Mauro,
I had to make 2 changes to get the patch to work for me
see below
HTH
-Rob
> Robert Lowery wrote:
>> Mauro's new code does the 500000 offset unconditionally for DTV7 by
>> setting offset = 2250000, not just when the ZARLINK456 or DIBCOM52
>> tables
>> were explicitly selected. This change is what appears to cause issues
>> for
>> me.
>
> I've reviewed all information and troubles we have with xc3028 tuning,
> including the reports related to newer firmwares for XC3028L. I think
> that the right fix is the one provided on this patch.
>
> Could you all please verify if this patch fixes the issues, without
> causing
> any regression?
>
> Cheers,
> Mauro.
>
> ---
>
> V4L/DVB: tuner-xc2028: fix tuning logic
>
> There's one reported regression in Australia (DTV7) and some
> reported troubles with newer firmwares. Rework the logic to improve
> tuner on those cases.
>
> Thanks-to: Robert Lowery <rglowery@xxxxxxxxxxxxxx>
> Thanks-to: Stefan Ringel <stefan.ringel@xxxxxxxx>
> Signed-off-by: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
> ---
> drivers/media/common/tuners/tuner-xc2028.c | 51
> ++++++++++++++++++++--------
> 1 files changed, 37 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/media/common/tuners/tuner-xc2028.c
> b/drivers/media/common/tuners/tuner-xc2028.c
> index ed50168..eb782a0 100644
> --- a/drivers/media/common/tuners/tuner-xc2028.c
> +++ b/drivers/media/common/tuners/tuner-xc2028.c
> @@ -932,30 +932,49 @@ static int generic_set_freq(struct dvb_frontend *fe,
> u32 freq /* in HZ */,
> * that xc2028 will be in a safe state.
> * Maybe this might also be needed for DTV.
> */
> - if (new_mode == T_ANALOG_TV)
> + if (new_mode == T_ANALOG_TV) {
> rc = send_seq(priv, {0x00, 0x00});
>
> - /*
> - * Digital modes require an offset to adjust to the
> - * proper frequency.
> - * Analog modes require offset = 0
> - */
> - if (new_mode == T_DIGITAL_TV) {
> - /* Sets the offset according with firmware */
> + /* Analog modes require offset = 0 */
> + } else {
> + /*
> + * Digital modes require an offset to adjust to the
> + * proper frequency. The offset depends on what
> + * firmware version is used.
> + */
> +
> + /*
> + * Adjust to the center frequency. This is calculated by the
> + * formula: offset = 1.25MHz - BW/2
> + * For DTV 7/8, the firmware uses BW = 8000, so it needs a
> + * further adjustment to get the frequency center on VHF
> + */
> if (priv->cur_fw.type & DTV6)
> offset = 1750000;
> else if (priv->cur_fw.type & DTV7)
> offset = 2250000;
> else /* DTV8 or DTV78 */
> offset = 2750000;
> + if ((priv->cur_fw.type & DTV78) && freq < 470000000)
> + offset -= 500000;
>
> /*
> - * We must adjust the offset by 500kHz when
> - * tuning a 7MHz VHF channel with DTV78 firmware
> - * (used in Australia, Italy and Germany)
> + * xc3028 additional "magic"
> + * Depending on the firmware version, it needs some adjustments
> + * to properly centralize the frequency. This seems to be
> + * needed to compensate the SCODE table adjustments made by
> + * newer firmwares
> */
> - if ((priv->cur_fw.type & DTV78) && freq < 470000000)
> - offset -= 500000;
> +
> + if (priv->firm_version >= 0x0302) {
> + if (priv->cur_fw.type & DTV7)
> + offset -= 300000;
> + else if (type != ATSC) /* DVB @6MHz, DTV 8 and DTV 7/8 */
> + offset += 200000;
> + } else {
> + if (priv->cur_fw.type & DTV7)
> + offset -= 500000;
This should be offset += 500000;
> + }
> }
>
> div = (freq - offset + DIV / 2) / DIV;
> @@ -1114,7 +1133,11 @@ static int xc2028_set_params(struct dvb_frontend
> *fe,
>
> /* All S-code tables need a 200kHz shift */
> if (priv->ctrl.demod) {
> - demod = priv->ctrl.demod + 200;
> + /*
> + * Newer firmwares require a 200 kHz offset only for ATSC
> + */
> + if (type == ATSC || priv->firm_version < 0x0302)
> + demod = priv->ctrl.demod + 200;
> /*
> * The DTV7 S-code table needs a 700 kHz shift.
> * Thanks to Terry Wu <terrywu2009@xxxxxxxxx> for reporting this
I had to also delete the
if (type & DTV7)
demod += 500
I suspect this is no longer required due to the offset += 500000 above
> --
> 1.6.6.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
