Introduce a new pad operation to allow retrieving the media bus
configuration on a subdevice pad.
The newly introduced operation reassembles the s/g_mbus_config video
operation, which have been on their way to be deprecated since a long
time.
Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
include/media/v4l2-subdev.h | 69 +++++++++++++++++++++++++++++++++++++
1 file changed, 69 insertions(+)
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index a4848de59852..fc16af578471 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -350,6 +350,71 @@ struct v4l2_mbus_frame_desc {
unsigned short num_entries;
};
+/**
+ * struct v4l2_mbus_parallel_config - parallel mbus configuration
+ * @hsync_active: hsync active state: 1 for high, 0 for low
+ * @vsync_active: vsync active state: 1 for high, 0 for low
+ * @pclk_rising: pixel clock active edge: 1 for rising, 0 for falling
+ * @data_active: data lines active state: 1 for high, 0 for low
+ */
+struct v4l2_mbus_parallel_config {
+ unsigned int hsync_active : 1;
+ unsigned int vsync_active : 1;
+ unsigned int pclk_rising : 1;
+ unsigned int data_active : 1;
+};
+
+/**
+ * struct v4l2_mbus_csi2_dphy_config - MIPI CSI-2 DPHY mbus configuration
+ * @data_lanes: number of data lanes in use
+ * @clock_noncontinuous: non continuous clock enable flag: 1 for non
+ * continuous clock, 0 for continuous clock.
+ */
+struct v4l2_mbus_csi2_dphy_config {
+ unsigned int data_lanes : 3;
+ unsigned int clock_noncontinuous : 1;
+};
+
+/**
+ * struct v4l2_mbus_csi2_cphy_config - MIPI CSI-2 CPHY mbus configuration
+ *
+ * TODO
+ */
+struct v4l2_mbus_csi2_cphy_config {
+ /* TODO */
+};
+
+/**
+ * struct v4l2_mbus_pad_config - media bus configuration
+ *
+ * Report the subdevice media bus information to inform the caller of the
+ * current bus configuration. The structure describes bus configuration
+ * parameters that might change in-between streaming sessions, in order to allow
+ * the caller to adjust its media bus configuration to match what is reported
+ * here.
+ *
+ * TODO: add '_pad_' to the name to distinguish this from the structure
+ * defined in v4l2_mediabus.h used for the same purpose by the g/s_mbus_config
+ * video operations. Reuse the there defined enum v4l2_mbus_type to define
+ * the bus type.
+ *
+ * @type: mbus type. See &enum v4l2_mbus_type
+ * @parallel: parallel bus configuration parameters.
+ * See &struct v4l2_mbus_parallel_config
+ * @csi2_dphy: MIPI CSI-2 DPHY configuration parameters
+ * See &struct v4l2_mbus_csi2_dphy_config
+ * @csi2_cphy: MIPI CSI-2 CPHY configuration parameters
+ * See &struct v4l2_mbus_csi2_cphy_config
+ */
+struct v4l2_mbus_pad_config {
+ enum v4l2_mbus_type type;
+ union {
+ struct v4l2_mbus_parallel_config parallel;
+ struct v4l2_mbus_csi2_dphy_config csi2_dphy;
+ struct v4l2_mbus_csi2_cphy_config csi2_cphy;
+ };
+};
+
/**
* struct v4l2_subdev_video_ops - Callbacks used when v4l device was opened
* in video mode.
@@ -670,6 +735,8 @@ struct v4l2_subdev_pad_config {
*
* @set_frame_desc: set the low level media bus frame parameters, @fd array
* may be adjusted by the subdev driver to device capabilities.
+ *
+ * @get_mbus_config: get the current mbus configuration
*/
struct v4l2_subdev_pad_ops {
int (*init_cfg)(struct v4l2_subdev *sd,
@@ -710,6 +777,8 @@ struct v4l2_subdev_pad_ops {
struct v4l2_mbus_frame_desc *fd);
int (*set_frame_desc)(struct v4l2_subdev *sd, unsigned int pad,
struct v4l2_mbus_frame_desc *fd);
+ int (*get_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+ struct v4l2_mbus_pad_config *config);
};
/**
--
2.26.0
