Use the new get_mbus_config and set_mbus_config pad operations in place
of the video operations currently in use.
Compared to other drivers where the same conversion has been performed,
ov6650 proved to be a bit more tricky, as the existing g_mbus_config
implementation did not report the currently applied configuration but
the set of all possible configuration options.
Adapt the driver to support the semantic of the two newly introduced
operations:
- get_mbus_config reports the current media bus configuration
- set_mbus_config applies only changes explicitly requested and updates
the provided cfg parameter to report what has actually been applied to
the hardware.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
v8 -> v8.1
- Return error on register write fails in set_mbus_config() as suggested
by Janusz.
---
drivers/media/i2c/ov6650.c | 53 ++++++++++++++++++++++++++------------
1 file changed, 37 insertions(+), 16 deletions(-)
diff --git a/drivers/media/i2c/ov6650.c b/drivers/media/i2c/ov6650.c
index 91906b94f978..48493af81198 100644
--- a/drivers/media/i2c/ov6650.c
+++ b/drivers/media/i2c/ov6650.c
@@ -921,55 +921,74 @@ static const struct v4l2_subdev_core_ops ov6650_core_ops = {
};
/* Request bus settings on camera side */
-static int ov6650_g_mbus_config(struct v4l2_subdev *sd,
- struct v4l2_mbus_config *cfg)
+static int ov6650_get_mbus_config(struct v4l2_subdev *sd,
+ unsigned int pad,
+ struct v4l2_mbus_config *cfg)
{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ u8 comj, comf;
+ int ret;
+
+ ret = ov6650_reg_read(client, REG_COMJ, &comj);
+ if (ret)
+ return ret;
- cfg->flags = V4L2_MBUS_MASTER |
- V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_PCLK_SAMPLE_FALLING |
- V4L2_MBUS_HSYNC_ACTIVE_HIGH | V4L2_MBUS_HSYNC_ACTIVE_LOW |
- V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_VSYNC_ACTIVE_LOW |
- V4L2_MBUS_DATA_ACTIVE_HIGH;
+ ret = ov6650_reg_read(client, REG_COMF, &comf);
+ if (ret)
+ return ret;
+
+ cfg->flags = V4L2_MBUS_MASTER | V4L2_MBUS_DATA_ACTIVE_HIGH
+ | ((comj & COMJ_VSYNC_HIGH) ? V4L2_MBUS_VSYNC_ACTIVE_HIGH
+ : V4L2_MBUS_VSYNC_ACTIVE_LOW)
+ | ((comf & COMF_HREF_LOW) ? V4L2_MBUS_HSYNC_ACTIVE_LOW
+ : V4L2_MBUS_HSYNC_ACTIVE_HIGH)
+ | ((comj & COMJ_PCLK_RISING) ? V4L2_MBUS_PCLK_SAMPLE_RISING
+ : V4L2_MBUS_PCLK_SAMPLE_FALLING);
cfg->type = V4L2_MBUS_PARALLEL;
return 0;
}
/* Alter bus settings on camera side */
-static int ov6650_s_mbus_config(struct v4l2_subdev *sd,
- const struct v4l2_mbus_config *cfg)
+static int ov6650_set_mbus_config(struct v4l2_subdev *sd,
+ unsigned int pad,
+ struct v4l2_mbus_config *cfg)
{
struct i2c_client *client = v4l2_get_subdevdata(sd);
- int ret;
+ int ret = 0;
if (cfg->flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
ret = ov6650_reg_rmw(client, REG_COMJ, COMJ_PCLK_RISING, 0);
- else
+ else if (cfg->flags & V4L2_MBUS_PCLK_SAMPLE_FALLING)
ret = ov6650_reg_rmw(client, REG_COMJ, 0, COMJ_PCLK_RISING);
if (ret)
return ret;
if (cfg->flags & V4L2_MBUS_HSYNC_ACTIVE_LOW)
ret = ov6650_reg_rmw(client, REG_COMF, COMF_HREF_LOW, 0);
- else
+ else if (cfg->flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
ret = ov6650_reg_rmw(client, REG_COMF, 0, COMF_HREF_LOW);
if (ret)
return ret;
if (cfg->flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH)
ret = ov6650_reg_rmw(client, REG_COMJ, COMJ_VSYNC_HIGH, 0);
- else
+ else if (cfg->flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
ret = ov6650_reg_rmw(client, REG_COMJ, 0, COMJ_VSYNC_HIGH);
+ if (ret)
+ return ret;
- return ret;
+ /*
+ * Update the configuration to report what is actually applied to
+ * the hardware.
+ */
+ return ov6650_get_mbus_config(sd, pad, cfg);
}
static const struct v4l2_subdev_video_ops ov6650_video_ops = {
.s_stream = ov6650_s_stream,
.g_frame_interval = ov6650_g_frame_interval,
.s_frame_interval = ov6650_s_frame_interval,
- .g_mbus_config = ov6650_g_mbus_config,
- .s_mbus_config = ov6650_s_mbus_config,
};
static const struct v4l2_subdev_pad_ops ov6650_pad_ops = {
@@ -978,6 +997,8 @@ static const struct v4l2_subdev_pad_ops ov6650_pad_ops = {
.set_selection = ov6650_set_selection,
.get_fmt = ov6650_get_fmt,
.set_fmt = ov6650_set_fmt,
+ .get_mbus_config = ov6650_get_mbus_config,
+ .set_mbus_config = ov6650_set_mbus_config,
};
static const struct v4l2_subdev_ops ov6650_subdev_ops = {
--
2.27.0
