To make csi2_wait_for_phy() more readable, move code to separate
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
---
drivers/media/platform/ti-vpe/cal.c | 38 ++++++++++++++++++++---------
1 file changed, 26 insertions(+), 12 deletions(-)
diff --git a/drivers/media/platform/ti-vpe/cal.c b/drivers/media/platform/ti-vpe/cal.c
index 64ea92dbfac5..319312770eea 100644
--- a/drivers/media/platform/ti-vpe/cal.c
+++ b/drivers/media/platform/ti-vpe/cal.c
@@ -822,20 +822,10 @@ static void csi2_phy_init(struct cal_ctx *ctx)
csi2_cio_pwr(ctx, true);
}
-static void csi2_wait_for_phy(struct cal_ctx *ctx)
+static void csi2_wait_complexio_reset(struct cal_ctx *ctx)
{
int i;
- /* Steps
- * 2. Wait for completion of reset
- * Note if the external sensor is not sending byte clock,
- * the reset will timeout
- * 4.Force FORCERXMODE
- * G. Wait for all enabled lane to reach stop state
- * H. Disable pull down using pad control
- */
-
- /* 2. Wait for reset completion */
for (i = 0; i < 250; i++) {
if (reg_read_field(ctx->dev,
CAL_CSI2_COMPLEXIO_CFG(ctx->csi2_port),
@@ -854,7 +844,12 @@ static void csi2_wait_for_phy(struct cal_ctx *ctx)
CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED)
ctx_err(ctx, "Timeout waiting for Complex IO reset done\n");
- /* 4. G. Wait for all enabled lane to reach stop state */
+}
+
+static void csi2_wait_stop_state(struct cal_ctx *ctx)
+{
+ int i;
+
for (i = 0; i < 10; i++) {
if (reg_read_field(ctx->dev,
CAL_CSI2_TIMING(ctx->csi2_port),
@@ -866,9 +861,28 @@ static void csi2_wait_for_phy(struct cal_ctx *ctx)
ctx->csi2_port,
reg_read(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port)),
(i >= 10) ? "(timeout)" : "");
+
if (reg_read_field(ctx->dev, CAL_CSI2_TIMING(ctx->csi2_port),
CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK) != 0)
ctx_err(ctx, "Timeout waiting for stop state\n");
+}
+
+static void csi2_wait_for_phy(struct cal_ctx *ctx)
+{
+ /* Steps
+ * 2. Wait for completion of reset
+ * Note if the external sensor is not sending byte clock,
+ * the reset will timeout
+ * 4.Force FORCERXMODE
+ * G. Wait for all enabled lane to reach stop state
+ * H. Disable pull down using pad control
+ */
+
+ /* 2. Wait for reset completion */
+ csi2_wait_complexio_reset(ctx);
+
+ /* 4. G. Wait for all enabled lane to reach stop state */
+ csi2_wait_stop_state(ctx);
ctx_dbg(1, ctx, "CSI2_%d_REG1 = 0x%08x (Bit(31,28) should be set!)\n",
(ctx->csi2_port - 1), reg_read(ctx->cc, CAL_CSI2_PHY_REG1));
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
