Hi Marco,
On Thu, Apr 30, 2020 at 11:53:32AM +0200, Marco Felsch wrote:
> Hi Sakari,
>
> On 20-04-30 12:45, Sakari Ailus wrote:
> > Hi Marco,
> >
> > On Thu, Apr 30, 2020 at 11:35:24AM +0200, Marco Felsch wrote:
> > > Hi Robert,
> > >
> > > thnakf for the patch but pls keep in mind to do one thing per patch.
> > > IMHO this patch do a lot more. Anyway below are my comment :)
> > >
> > > On 20-04-29 18:24, Robert Foss wrote:
> > > > Add match table, enable ov8856_probe() to support
> > > > both ACPI and DT modes.
> > >
> > > You are also adding the support for reset-gpios and regualtors. IMHO the
> > > commit message don't belong to the changes you made anymore.
> > >
> > > > ACPI and DT modes are primarily distinguished from
> > > > each other by relying on devm_XXX_get_optional()
> > > > will return NULL instead of a reference for the
> > > > desired managed resource.
> > > >
> > > > Signed-off-by: Robert Foss <robert.foss@xxxxxxxxxx>
> > > > ---
> > > >
> > > > - Changes since v5:
> > > > * Maxime & Sakari: Replaced clock tolerance check with warning
> > > >
> > > > - Changes since v4:
> > > > * Maxime & Sakari: Switch to clock-frequency
> > > >
> > > > - Changes since v3:
> > > > * Remove redundant {}-brackets
> > > > * Compare xvclk_rate to 5% tolerance
> > > > * Andy: Use dev_fwnode()
> > > > * Andy: Use %pe instead of %ld + PTR_ERR()
> > > > * Andy: Invert reset_gpio logic
> > > > * Andy: Remove dev_dbg() from failing reset_gpio setup
> > > > * Andy: Use dev_err for logging for failures
> > > > * Andy: Remove dev_warn from EDEFER/regulator error path
> > > > * Andy & Sakari: Replaced GPIOD_OUT_XXX with 0/1
> > > > * Maxime & Sakari: Verify clock frequency from DT
> > > > * Sakari: Verify the 'xvclk_rate' is set correctly for ACPI/DT devices
> > > > * Sakari: Remove duplicate ov8856->dev assignment
> > > >
> > > > - Changes since v2:
> > > > * Added "struct device *dev" member to struct ov8856
> > > > * Andy: Switch to optional version of devm_gpiod_get
> > > > * Andy: Switch to optional version of devm_clk_get
> > > > * Fabio: Add reset sleep period
> > > > * Sakari: Unify defines for 19.2Mhz
> > > > * Sakari: Remove 24Mhz clock, since it isn't needed for supported modes
> > > > * Sakari: Replace dev_info() with dev_dbg()
> > > > * Sakari: Switch induction variable type to unsigned
> > > > * Sakari: Don't wait for reset_gpio when in ACPI mode
> > > > * Sakari: Pull reset GPIO high on power on failure
> > > > * Sakari: Add power on/off to resume/suspend
> > > > * Sakari: Fix indentation
> > > > * Sakari: Power off during ov8856_remove()
> > > > * Sakari: Don't sleep during power-on in ACPI mode
> > > > * Sakari: Switch to getting xvclk from clk_get_rate
> > > >
> > > > - Changes since v1:
> > > > * Andy & Sakari: Make XVCLK optional since to not break ACPI
> > > > * Fabio: Change n_shutdown_gpio name to reset_gpio
> > > > * Fabio: Invert reset_gpio due to GPIO_ACTIVE_HIGH -> GPIO_ACTIVE_LOW change
> > > > * Fabio: Remove empty line
> > > > * Fabio: Remove real error from devm_gpiod_get() failures
> > > > * Sakari: ARRAY_SIZE() directly instead of through OV8856_NUM_SUPPLIES
> > > > * Sakari: Use XVCLK rate as provided by DT
> > > >
> > > > drivers/media/i2c/ov8856.c | 137 +++++++++++++++++++++++++++++++++----
> > > > 1 file changed, 123 insertions(+), 14 deletions(-)
> > > >
> > > > diff --git a/drivers/media/i2c/ov8856.c b/drivers/media/i2c/ov8856.c
> > > > index 8655842af275..4749dc74d5ad 100644
> > > > --- a/drivers/media/i2c/ov8856.c
> > > > +++ b/drivers/media/i2c/ov8856.c
> > > > @@ -3,10 +3,13 @@
> > > >
> > > > #include <asm/unaligned.h>
> > > > #include <linux/acpi.h>
> > > > +#include <linux/clk.h>
> > > > #include <linux/delay.h>
> > > > +#include <linux/gpio/consumer.h>
> > > > #include <linux/i2c.h>
> > > > #include <linux/module.h>
> > > > #include <linux/pm_runtime.h>
> > > > +#include <linux/regulator/consumer.h>
> > > > #include <media/v4l2-ctrls.h>
> > > > #include <media/v4l2-device.h>
> > > > #include <media/v4l2-fwnode.h>
> > > > @@ -18,7 +21,7 @@
> > > > #define OV8856_LINK_FREQ_360MHZ 360000000ULL
> > > > #define OV8856_LINK_FREQ_180MHZ 180000000ULL
> > > > #define OV8856_SCLK 144000000ULL
> > > > -#define OV8856_MCLK 19200000
> > > > +#define OV8856_XVCLK_19_2 19200000
> > > > #define OV8856_DATA_LANES 4
> > > > #define OV8856_RGB_DEPTH 10
> > > >
> > > > @@ -64,6 +67,12 @@
> > > >
> > > > #define to_ov8856(_sd) container_of(_sd, struct ov8856, sd)
> > > >
> > > > +static const char * const ov8856_supply_names[] = {
> > > > + "dovdd", /* Digital I/O power */
> > > > + "avdd", /* Analog power */
> > > > + "dvdd", /* Digital core power */
> > > > +};
> > > > +
> > > > enum {
> > > > OV8856_LINK_FREQ_720MBPS,
> > > > OV8856_LINK_FREQ_360MBPS,
> > > > @@ -566,6 +575,11 @@ struct ov8856 {
> > > > struct media_pad pad;
> > > > struct v4l2_ctrl_handler ctrl_handler;
> > > >
> > > > + struct device *dev;
> > > > + struct clk *xvclk;
> > > > + struct gpio_desc *reset_gpio;
> > > > + struct regulator_bulk_data supplies[ARRAY_SIZE(ov8856_supply_names)];
> > > > +
> > > > /* V4L2 Controls */
> > > > struct v4l2_ctrl *link_freq;
> > > > struct v4l2_ctrl *pixel_rate;
> > > > @@ -908,6 +922,52 @@ static int ov8856_set_stream(struct v4l2_subdev *sd, int enable)
> > > > return ret;
> > > > }
> > > >
> > > > +static int __ov8856_power_on(struct ov8856 *ov8856)
> > > > +{
> > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
> > > > + int ret;
> > > > +
> > > > + ret = clk_prepare_enable(ov8856->xvclk);
> > >
> > > You're request the clk only in DT case or do I miss something? If so you
> > > have to check if the clk is available.
> > >
> > > > + if (ret < 0) {
> > > > + dev_err(&client->dev, "failed to enable xvclk\n");
> > > > + return ret;
> > > > + }
> > > > +
> > > > + if (is_acpi_node(dev_fwnode(ov8856->dev)))
> > > > + return 0;
> > > > +
> > > > + if (ov8856->reset_gpio) {
> > > > + gpiod_set_value_cansleep(ov8856->reset_gpio, 1);
> > > > + usleep_range(1000, 2000);
> > > > + }
> > > > +
> > > > + ret = regulator_bulk_enable(ARRAY_SIZE(ov8856_supply_names),
> > > > + ov8856->supplies);
> > > > + if (ret < 0) {
> > > > + dev_err(&client->dev, "failed to enable regulators\n");
> > > > + goto disable_clk;
> > > > + }
> > > > +
> > > > + gpiod_set_value_cansleep(ov8856->reset_gpio, 0);
> > >
> > > You need to check the existance of the gpio here too.
> >
> > No need to; the GPIO framework can handle this internally.
>
> Ahh, I said nothing :) so all my comments about that can be dropped.
>
> > > > + usleep_range(1500, 1800);
> > > > +
> > > > + return 0;
> > > > +
> > > > +disable_clk:
> > > > + gpiod_set_value_cansleep(ov8856->reset_gpio, 1);
> > >
> > > And here.. pls check the whole patch.
> > >
> > > > + clk_disable_unprepare(ov8856->xvclk);
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static void __ov8856_power_off(struct ov8856 *ov8856)
> > > > +{
> > > > + gpiod_set_value_cansleep(ov8856->reset_gpio, 1);
> > > > + regulator_bulk_disable(ARRAY_SIZE(ov8856_supply_names),
> > > > + ov8856->supplies);
> > > > + clk_disable_unprepare(ov8856->xvclk);
> > >
> > > Clk is only availabel in DT use-case.
> > >
> > > > +}
> > > > +
> > > > static int __maybe_unused ov8856_suspend(struct device *dev)
> > > > {
> > > > struct i2c_client *client = to_i2c_client(dev);
> > > > @@ -918,6 +978,7 @@ static int __maybe_unused ov8856_suspend(struct device *dev)
> > > > if (ov8856->streaming)
> > > > ov8856_stop_streaming(ov8856);
> > > >
> > > > + __ov8856_power_off(ov8856);
> > > > mutex_unlock(&ov8856->mutex);
> > > >
> > > > return 0;
> > > > @@ -931,6 +992,8 @@ static int __maybe_unused ov8856_resume(struct device *dev)
> > > > int ret;
> > > >
> > > > mutex_lock(&ov8856->mutex);
> > > > +
> > > > + __ov8856_power_on(ov8856);
> > > > if (ov8856->streaming) {
> > > > ret = ov8856_start_streaming(ov8856);
> > > > if (ret) {
> > > > @@ -1092,29 +1155,54 @@ static int ov8856_identify_module(struct ov8856 *ov8856)
> > > > return 0;
> > > > }
> > > >
> > > > -static int ov8856_check_hwcfg(struct device *dev)
> > > > +static int ov8856_get_hwcfg(struct ov8856 *ov8856)
> > > > {
> > > > + struct device *dev = ov8856->dev;
> > > > struct fwnode_handle *ep;
> > > > struct fwnode_handle *fwnode = dev_fwnode(dev);
> > > > struct v4l2_fwnode_endpoint bus_cfg = {
> > > > .bus_type = V4L2_MBUS_CSI2_DPHY
> > > > };
> > > > - u32 mclk;
> > > > + u32 xvclk_rate;
> > > > int ret;
> > > > unsigned int i, j;
> > > >
> > > > if (!fwnode)
> > > > return -ENXIO;
> > > >
> > > > - ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk);
> > > > + ret = fwnode_property_read_u32(fwnode, "clock-frequency",
> > > > + &xvclk_rate);
> > > > if (ret)
> > > > return ret;
> > > >
> > > > - if (mclk != OV8856_MCLK) {
> > > > - dev_err(dev, "external clock %d is not supported", mclk);
> > > > - return -EINVAL;
> > > > + if (!is_acpi_node(fwnode)) {
> > > > + ov8856->xvclk = devm_clk_get(dev, "xvclk");
> > > > + if (IS_ERR(ov8856->xvclk)) {
> > > > + dev_err(dev, "could not get xvclk clock (%pe)\n",
> > > > + ov8856->xvclk);
> > > > + return PTR_ERR(ov8856->xvclk);
> > > > + }
> > > > +
> > > > + clk_set_rate(ov8856->xvclk, xvclk_rate);
> > > > + xvclk_rate = clk_get_rate(ov8856->xvclk);
> > > > }
> > >
> > > Why do we handle the clock only in DT case? Is there a problem with the
> > > clock handling and ACPI?
> >
> > Not really, it's just that ACPI does not provide an interface to the clocks
> > as such.
>
> But you will get a clk by devm_clk_get()?
No, because ACPI does not expose one to drivers. Effectively the entire
power sequences are implemented in ACPI, not in the driver.
--
Regards,
Sakari Ailus
