On 2019-10-08 15:53, Tomasz Figa wrote:
> On Tue, Oct 8, 2019 at 10:35 PM Tomasz Figa <tfiga@xxxxxxxxxxxx> wrote:
>> On Tue, Oct 8, 2019 at 7:42 PM Tomasz Figa <tfiga@xxxxxxxxxxxx> wrote:
>>> On Tue, Oct 8, 2019 at 3:31 PM Jonas Karlman <jonas@xxxxxxxxx> wrote:
>>>> On 2019-10-08 07:27, Tomasz Figa wrote:
>>>>> Hi Ezequiel, Jonas,
>>>>>
>>>>> On Tue, Oct 8, 2019 at 2:46 AM Ezequiel Garcia <ezequiel@xxxxxxxxxxxxx> wrote:
>>>>>> From: Jonas Karlman <jonas@xxxxxxxxx>
>>>>>>
>>>>>> TRM specify supported image size 48x48 to 4096x2304 at step size 16 pixels,
>>>>>> change frmsize max_width/max_height to match TRM.
>>>>>>
>>>>>> Fixes: 760327930e10 ("media: hantro: Enable H264 decoding on rk3288")
>>>>>> Signed-off-by: Jonas Karlman <jonas@xxxxxxxxx>
>>>>>> ---
>>>>>> v2:
>>>>>> * No changes.
>>>>>>
>>>>>> drivers/staging/media/hantro/rk3288_vpu_hw.c | 4 ++--
>>>>>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/staging/media/hantro/rk3288_vpu_hw.c b/drivers/staging/media/hantro/rk3288_vpu_hw.c
>>>>>> index 6bfcc47d1e58..ebb017b8a334 100644
>>>>>> --- a/drivers/staging/media/hantro/rk3288_vpu_hw.c
>>>>>> +++ b/drivers/staging/media/hantro/rk3288_vpu_hw.c
>>>>>> @@ -67,10 +67,10 @@ static const struct hantro_fmt rk3288_vpu_dec_fmts[] = {
>>>>>> .max_depth = 2,
>>>>>> .frmsize = {
>>>>>> .min_width = 48,
>>>>>> - .max_width = 3840,
>>>>>> + .max_width = 4096,
>>>>>> .step_width = H264_MB_DIM,
>>>>>> .min_height = 48,
>>>>>> - .max_height = 2160,
>>>>>> + .max_height = 2304,
>>>>> This doesn't match the datasheet I have, which is RK3288 Datasheet Rev
>>>>> 1.4 and which has the values as in current code. What's the one you
>>>>> got the values from?
>>>> The RK3288 TRM vcodec chapter from [1], unknown revision and date, lists 48x48 to 4096x2304 step size 16 pixels under 25.5.1 H.264 decoder.
>>>>
>>>> I can also confirm that one of my test samples (PUPPIES BATH IN 4K) is 4096x2304 and can be decoded after this patch.
>>>> However the decoding speed is not optimal at 400Mhz, if I recall correctly you need to set the VPU1 clock to 600Mhz for 4K decoding on RK3288.
>>>>
>>>> I am not sure if I should include a v2 of this patch in my v2 series, as-is this patch do not apply on master (H264_MB_DIM has changed to MB_DIM in master).
>>>>
>>>> [1] http://www.t-firefly.com/download/firefly-rk3288/docs/TRM/rk3288-chapter-25-video-encoder-decoder-unit-(vcodec).pdf
>>> I checked the RK3288 TRM V1.1 too and it refers to 3840x2160@24fps as
>>> the maximum.
>>>
>>> As for performance, we've actually been getting around 33 fps at 400
>>> MHz with 3840x2160 on our devices (the old RK3288 Asus Chromebook
>>> Flip).
>>>
>>> I guess we might want to check that with Hantro.
>> Could you check the value of bits 10:0 in register at 0x0c8? That
>> should be the maximum supported stream width in the units of 16
>> pixels.
> Correction: The unit is 1 pixel and there are additional 2 most
> significant bits at 0x0d8, 15:14.
I will check this later tonight when I have access to my devices.
The PUPPIES BATH IN 4K (4096x2304) sample decoded without issue using rockchip 4.4 BSP kernel and mpp last time I tested.
The vcodec driver in 4.4 BSP kernel use 300/400 Mhz as default clock rate and will change to 600 Mhz when width is over 2560, see [1]:
raise frequency for resolution larger than 1440p avc
[1] https://github.com/rockchip-linux/kernel/blob/develop-4.4/drivers/video/rockchip/vcodec/vcodec_service.c#L2551-L2570
Regards,
Jonas
>
> Best regards,
> Tomasz
