Hi Prabhakar,
On Wed, Aug 5, 2020 at 10:01 AM Lad, Prabhakar
<prabhakar.csengg@xxxxxxxxx> wrote:
> On Tue, Aug 4, 2020 at 4:32 PM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
> > On Tue, Aug 4, 2020 at 5:12 PM Lad, Prabhakar
> > <prabhakar.csengg@xxxxxxxxx> wrote:
> > > On Tue, Aug 4, 2020 at 11:17 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
> > > > On Tue, Aug 4, 2020 at 12:05 PM Niklas <niklas.soderlund@xxxxxxxxxxxx> wrote:
> > > > > On 2020-08-04 09:04:25 +0100, Lad, Prabhakar wrote:
> > > > > > On Mon, Aug 3, 2020 at 8:28 PM Niklas <niklas.soderlund@xxxxxxxxxxxx> wrote:
> > > > > > > On 2020-08-03 20:17:54 +0100, Lad, Prabhakar wrote:
> > > > > > > > On Mon, Aug 3, 2020 at 7:06 PM Niklas <niklas.soderlund@xxxxxxxxxxxx> wrote:
> > > > > > > > > On 2020-08-03 17:02:53 +0100, Lad Prabhakar wrote:
> > > > > > > > > > Select the data pins for YCbCr422-8bit input format depending on
> > > > > > > > > > bus_width and data_shift passed as part of DT.
> > > > > > > > > >
> > > > > > > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > > > > > > > > > Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > > >
> > > > > > > > > > --- a/drivers/media/platform/rcar-vin/rcar-core.c
> > > > > > > > > > +++ b/drivers/media/platform/rcar-vin/rcar-core.c
> > > > > > > > > > @@ -624,6 +624,11 @@ static int rvin_parallel_parse_v4l2(struct device *dev,
> > > > > > > > > > vin->parallel = rvpe;
> > > > > > > > > > vin->parallel->mbus_type = vep->bus_type;
> > > > > > > > > >
> > > > > > > > > > + /* select VInDATA[15:8] pins for YCbCr422-8bit format */
> > > > > > > > > > + if (vep->bus.parallel.bus_width == BUS_WIDTH_8 &&
> > > > > > > > > > + vep->bus.parallel.data_shift == DATA_SHIFT_8)
> > > > > > > > > > + vin->parallel->ycbcr_8b_g = true;
> > > > > > > > > > +
> > > > > > > > >
> > > > > > > > > I would store the bus_width and bus_shift values in the struct
> > > > > > > > > rvin_parallel_entity and evaluate them in place rater then create a flag
> > > > > > > > > for this specific use-case..
> > > > > > > > >
> > > > > > > > Ok will do that.
> > > > > > > >
> > > > > > > > > Also according to the documentation is the check correct? Do we not wish
> > > > > > > > > to use the new mode when bus_width == 16 and bus_shift == 8. The check
> > > > > > > > > you have here seems to describe a 8 lane bus where 0 lanes are used.
> > > > > > > > >
> > > > > > > > bus-width is the actual data lines used, so bus_width == 16 and
> > > > > > > > bus_shift == 8 would mean use lines 23:8, so just check for bus_width
> > > > > > > > == 8 and bus_shift == 8 should be sufficient.
> > > > > > >
> > > > > > > As you and Geert points out I was wrong, they should indeed both be 8.
> > > > > > >
> > > > > > > >
> > > > > > > > > I think you should also verify that bus_shift is either 0 or 8 as that
> > > > > > > > > is all the driver supports.
> > > > > > > > >
> > > > > > > > Not sure if thats correct.In that case this patch wont make sense, I
> > > > > > > > believed we agreed upon we determine the YDS depending on both
> > > > > > > > bus-width and bus-shift.
> > > > > > >
> > > > > > > I'm sorry I think I lost you :-) The driver is not capable of supporting
> > > > > > > bus_width = 8 and bus_shift = 2 right? Maybe we are talking about
> > > > > > > different things.
> > > > > > >
> > > > > > > What I tried to say (updated with the knowledge of that bus_width should
> > > > > > > indeed be 8 and not 16) was that would it make sens to with bus_width=8
> > > > > > > allow for a bus_shift value other then 0 or 8? What for example would
> > > > > > > the driver do if the value was 2?
> > > > > > >
> > > > > > I think this should be possible but I am not sure how this will work.
> > > > > > For example on iWave G21D-Q7 platform with 16-bit wired bus say we
> > > > > > connect a 8-bit camera as below:
> > > > > >
> > > > > > bus-width = 8 and bus-shift = 2
> > > > > > VI1_G0_B -> Not connected
> > > > > > VI1_G1_B -> Not connected
> > > > > > VI1_G2_B_16 -> Connected
> > > > > > VI1_G3_B -> Connected
> > > > > > VI1_G4_B -> Connected
> > > > > > VI1_G5_B -> Connected
> > > > > > VI1_G6_B -> Connected
> > > > > > VI1_G7_B -> Connected
> > > > > > VI1_DATA7_B/VI1_B7_B_16 -> Connected
> > > > > > VI1_DATA6_B/VI1_B6_B_16 -> Connected
> > > > > > VI1_DATA5_B/VI1_B5_B_16 -> Not connected
> > > > > > VI1_DATA4_B/VI1_B4_B_16 -> Not connected
> > > > > > VI1_DATA3_B/VI1_B3_B_16 -> Not connected
> > > > > > VI1_DATA2_B/VI1_B2_B_16 -> Not connected
> > > > > > VI1_DATA1_B/VI1_B1_B_16 -> Not connected
> > > > > > VI1_DATA0_B/VI1_B0_B_16 -> Not connected
> > > > >
> > > > > I agree this is how I would imagine bus-width = 8 and bus-shift = 2 to
> > > > > be wired.
> > > > >
> > > > > > So in this case for 8-bit YCbCr422 format should YDS be set I am not
> > > > > > sure. Or is this not a valid case at all ?
> > > > >
> > > > > That is my question :-)
> > > > >
> > > > > I can't find anything int the documentation that would allow is to do
> > > > > anything other then bus-width = 8 together with bus-shift = 0 (do not
> > > > > set YDS) or bus-shift = 8 (set YDS). So that is why I suggested you
> > > > > check for this and print a warning if bus-shift is anything else :-)
> > > > >
> > > > > But if you can figured out how we can do a bus-shift = 2 as in your
> > > > > example then of course the check is wrong. I have not read the docs
> > > > > carefully enough about this to rule it out as impossible.
> > > >
> > > > IIUIC, this is a completely different scenario than "low" or "high" wiring
> > > > of 8-bit YCbCr-422, hence YDS does not apply?
> > > >
> > > I tend to agree. We only enable YDS if bus-width = 8 and bus-shift=8
> > > as done by this patch. (Although there isn't enough documentation to
> > > prove it)
> > >
> > > > The iWave G21D-Q7 wiring seems to be 10-bit YCbCr-422 with the 2 LSB
> > > > bits unconnected?
> > > >
> > > B-8bit/ BG-16 bit for VI0 and B-8bit/ BG-16 bit for VI0
> > >
> > > > Interestingly, that mode is supported on all RZ/G1 SoCs, on most R-Car
> > > > Gen3 SoCs, but only on a single R-Car Gen2 SoC (V2H).
> > > >
> > > YDS mode ?
> >
> > No, 10-bit YCbCr-422. But please forget my comment, I was looking at
> > the wrong table.
> >
> > VI1_G[7:2] plus VI1_DATA[7:6] is not even a contiguous subset (I had
> > misread the used subset to be G[1:0] and B[7:2]), so it cannot be represented
> > using just bus-width and bus-shift properties?
> >
> Yes and here is my explanation.
>
> In Gen1 manual for YDS bit it says the below:
> 0: Vin_B[7:0] pins
> 1: Vin_G[7:0] pins
>
> And in Gen2 manual it says,
> 0: Vin_DATA[7:0] pins
> 1: Vin_DATA[7:0] pins
Vin_DATA[15:8]
The difference is due to some SoCs naming the signals R[7:0], G[7:0], B[7:0],
while other SoCs use DATA[23:0], the latter presumably to avoid
confusion when using non-RGB input formats.
R-Car V2H uses a mix: D[23:16]_R[7:0], D[15:8]_G[7:0], D[7:0]_B[7:0] ;-)
However, the underlying behavior is the same, which is clear from the
RGB-666 mode, which is not using contiguous DATA[17:0], but sparse
DATA[23:18], DATA[15:10], DATA[7:2], i.e. the 6 MSB of each color
component.
> On iwave platform for the VIN2 interface the following G pins are connected:
>
> VI2_G0_MARK, VI2_G1_MARK,
> VI2_G2_MARK, VI2_G3_MARK,
> VI2_G4_MARK, VI2_G5_MARK,
> VI2_G6_MARK, VI2_G7_MARK,
>
> And for capture to work on this interface the YDS bit has to be set.
>
> Now suppose some day we have a platform with 16 bit interface where G
> and R pins are connected:
>
> VI2_G0_MARK, VI2_G1_MARK,
> VI2_G2_MARK, VI2_G3_MARK,
> VI2_G4_MARK, VI2_G5_MARK,
> VI2_G6_MARK, VI2_G7_MARK,
> /* R */
> VI2_R0_MARK, VI2_R1_MARK,
> VI2_R2_MARK, VI2_R3_MARK,
> VI2_R4_MARK, VI2_R5_MARK,
> VI2_R6_MARK, VI2_R7_MARK,
>
> Scenarios
> 1: Say we connect a 8-bit camera just with the G pins - YDS has to be
> 1 for 8-bit YCbCr
> 2: Say we connect a 8-bit camera just with the R pins - YDS has to be
> 0 for 8-bit YCbCr
> 3: Now say we use G2-G7 along with R0 and R1 pins to connect a 8 bit
> camera - YDS has to be 1 for 8-bit camera
>
> And looking at the Gen1 description of YDS bit, having a combination
> of B and G is not a valid case.
Scenario 3 is indeed not supported. But G[1:0] and B[7:2] (= DATA[9:2])
could work when using 10-bit YCbCr.
> So my vote is to have a property in the endpoint to say if YDS has to
> be enabled as done in my first version of the patch.
"YDS" is not a generic property, "data-shift" is.
Now, how do you specify in DT that RGB-666 mode is to be used?
"bus-width = <18>"?
That won't work with the (so far theoretical) case where both contiguous
and sparse variants are supported by the hardware. And "data-shift"
won't help here.
Am I overdesigning? ;-)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
