Re: [V6, 2/2] media: i2c: ov02a10: Add OV02A10 image sensor driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Dongchun,

On Wed, Dec 11, 2019 at 07:28:49PM +0800, Dongchun Zhu wrote:
> Add a V4L2 sub-device driver for OV02A10 image sensor. The OV02A10 is a
> 1/5" CMOS sensor from Omnivision, asupporting output format: 10-bit Raw.
> 
> This chip has a single MIPI lane interface and use the I2C bus for
> control and the CSI-2 bus for data.
> 
> Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
> ---
>  MAINTAINERS                 |    1 +
>  drivers/media/i2c/Kconfig   |   11 +
>  drivers/media/i2c/Makefile  |    1 +
>  drivers/media/i2c/ov02a10.c | 1102 +++++++++++++++++++++++++++++++++++++++++++
>  4 files changed, 1115 insertions(+)
>  create mode 100644 drivers/media/i2c/ov02a10.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 92a868c..e294530 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12135,6 +12135,7 @@ M:	Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
>  L:	linux-media@xxxxxxxxxxxxxxx
>  T:	git git://linuxtv.org/media_tree.git
>  S:	Maintained
> +F:	drivers/media/i2c/ov02a10.c
>  F:	Documentation/devicetree/bindings/media/i2c/ov02a10.txt
>  
>  OMNIVISION OV2680 SENSOR DRIVER
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index c68e002..d3e8c41 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -640,6 +640,17 @@ config VIDEO_IMX355
>  	  To compile this driver as a module, choose M here: the
>  	  module will be called imx355.
>  
> +config VIDEO_OV02A10
> +	tristate "OmniVision OV02A10 sensor support"
> +	depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
> +	select V4L2_FWNODE
> +	help
> +	  This is a Video4Linux2 sensor driver for the OmniVision
> +	  OV02A10 camera.
> +
> +	  To compile this driver as a module, choose M here: the
> +	  module will be called ov02a10.
> +
>  config VIDEO_OV2640
>  	tristate "OmniVision OV2640 sensor support"
>  	depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index c147bb9..b3769d7 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -63,6 +63,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
>  obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
>  obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
>  obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
> +obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
>  obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
>  obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
>  obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
> diff --git a/drivers/media/i2c/ov02a10.c b/drivers/media/i2c/ov02a10.c
> new file mode 100644
> index 0000000..0b930f6
> --- /dev/null
> +++ b/drivers/media/i2c/ov02a10.c
> @@ -0,0 +1,1102 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (c) 2019 MediaTek Inc.
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +#include <media/media-entity.h>
> +#include <media/v4l2-async.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-subdev.h>
> +#include <media/v4l2-fwnode.h>
> +
> +#define CHIP_ID						0x2509
> +#define OV02A10_REG_CHIP_ID_H				0x02
> +#define OV02A10_REG_CHIP_ID_L				0x03
> +#define OV02A10_ID(_msb, _lsb)				((_msb) << 8 | (_lsb))
> +
> +/* Bit[1] vertical upside down */
> +/* Bit[0] horizontal mirror */
> +#define REG_MIRROR_FLIP_CONTROL				0x3f
> +
> +/* Orientation */
> +#define REG_MIRROR_FLIP_ENABLE				0x03
> +
> +/* Bit[7] clock HS mode enable
> + * 0: Clock continue
> + * 1: Clock HS
> + * Bit[6:2] HS VOD adjust
> + * Bit[1:0] P VHI adjust
> + */
> +#define REG_HS_MODE_BLC					0x9d
> +
> +#define CLOCK_HS_MODE_ENABLE				BIT(7)
> +
> +/* Bit[2:0] MIPI transmission speed select */
> +#define TX_SPEED_AREA_SEL				0xa1
> +
> +#define REG_PAGE_SWITCH					0xfd
> +#define REG_GLOBAL_EFFECTIVE				0x01
> +#define REG_ENABLE					BIT(0)
> +#define OV02A10_MASK_8_BITS				0xff
> +
> +#define REG_SC_CTRL_MODE				0xac
> +#define SC_CTRL_MODE_STANDBY				0x00
> +#define SC_CTRL_MODE_STREAMING				0x01
> +
> +#define OV02A10_EXP_SHIFT				8
> +#define OV02A10_REG_EXPOSURE_H				0x03
> +#define OV02A10_REG_EXPOSURE_L				0x04
> +#define	OV02A10_EXPOSURE_MIN				4
> +#define OV02A10_EXPOSURE_MAX_MARGIN			4
> +#define	OV02A10_EXPOSURE_STEP				1
> +
> +#define OV02A10_VTS_SHIFT				8
> +#define OV02A10_REG_VTS_H				0x05
> +#define OV02A10_REG_VTS_L				0x06
> +#define OV02A10_VTS_MAX					0x209f
> +#define OV02A10_VTS_MIN					0x04cf
> +#define OV02A10_BASIC_LINE				1224
> +
> +#define OV02A10_REG_GAIN				0x24
> +#define OV02A10_GAIN_MIN				0x10
> +#define OV02A10_GAIN_MAX				0xf8
> +#define OV02A10_GAIN_STEP				0x01
> +#define OV02A10_GAIN_DEFAULT				0x40
> +
> +/* Test pattern control */
> +#define OV02A10_REG_TEST_PATTERN			0xb6
> +#define OV02A10_TEST_PATTERN_ENABLE			BIT(0)
> +
> +#define HZ_PER_MHZ					1000000L
> +#define OV02A10_LINK_FREQ_390MHZ			(390 * HZ_PER_MHZ)
> +#define OV02A10_ECLK_FREQ				(24 * HZ_PER_MHZ)
> +#define OV02A10_DATA_LANES				1
> +#define OV02A10_BITS_PER_SAMPLE				10
> +
> +static const char * const ov02a10_supply_names[] = {
> +	"dovdd",	/* Digital I/O power */
> +	"avdd",		/* Analog power */
> +	"dvdd",		/* Digital core power */
> +};
> +
> +#define OV02A10_NUM_SUPPLIES ARRAY_SIZE(ov02a10_supply_names)
> +
> +struct ov02a10_reg {
> +	u8 addr;
> +	u8 val;
> +};
> +
> +struct ov02a10_reg_list {
> +	u32 num_of_regs;
> +	const struct ov02a10_reg *regs;
> +};
> +
> +struct ov02a10_mode {
> +	u32 width;
> +	u32 height;
> +	u32 exp_def;
> +	u32 hts_def;
> +	u32 vts_def;
> +	const struct ov02a10_reg_list reg_list;
> +};
> +
> +struct ov02a10 {
> +	u32			eclk_freq;
> +	u32                     mipi_clock_tx_speed;
> +
> +	struct clk		*eclk;
> +	struct gpio_desc	*pd_gpio;
> +	struct gpio_desc	*n_rst_gpio;
> +	struct regulator_bulk_data supplies[OV02A10_NUM_SUPPLIES];
> +
> +	bool			streaming;
> +	bool			upside_down;
> +	bool			mipi_clock_hs_mode_enable;
> +
> +	/*
> +	 * Serialize control access, get/set format, get selection
> +	 * and start streaming.
> +	 */
> +	struct mutex		mutex;
> +	struct v4l2_subdev	subdev;
> +	struct media_pad	pad;
> +	struct v4l2_ctrl	*anal_gain;
> +	struct v4l2_ctrl	*exposure;
> +	struct v4l2_ctrl	*hblank;
> +	struct v4l2_ctrl	*vblank;
> +	struct v4l2_ctrl	*test_pattern;
> +	struct v4l2_mbus_framefmt	fmt;
> +	struct v4l2_ctrl_handler ctrl_handler;
> +
> +	const struct ov02a10_mode *cur_mode;
> +};
> +
> +static inline struct ov02a10 *to_ov02a10(struct v4l2_subdev *sd)
> +{
> +	return container_of(sd, struct ov02a10, subdev);
> +}
> +
> +/*
> + * eclk 24Mhz
> + * pclk 39Mhz
> + * linelength 934(0x3a6)
> + * framelength 1390(0x56E)
> + * grabwindow_width 1600
> + * grabwindow_height 1200
> + * max_framerate 30fps
> + * mipi_datarate per lane 780Mbps
> + */
> +static const struct ov02a10_reg ov02a10_1600x1200_regs[] = {
> +	{0xfd, 0x01},
> +	{0xac, 0x00},
> +	{0xfd, 0x00},
> +	{0x2f, 0x29},
> +	{0x34, 0x00},
> +	{0x35, 0x21},
> +	{0x30, 0x15},
> +	{0x33, 0x01},
> +	{0xfd, 0x01},
> +	{0x44, 0x00},
> +	{0x2a, 0x4c},
> +	{0x2b, 0x1e},
> +	{0x2c, 0x60},
> +	{0x25, 0x11},
> +	{0x03, 0x01},
> +	{0x04, 0xae},
> +	{0x09, 0x00},
> +	{0x0a, 0x02},
> +	{0x06, 0xa6},
> +	{0x31, 0x00},
> +	{0x24, 0x40},
> +	{0x01, 0x01},
> +	{0xfb, 0x73},
> +	{0xfd, 0x01},
> +	{0x16, 0x04},
> +	{0x1c, 0x09},
> +	{0x21, 0x42},
> +	{0x12, 0x04},
> +	{0x13, 0x10},
> +	{0x11, 0x40},
> +	{0x33, 0x81},
> +	{0xd0, 0x00},
> +	{0xd1, 0x01},
> +	{0xd2, 0x00},
> +	{0x50, 0x10},
> +	{0x51, 0x23},
> +	{0x52, 0x20},
> +	{0x53, 0x10},
> +	{0x54, 0x02},
> +	{0x55, 0x20},
> +	{0x56, 0x02},
> +	{0x58, 0x48},
> +	{0x5d, 0x15},
> +	{0x5e, 0x05},
> +	{0x66, 0x66},
> +	{0x68, 0x68},
> +	{0x6b, 0x00},
> +	{0x6c, 0x00},
> +	{0x6f, 0x40},
> +	{0x70, 0x40},
> +	{0x71, 0x0a},
> +	{0x72, 0xf0},
> +	{0x73, 0x10},
> +	{0x75, 0x80},
> +	{0x76, 0x10},
> +	{0x84, 0x00},
> +	{0x85, 0x10},
> +	{0x86, 0x10},
> +	{0x87, 0x00},
> +	{0x8a, 0x22},
> +	{0x8b, 0x22},
> +	{0x19, 0xf1},
> +	{0x29, 0x01},
> +	{0xfd, 0x01},
> +	{0x9d, 0x16},
> +	{0xa0, 0x29},
> +	{0xa1, 0x03},
> +	{0xad, 0x62},
> +	{0xae, 0x00},
> +	{0xaf, 0x85},
> +	{0xb1, 0x01},
> +	{0x8e, 0x06},
> +	{0x8f, 0x40},
> +	{0x90, 0x04},
> +	{0x91, 0xb0},
> +	{0x45, 0x01},
> +	{0x46, 0x00},
> +	{0x47, 0x6c},
> +	{0x48, 0x03},
> +	{0x49, 0x8b},
> +	{0x4a, 0x00},
> +	{0x4b, 0x07},
> +	{0x4c, 0x04},
> +	{0x4d, 0xb7},
> +	{0xf0, 0x40},
> +	{0xf1, 0x40},
> +	{0xf2, 0x40},
> +	{0xf3, 0x40},
> +	{0x3f, 0x00},
> +	{0xfd, 0x01},
> +	{0x05, 0x00},
> +	{0x06, 0xa6},
> +	{0xfd, 0x01},
> +};
> +
> +static const char * const ov02a10_test_pattern_menu[] = {
> +	"Disabled",
> +	"Color Bar",
> +};
> +
> +static const s64 link_freq_menu_items[] = {
> +	OV02A10_LINK_FREQ_390MHZ,
> +};
> +
> +static u64 to_pixel_rate(u32 f_index)
> +{
> +	u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV02A10_DATA_LANES;
> +
> +	do_div(pixel_rate, OV02A10_BITS_PER_SAMPLE);
> +
> +	return pixel_rate;
> +}
> +
> +static const struct ov02a10_mode supported_modes[] = {
> +	{
> +		.width = 1600,
> +		.height = 1200,
> +		.exp_def = 0x01ae,
> +		.hts_def = 0x03a6,
> +		.vts_def = 0x056e,
> +		.reg_list = {
> +			.num_of_regs = ARRAY_SIZE(ov02a10_1600x1200_regs),
> +			.regs = ov02a10_1600x1200_regs,
> +		},
> +	},
> +};
> +
> +static int ov02a10_write_array(struct ov02a10 *ov02a10,
> +			       const struct ov02a10_reg_list *r_list)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	unsigned int i;
> +	int ret;
> +
> +	for (i = 0; i < r_list->num_of_regs; i++) {
> +		ret = i2c_smbus_write_byte_data(client, r_list->regs[i].addr,
> +						r_list->regs[i].val);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int ov02a10_read_smbus(struct ov02a10 *ov02a10, unsigned char reg,
> +			      unsigned char *val)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	ret = i2c_smbus_read_byte_data(client, reg);
> +
> +	if (ret < 0)
> +		return ret;
> +
> +	*val = (unsigned char)ret;
> +
> +	return 0;
> +}
> +
> +static int ov02a10_mod_reg(struct ov02a10 *ov02a10, u8 reg, u8 mask, u8 val)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	u8 readval;
> +	int ret;
> +
> +	ret = ov02a10_read_smbus(ov02a10, reg, &readval);
> +	if (ret)
> +		return ret;
> +
> +	val = (readval & ~mask) | (val & mask);
> +
> +	return i2c_smbus_write_byte_data(client, reg, val);
> +}
> +
> +static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
> +			     struct v4l2_mbus_framefmt *fmt)
> +{
> +	fmt->width = mode->width;
> +	fmt->height = mode->height;
> +	fmt->field = V4L2_FIELD_NONE;
> +}
> +
> +static int ov02a10_set_fmt(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   struct v4l2_subdev_format *fmt)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> +
> +	mutex_lock(&ov02a10->mutex);
> +
> +	if (ov02a10->streaming) {
> +		mutex_unlock(&ov02a10->mutex);
> +		return -EBUSY;
> +	}
> +
> +	/* Only one sensor mode supported */
> +	mbus_fmt->code = ov02a10->fmt.code;
> +	ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> +	ov02a10->fmt = fmt->format;
> +
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return 0;
> +}
> +
> +static int ov02a10_get_fmt(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   struct v4l2_subdev_format *fmt)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> +
> +	mutex_lock(&ov02a10->mutex);
> +
> +	fmt->format = ov02a10->fmt;
> +	mbus_fmt->code = ov02a10->fmt.code;
> +	ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> +
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return 0;
> +}
> +
> +static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
> +				  struct v4l2_subdev_pad_config *cfg,
> +				  struct v4l2_subdev_mbus_code_enum *code)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	if (code->index >= ARRAY_SIZE(supported_modes))
> +		return -EINVAL;
> +
> +	code->code = ov02a10->fmt.code;

Do you plan to have a different format as well as a different resolution
for each mode?

> +
> +	return 0;
> +}
> +
> +static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
> +				    struct v4l2_subdev_pad_config *cfg,
> +				    struct v4l2_subdev_frame_size_enum *fse)
> +{
> +	if (fse->index >= ARRAY_SIZE(supported_modes))
> +		return -EINVAL;
> +
> +	fse->min_width  = supported_modes[fse->index].width;
> +	fse->max_width  = supported_modes[fse->index].width;
> +	fse->max_height = supported_modes[fse->index].height;
> +	fse->min_height = supported_modes[fse->index].height;
> +
> +	return 0;
> +}
> +
> +static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	u16 id;
> +	u8 chip_id_h;
> +	u8 chip_id_l;
> +	int ret;
> +
> +	/* Check sensor revision */
> +	ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_H, &chip_id_h);
> +	if (ret)
> +		return ret;
> +
> +	ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_L, &chip_id_l);
> +	if (ret)
> +		return ret;
> +
> +	id = OV02A10_ID(chip_id_h, chip_id_l);
> +	if (id != CHIP_ID) {
> +		dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
> +		return -EINVAL;
> +	}
> +
> +	dev_dbg(&client->dev, "Detected OV%04X sensor\n", id);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused ov02a10_power_on(struct device *dev)
> +{
> +	struct i2c_client *client = to_i2c_client(dev);
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	int ret;
> +
> +	gpiod_set_value_cansleep(ov02a10->n_rst_gpio, 0);
> +	gpiod_set_value_cansleep(ov02a10->pd_gpio, 1);
> +
> +	ret = clk_prepare_enable(ov02a10->eclk);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to enable eclk\n");
> +		return ret;
> +	}
> +
> +	ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to enable regulators\n");
> +		goto disable_clk;
> +	}
> +	usleep_range(5000, 6000);
> +
> +	gpiod_set_value_cansleep(ov02a10->pd_gpio, 0);
> +	usleep_range(5000, 6000);
> +
> +	gpiod_set_value_cansleep(ov02a10->n_rst_gpio, 1);
> +	usleep_range(5000, 6000);
> +
> +	ret = ov02a10_check_sensor_id(ov02a10);
> +	if (ret)
> +		goto disable_regulator;
> +
> +	return 0;
> +
> +disable_regulator:
> +	regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> +disable_clk:
> +	clk_disable_unprepare(ov02a10->eclk);
> +
> +	return ret;
> +}
> +
> +static int __maybe_unused ov02a10_power_off(struct device *dev)
> +{
> +	struct i2c_client *client = to_i2c_client(dev);
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	gpiod_set_value_cansleep(ov02a10->n_rst_gpio, 0);
> +	clk_disable_unprepare(ov02a10->eclk);
> +	gpiod_set_value_cansleep(ov02a10->pd_gpio, 1);
> +	regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> +
> +	return 0;
> +}
> +
> +static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	const struct ov02a10_reg_list *reg_list;
> +	int ret;
> +
> +	/* Apply default values of current mode */
> +	reg_list = &ov02a10->cur_mode->reg_list;
> +	ret = ov02a10_write_array(ov02a10, reg_list);
> +	if (ret)
> +		return ret;
> +
> +	/* Apply customized values from user */
> +	ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
> +	if (ret)
> +		return ret;
> +
> +	/* Set orientation to 180 degree */
> +	if (ov02a10->upside_down) {
> +		ret = i2c_smbus_write_byte_data(client, REG_MIRROR_FLIP_CONTROL,
> +						REG_MIRROR_FLIP_ENABLE);
> +		if (ret) {
> +			dev_err(&client->dev, "failed to set orientation\n");
> +			return ret;
> +		}
> +		ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> +						REG_ENABLE);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	/* Set clock lane transmission mode according to DT property */
> +	ret = ov02a10_mod_reg(ov02a10, REG_HS_MODE_BLC, CLOCK_HS_MODE_ENABLE,
> +			      ov02a10->mipi_clock_hs_mode_enable ?
> +			      CLOCK_HS_MODE_ENABLE : 0);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Set mipi TX speed according to DT property */
> +	ret = i2c_smbus_write_byte_data(client, TX_SPEED_AREA_SEL,
> +					ov02a10->mipi_clock_tx_speed);
> +	if (ret < 0)
> +		return ret;
> +
> +	/* Set stream on register */
> +	return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
> +					 SC_CTRL_MODE_STREAMING);
> +}
> +
> +static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +
> +	return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
> +					 SC_CTRL_MODE_STANDBY);
> +}
> +
> +static int ov02a10_entity_init_cfg(struct v4l2_subdev *sd,
> +				   struct v4l2_subdev_pad_config *cfg)
> +{
> +	struct v4l2_subdev_format fmt = {
> +		.which = cfg ? V4L2_SUBDEV_FORMAT_TRY
> +			     : V4L2_SUBDEV_FORMAT_ACTIVE,
> +		.format = {
> +			.width = 1600,
> +			.height = 1200
> +		}
> +	};
> +
> +	ov02a10_set_fmt(sd, cfg, &fmt);
> +
> +	return 0;
> +}
> +
> +static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
> +{
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
> +	mutex_lock(&ov02a10->mutex);
> +
> +	if (ov02a10->streaming == on)
> +		goto unlock_and_return;
> +
> +	if (on) {
> +		ret = pm_runtime_get_sync(&client->dev);
> +		if (ret < 0) {
> +			pm_runtime_put_noidle(&client->dev);
> +			goto unlock_and_return;
> +		}
> +
> +		ret = __ov02a10_start_stream(ov02a10);
> +		if (ret) {
> +			__ov02a10_stop_stream(ov02a10);
> +			ov02a10->streaming = !on;
> +			goto err_rpm_put;
> +		}
> +	} else {
> +		__ov02a10_stop_stream(ov02a10);
> +		pm_runtime_put(&client->dev);
> +	}
> +
> +	ov02a10->streaming = on;
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return 0;
> +
> +err_rpm_put:
> +	pm_runtime_put(&client->dev);
> +unlock_and_return:
> +	mutex_unlock(&ov02a10->mutex);
> +
> +	return ret;
> +}
> +
> +static const struct dev_pm_ops ov02a10_pm_ops = {
> +	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> +				pm_runtime_force_resume)
> +	SET_RUNTIME_PM_OPS(ov02a10_power_off, ov02a10_power_on, NULL)
> +};
> +
> +/*
> + * ov02a10_set_exposure - Function called when setting exposure time
> + * @priv: Pointer to device structure
> + * @val: Variable for exposure time, in the unit of micro-second
> + *
> + * Set exposure time based on input value.
> + *
> + * Return: 0 on success
> + */
> +static int ov02a10_set_exposure(struct ov02a10 *ov02a10, int val)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_H,
> +					((val >> OV02A10_EXP_SHIFT) &
> +					OV02A10_MASK_8_BITS));
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_L,
> +					(val & OV02A10_MASK_8_BITS));
> +	if (ret < 0)
> +		return ret;
> +
> +	return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> +					 REG_ENABLE);
> +}
> +
> +static int ov02a10_set_gain(struct ov02a10 *ov02a10, int val)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, OV02A10_REG_GAIN,
> +					(val & OV02A10_MASK_8_BITS));
> +	if (ret < 0)
> +		return ret;
> +
> +	return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> +					 REG_ENABLE);
> +}
> +
> +static int ov02a10_set_vblank(struct ov02a10 *ov02a10, int val)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_H,
> +					(((val + ov02a10->cur_mode->height -
> +					OV02A10_BASIC_LINE) >>
> +					OV02A10_VTS_SHIFT) &
> +					OV02A10_MASK_8_BITS));
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_L,
> +					((val + ov02a10->cur_mode->height -
> +					OV02A10_BASIC_LINE) &
> +					OV02A10_MASK_8_BITS));
> +	if (ret < 0)
> +		return ret;
> +
> +	return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> +					 REG_ENABLE);
> +}
> +
> +static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, int pattern)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	int ret;
> +
> +	if (pattern)
> +		pattern = OV02A10_TEST_PATTERN_ENABLE;
> +
> +	ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, OV02A10_REG_TEST_PATTERN,
> +					pattern);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> +					REG_ENABLE);
> +	if (ret < 0)
> +		return ret;
> +
> +	return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
> +					 SC_CTRL_MODE_STREAMING);
> +}
> +
> +static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> +	struct ov02a10 *ov02a10 = container_of(ctrl->handler,
> +					       struct ov02a10, ctrl_handler);
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	s64 max_expo;
> +	int ret;
> +
> +	/* Propagate change of current control to all related controls */
> +	if (ctrl->id == V4L2_CID_VBLANK) {
> +		/* Update max exposure while meeting expected vblanking */
> +		max_expo = ov02a10->cur_mode->height + ctrl->val -
> +			   OV02A10_EXPOSURE_MAX_MARGIN;
> +		__v4l2_ctrl_modify_range(ov02a10->exposure,
> +					 ov02a10->exposure->minimum, max_expo,
> +					 ov02a10->exposure->step,
> +					 ov02a10->exposure->default_value);
> +	}
> +
> +	/* V4L2 controls values will be applied only when power is already up */
> +	if (!pm_runtime_get_if_in_use(&client->dev))
> +		return 0;
> +
> +	switch (ctrl->id) {
> +	case V4L2_CID_EXPOSURE:
> +		ret = ov02a10_set_exposure(ov02a10, ctrl->val);
> +		break;
> +	case V4L2_CID_ANALOGUE_GAIN:
> +		ret = ov02a10_set_gain(ov02a10, ctrl->val);
> +		break;
> +	case V4L2_CID_VBLANK:
> +		ret = ov02a10_set_vblank(ov02a10, ctrl->val);
> +		break;
> +	case V4L2_CID_TEST_PATTERN:
> +		ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
> +		break;
> +	default:
> +		ret = -EINVAL;
> +		break;
> +	};
> +
> +	pm_runtime_put(&client->dev);
> +
> +	return ret;
> +}
> +
> +static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
> +	.s_stream = ov02a10_s_stream,
> +};
> +
> +static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
> +	.init_cfg = ov02a10_entity_init_cfg,
> +	.enum_mbus_code = ov02a10_enum_mbus_code,
> +	.enum_frame_size = ov02a10_enum_frame_sizes,
> +	.get_fmt = ov02a10_get_fmt,
> +	.set_fmt = ov02a10_set_fmt,
> +};
> +
> +static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
> +	.video	= &ov02a10_video_ops,
> +	.pad	= &ov02a10_pad_ops,
> +};
> +
> +static const struct media_entity_operations ov02a10_subdev_entity_ops = {
> +	.link_validate = v4l2_subdev_link_validate,
> +};
> +
> +static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
> +	.s_ctrl = ov02a10_set_ctrl,
> +};
> +
> +static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
> +{
> +	struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> +	const struct ov02a10_mode *mode;
> +	struct v4l2_ctrl_handler *handler;
> +	struct v4l2_ctrl *ctrl;
> +	u64 exposure_max;
> +	u32 pixel_rate, h_blank;
> +	int ret;
> +
> +	handler = &ov02a10->ctrl_handler;
> +	mode = ov02a10->cur_mode;
> +	ret = v4l2_ctrl_handler_init(handler, 7);
> +	if (ret)
> +		return ret;
> +
> +	handler->lock = &ov02a10->mutex;
> +
> +	ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ, 0, 0,
> +				      link_freq_menu_items);
> +	if (ctrl)
> +		ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +
> +	pixel_rate = to_pixel_rate(0);
> +	v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, 0, pixel_rate, 1,
> +			  pixel_rate);
> +
> +	h_blank = mode->hts_def - mode->width;
> +	ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
> +					    h_blank, h_blank, 1, h_blank);
> +	if (ov02a10->hblank)
> +		ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> +
> +	ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> +					    V4L2_CID_VBLANK, mode->vts_def -
> +					    mode->height,
> +					    OV02A10_VTS_MAX - mode->height, 1,
> +					    mode->vts_def - mode->height);
> +
> +	exposure_max = mode->vts_def - 4;
> +	ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> +					      V4L2_CID_EXPOSURE,
> +					      OV02A10_EXPOSURE_MIN,
> +					      exposure_max,
> +					      OV02A10_EXPOSURE_STEP,
> +					      mode->exp_def);
> +
> +	ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> +					       V4L2_CID_ANALOGUE_GAIN,
> +					       OV02A10_GAIN_MIN,
> +					       OV02A10_GAIN_MAX,
> +					       OV02A10_GAIN_STEP,
> +					       OV02A10_GAIN_DEFAULT);
> +
> +	ov02a10->test_pattern =
> +		v4l2_ctrl_new_std_menu_items(handler, &ov02a10_ctrl_ops,
> +					     V4L2_CID_TEST_PATTERN,
> +					     ARRAY_SIZE(ov02a10_test_pattern_menu) -
> +					     1, 0, 0,
> +					     ov02a10_test_pattern_menu);
> +
> +	if (handler->error) {
> +		ret = handler->error;
> +		dev_err(&client->dev, "failed to init controls(%d)\n", ret);
> +		goto err_free_handler;
> +	}
> +
> +	ov02a10->subdev.ctrl_handler = handler;
> +
> +	return 0;
> +
> +err_free_handler:
> +	v4l2_ctrl_handler_free(handler);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_check_hwcfg(struct device *dev, struct ov02a10 *ov02a10)
> +{
> +	struct fwnode_handle *ep;
> +	struct fwnode_handle *fwnode = dev_fwnode(dev);
> +	struct v4l2_fwnode_endpoint bus_cfg = {
> +		.bus_type = V4L2_MBUS_CSI2_DPHY
> +	};
> +	unsigned int i, j;
> +	int ret;
> +
> +	if (!fwnode)
> +		return -ENXIO;
> +
> +	ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
> +	if (!ep)
> +		return -ENXIO;
> +
> +	ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
> +	fwnode_handle_put(ep);
> +	if (ret)
> +		return ret;
> +
> +	/* Optional indication of mipi clock lane mode */
> +	if (bus_cfg.bus.mipi_csi2.flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK)
> +		ov02a10->mipi_clock_hs_mode_enable = true;
> +
> +	if (!bus_cfg.nr_of_link_frequencies) {
> +		dev_err(dev, "no link frequencies defined");
> +		ret = -EINVAL;
> +		goto check_hwcfg_error;
> +	}
> +
> +	for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
> +		for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
> +			if (link_freq_menu_items[i] ==
> +				bus_cfg.link_frequencies[j])
> +				break;
> +		}
> +
> +		if (j == bus_cfg.nr_of_link_frequencies) {
> +			dev_err(dev, "no link frequency %lld supported",
> +				link_freq_menu_items[i]);
> +			ret = -EINVAL;
> +			goto check_hwcfg_error;
> +		}
> +	}
> +
> +check_hwcfg_error:
> +	v4l2_fwnode_endpoint_free(&bus_cfg);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_probe(struct i2c_client *client)
> +{
> +	struct device *dev = &client->dev;
> +	struct ov02a10 *ov02a10;
> +	unsigned int rotation;
> +	unsigned int clock_lane_tx_speed;
> +	unsigned int i;
> +	int ret;
> +
> +	ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
> +	if (!ov02a10)
> +		return -ENOMEM;
> +
> +	ret = ov02a10_check_hwcfg(dev, ov02a10);
> +	if (ret) {
> +		dev_err(dev, "failed to check HW configuration: %d", ret);
> +		return ret;
> +	}
> +
> +	v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
> +	ov02a10->upside_down = false;
> +	ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
> +
> +	/* Optional indication of physical rotation of sensor */
> +	ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation", &rotation);
> +	if (!ret) {
> +		ov02a10->upside_down = rotation == 180;
> +		if (rotation == 180) {
> +			ov02a10->upside_down = true;
> +			ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> +		}
> +	} else {
> +		dev_warn(dev, "failed to get rotation\n");

The property is optional; you shouldn't warn it's missing in that case.

> +	}
> +
> +	/* Optional indication of mipi TX speed */
> +	ret = fwnode_property_read_u32(dev_fwnode(dev), "ovti,mipi-tx-speed",
> +				       &clock_lane_tx_speed);
> +

Please see my comments on v5.

> +	if (!ret)
> +		ov02a10->mipi_clock_tx_speed = clock_lane_tx_speed;
> +	else
> +		dev_warn(dev, "failed to get mipi tx speed, using default...\n");
> +
> +	/* Get system clock (eclk) */
> +	ov02a10->eclk = devm_clk_get(dev, "eclk");
> +	if (IS_ERR(ov02a10->eclk)) {
> +		ret = PTR_ERR(ov02a10->eclk);
> +		dev_err(dev, "failed to get eclk %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
> +				       &ov02a10->eclk_freq);
> +	if (ret) {
> +		dev_err(dev, "failed to get eclk frequency\n");
> +		return ret;
> +	}
> +
> +	ret = clk_set_rate(ov02a10->eclk, ov02a10->eclk_freq);
> +	if (ret) {
> +		dev_err(dev, "failed to set eclk frequency (24MHz)\n");
> +		return ret;
> +	}
> +
> +	if (clk_get_rate(ov02a10->eclk) != OV02A10_ECLK_FREQ) {
> +		dev_warn(dev, "wrong eclk frequency %d Hz, expected: %d Hz\n",
> +			 ov02a10->eclk_freq, OV02A10_ECLK_FREQ);
> +		return -EINVAL;
> +	}
> +
> +	ov02a10->pd_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_HIGH);
> +	if (IS_ERR(ov02a10->pd_gpio)) {
> +		ret = PTR_ERR(ov02a10->pd_gpio);
> +		dev_err(dev, "failed to get powerdown-gpios %d\n", ret);
> +		return ret;
> +	}
> +
> +	ov02a10->n_rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(ov02a10->n_rst_gpio)) {
> +		ret = PTR_ERR(ov02a10->n_rst_gpio);
> +		dev_err(dev, "failed to get reset-gpios %d\n", ret);
> +		return ret;
> +	}
> +
> +	for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
> +		ov02a10->supplies[i].supply = ov02a10_supply_names[i];
> +
> +	ret = devm_regulator_bulk_get(dev, OV02A10_NUM_SUPPLIES,
> +				      ov02a10->supplies);
> +	if (ret) {
> +		dev_err(dev, "failed to get regulators\n");
> +		return ret;
> +	}
> +
> +	mutex_init(&ov02a10->mutex);
> +	ov02a10->cur_mode = &supported_modes[0];
> +	ret = ov02a10_initialize_controls(ov02a10);
> +	if (ret) {
> +		dev_err(dev, "failed to initialize controls\n");
> +		goto err_destroy_mutex;
> +	}
> +
> +	ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +	ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
> +	ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> +	ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
> +	ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to init entity pads: %d", ret);
> +		goto err_free_handler;
> +	}
> +
> +	ret = v4l2_async_register_subdev(&ov02a10->subdev);
> +	if (ret) {
> +		dev_err(dev, "failed to register V4L2 subdev: %d", ret);
> +		goto err_clean_entity;
> +	}
> +
> +	pm_runtime_enable(dev);
> +	if (!pm_runtime_enabled(dev)) {
> +		ret = ov02a10_power_on(dev);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to power on: %d\n", ret);
> +			goto err_clean_entity;
> +		}
> +	}
> +
> +	return 0;
> +
> +err_clean_entity:
> +	media_entity_cleanup(&ov02a10->subdev.entity);
> +err_free_handler:
> +	v4l2_ctrl_handler_free(ov02a10->subdev.ctrl_handler);
> +err_destroy_mutex:
> +	mutex_destroy(&ov02a10->mutex);
> +
> +	return ret;
> +}
> +
> +static int ov02a10_remove(struct i2c_client *client)
> +{
> +	struct v4l2_subdev *sd = i2c_get_clientdata(client);
> +	struct ov02a10 *ov02a10 = to_ov02a10(sd);
> +
> +	v4l2_async_unregister_subdev(sd);
> +	media_entity_cleanup(&sd->entity);
> +	v4l2_ctrl_handler_free(sd->ctrl_handler);
> +	pm_runtime_disable(&client->dev);
> +	if (!pm_runtime_status_suspended(&client->dev))
> +		ov02a10_power_off(&client->dev);
> +	pm_runtime_set_suspended(&client->dev);
> +	mutex_destroy(&ov02a10->mutex);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id ov02a10_of_match[] = {
> +	{ .compatible = "ovti,ov02a10" },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, ov02a10_of_match);
> +
> +static struct i2c_driver ov02a10_i2c_driver = {
> +	.driver = {
> +		.name = "ov02a10",
> +		.pm = &ov02a10_pm_ops,
> +		.of_match_table = ov02a10_of_match,
> +	},
> +	.probe_new	= &ov02a10_probe,
> +	.remove		= &ov02a10_remove,
> +};
> +
> +module_i2c_driver(ov02a10_i2c_driver);
> +
> +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
> +MODULE_LICENSE("GPL v2");
> +

-- 
Regards,

Sakari Ailus



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux