[PATCH v5 01/10] media: v4l2-subdev: Introduce [get|set]_mbus_config pad ops

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Introduce two new pad operations to allow retrieving and configuring the
media bus parameters on a subdevice pad.

The newly introduced operations aims to replace the s/g_mbus_config video
operations, which have been on their way for deprecation since a long
time.

Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
 include/media/v4l2-subdev.h | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index f7fe78a6f65a..d8b9d5735307 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -670,6 +670,29 @@ struct v4l2_subdev_pad_config {
  *
  * @set_frame_desc: set the low level media bus frame parameters, @fd array
  *                  may be adjusted by the subdev driver to device capabilities.
+ *
+ * @get_mbus_config: get the media bus configuration of a remote sub-device.
+ *		     The media bus configuration is usually retrieved from the
+ *		     firmware interface at sub-device probe time, immediately
+ *		     applied to the hardware and eventually adjusted by the
+ *		     driver. Remote sub-devices (usually video receivers) shall
+ *		     use this operation to query the transmitting end bus
+ *		     configuration in order to adjust their own one accordingly.
+ *		     Callers should make sure they get the most up-to-date as
+ *		     possible configuration from the remote end, likely calling
+ *		     this operation as close as possible to stream on time. The
+ *		     operation shall fail if the pad index it has been called on
+ *		     is not valid.
+ *
+ * @set_mbus_config: set the media bus configuration of a remote sub-device.
+ *		     This operations is intended to allow, in combination with
+ *		     the get_mbus_config operation, the negotiation of media bus
+ *		     configuration parameters between media sub-devices. The
+ *		     operation shall not fail if the requested configuration is
+ *		     not supported, but the driver shall update the content of
+ *		     the %config argument to reflect what has been actually
+ *		     applied to the hardware. The operation shall fail if the
+ *		     pad index it has been called on is not valid.
  */
 struct v4l2_subdev_pad_ops {
 	int (*init_cfg)(struct v4l2_subdev *sd,
@@ -710,6 +733,10 @@ struct v4l2_subdev_pad_ops {
 			      struct v4l2_mbus_frame_desc *fd);
 	int (*set_frame_desc)(struct v4l2_subdev *sd, unsigned int pad,
 			      struct v4l2_mbus_frame_desc *fd);
+	int (*get_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+			       struct v4l2_mbus_config *config);
+	int (*set_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+			       struct v4l2_mbus_config *config);
 };
 
 /**
-- 
2.27.0




[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux