Re: [RFC PATCH v2 00/18] Support for Tegra video capture from external sensor

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 6/30/20 2:21 AM, Hans Verkuil wrote:
On 17/06/2020 03:41, Sowjanya Komatineni wrote:
This series adds support for video capture from external camera sensor to
Tegra video driver.

Jetson TX1 has camera expansion connector and supports custom camera module
designed as per TX1 design specification.

This series also enables camera capture support for Jetson Nano which has
Raspberry PI camera header.

This series is tested with IMX219 camera sensor.
Which tree did you base this on? The media_tree master? Or the mainline kernel?
These patches are with linux-next base at the time I sent them out which are on 20200616

I now have the imx219 detected, but if I try to stream I get this:

$ v4l2-ctl --stream-mmap
<[  512.840944] video4linux video0: MW_ACK_DONE syncpt timeout: -11
[  512.972975] video4linux video0: frame start syncpt timeout: -11
<VIDIOC_DQBUF: failed: Input/output error
[  513.180770] video4linux video0: MW_ACK_DONE syncpt timeout: -11

And then everything hangs and I need to reset.

I'm testing with the media_tree master with your patches on top.

Regards,

	Hans

Are you using same device tree as I sent offline? It uses CSI A for IMX219.

Does you setup also uses CSI-A as x2 for IMX219?

I tested them on Jetson Nano + IMX219 rasp PI module and also on Jetson TX1 + IMX274.

I did not see any issue and am able to capture from both.

Will try again on my side with today's latest linux-next and update result.


This series include,

VI I2C related fixes
- Camera sensor programming happens through VI I2C which is on host1x bus.
- These patches includes device tree and I2C driver fixes for VI I2C.

Tegra video driver updates
- TPG Vs Non-TPG based on Kconfig
- Support for external sensor video capture based on device graph from DT.
- Support for selection ioctl operations
- Tegra MIPI CSI pads calibration
- CSI T-CLK and T-HS settle time computation based on clock rates.

Host1x driver updates
- Adds API to allow creating mipi device for specific device node.
- Splits MIPI pads calibrate start and waiting for calibration to be done.

Device tree updates
- Adds camera connector 2V8, 1V8, 1V2 regulator supplies to Jetson TX1 DT.
- Enabled VI and CSI support in Jetson Nano DT.


Delta between patch versions:

[v2]:	Includes below changes based on v1 feedback
	- dt-binding document and the driver update for device graph to use
	  separate ports for sink endpoint and source endpoint for csi.
	- Use data-lanes endpoint property for csi.
	- Update tegra_mipi_request() to take device node pointer argument
	  rather than adding extra API.
	- Remove checking for clk pointer before clk_disable.


Sowjanya Komatineni (18):
   dt-bindings: i2c: tegra: Document Tegra210 VI I2C clocks and
     power-domains
   arm64: tegra: Add missing clocks and power-domains to Tegra210 VI I2C
   i2c: tegra: Don't mark VI I2C as IRQ safe runtime PM
   i2c: tegra: Fix the error path in tegra_i2c_runtime_resume
   i2c: tegra: Fix runtime resume to re-init VI I2C
   i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c
   media: tegra-video: Fix channel format alignment
   media: tegra-video: Enable TPG based on kernel config
   media: tegra-video: Update format lookup to offset based
   dt-bindings: tegra: Update VI and CSI bindings with port info
   media: tegra-video: Add support for external sensor capture
   media: tegra-video: Add support for selection ioctl ops
   gpu: host1x: mipi: Update tegra_mipi_request() to be node based
   gpu: host1x: mipi: Split tegra_mipi_calibrate and tegra_mipi_wait
   media: tegra-video: Add CSI MIPI pads calibration
   media: tegra-video: Compute settle times based on the clock rate
   arm64: tegra: jetson-tx1: Add camera supplies
   arm64: tegra: Enable Tegra VI CSI support for Jetson Nano

  .../display/tegra/nvidia,tegra20-host1x.txt        |  92 ++-
  .../devicetree/bindings/i2c/nvidia,tegra20-i2c.txt |  19 +-
  arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi     |  41 ++
  arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts |  10 +
  arch/arm64/boot/dts/nvidia/tegra210.dtsi           |   6 +
  drivers/gpu/drm/tegra/dsi.c                        |   9 +-
  drivers/gpu/host1x/mipi.c                          |  30 +-
  drivers/i2c/busses/i2c-tegra.c                     |  39 +-
  drivers/staging/media/tegra-video/Kconfig          |   7 +
  drivers/staging/media/tegra-video/csi.c            | 245 ++++++-
  drivers/staging/media/tegra-video/csi.h            |   8 +
  drivers/staging/media/tegra-video/tegra210.c       |  25 +-
  drivers/staging/media/tegra-video/vi.c             | 770 +++++++++++++++++++--
  drivers/staging/media/tegra-video/vi.h             |  23 +-
  drivers/staging/media/tegra-video/video.c          |  23 +-
  include/linux/host1x.h                             |   4 +-
  16 files changed, 1251 insertions(+), 100 deletions(-)




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux