > > > +++ b/MAINTAINERS
> > > > > @@ -12666,7 +12666,7 @@ M: Jacopo Mondi <jacopo@xxxxxxxxxx>
> > > > > L: linux-media@xxxxxxxxxxxxxxx
> > > > > S: Odd fixes
> > > > > T: git git://linuxtv.org/media_tree.git
> > > > > -F: Documentation/devicetree/bindings/media/i2c/ov772x.txt
> > > > > +F: Documentation/devicetree/bindings/media/i2c/ov772x.yaml
> > > > > F: drivers/media/i2c/ov772x.c
> > > > > F: include/media/i2c/ov772x.h
> > > > >
--
Regards,
Laurent Pinchart
