On 9/3/19 6:49 PM, Jacopo Mondi wrote:
> Hi Sakari, Hans,
>
> On Tue, Sep 03, 2019 at 04:06:26PM +0300, Sakari Ailus wrote:
>> Hi Hans, Jacopo,
>>
>> On Thu, Aug 29, 2019 at 02:55:30PM +0200, Hans Verkuil wrote:
>>> On 8/29/19 2:40 PM, Jacopo Mondi wrote:
>>>> HI Hans,
>>>>
>>>> On Thu, Aug 29, 2019 at 12:20:18PM +0200, Hans Verkuil wrote:
>>>>> On 8/27/19 11:23 AM, Jacopo Mondi wrote:
>>>>>> Report the native pixel array size and the crop bounds for the ov5670
>>>>>> sensor driver.
>>>>>>
>>>>>> Signed-off-by: Jacopo Mondi <jacopo@xxxxxxxxxx>
>>>>>> ---
>>>>>> drivers/media/i2c/ov5670.c | 20 ++++++++++++++++++++
>>>>>> 1 file changed, 20 insertions(+)
>>>>>>
>>>>>> diff --git a/drivers/media/i2c/ov5670.c b/drivers/media/i2c/ov5670.c
>>>>>> index 2bc57e85f721..3e22fe9ccad1 100644
>>>>>> --- a/drivers/media/i2c/ov5670.c
>>>>>> +++ b/drivers/media/i2c/ov5670.c
>>>>>> @@ -2258,6 +2258,25 @@ static int ov5670_set_pad_format(struct v4l2_subdev *sd,
>>>>>> return 0;
>>>>>> }
>>>>>>
>>>>>> +static int ov5670_get_selection(struct v4l2_subdev *sd,
>>>>>> + struct v4l2_subdev_pad_config *cfg,
>>>>>> + struct v4l2_subdev_selection *sel)
>>>>>> +{
>>>>>> + switch (sel->target) {
>>>>>> + case V4L2_SEL_TGT_CROP_BOUNDS:
>>>>>> + case V4L2_SEL_TGT_NATIVE_SIZE:
>>>>>> + sel->r.left = 0;
>>>>>> + sel->r.top = 0;
>>>>>> + sel->r.width = 2592;
>>>>>> + sel->r.height = 1944;
>>>>>
>>>>> Why do you need this?
>>>>>
>>>>
>>>> I need to expose the pixel array size and the active pixel area size,
>>>> and I interpreted the two above targets as the right place where to do
>>>> so.
>>>
>>> That didn't answer my question :-)
>>>
>>> Why do you need to expose this? Who uses it for what purpose?
>>>
>>>>
>>>> At least for NATIVE_SIZE the documentation seems to match my
>>>> understanding:
>>>>
>>>> "The native size of the device, e.g. a sensor’s pixel array. left and top
>>>> fields are zero for this target."
>>>
>>> Correct.
>>>
>>>>
>>>>
>>>>> Since the format can change for this and the next driver I think CROP_BOUNDS
>>>>> at least should match the current format.
>>>>>
>>>>
>>>> Ah, does it? It was not clear to me from the documentation, as it
>>>> suggested to me that target actually identifies the active pixel area
>>>>
>>>> "Bounds of the crop rectangle. All valid crop rectangles fit inside the
>>>> crop bounds rectangle."
>>>>
>>>> It does not mention format, should this be updated?
>>>
>>> The problem is that for sensors it is indeed not clear.
>>>
>>> In principle the crop bounds matches the resolution that the sensor uses
>>> pre-scaling. So yes, that means that it is equal to the native size.
>>>
>>> But many sensors have a discrete list of supported formats and it is not
>>> clear how they map each format to the actual sensor. If it is clearly just
>>> done through binning or averaging, then all is fine.
>>
>> Sensor drivers do; sensors themselves support much, much more than most
>> drivers allow. But this is due to the nature of information available to
>> the sensor driver developers, not really something that is trivial to
>> change.
>>
>>>
>>> If the formats have different aspect ratios, then it becomes a bit more
>>> difficult how to relate the crop bounds with the format since you may not
>>> know to which sensor area the current format corresponds.
>>>
>>> I have no clear answer for you, to be honest, but it can get tricky.
>>
>> I've suggested earlier that the crop and compose selection targets to be
>> used to convey the cropping and binning (or scaling) that is done on the
>> sensor, in that order. In reality, there are usually more than one
>> (sometimes three) inside a sensor to crop, and often more than one place to
>> scale as well. So the driver would need to accommodate this.
>>
>> The modes come with both cropping and scaling configuration, and V4L2 only
>> allows specifying one at a time. In principle an output size may be
>> achieved by scaling and cropping by different amounts, and as most drivers
>> use only the output format (size) in mode selection, the result could be
>> ambiguous. In practice this hasn't been an actual issue.
>>
>> Better sensor drivers (such as smiapp) do not have this problem as the
>> configurations (cropping in three different places as well as binning and
>> scaling) can be all independently configured. So with some luck this
>> problem could disappear in time with newer hardware and better hardware
>> documentation.
>>
>> I have no objections to providing the cropping and scaling information to
>> the user space using the selection rectangles, albeit it's somewhat against
>> the semantics currently. This approach would also require using compose
>> rectangles on the source pads which is not supported (documentation-wise)
>> at the moment, but it's better that way: it can be added now. There are
>> other, older, drivers such as omap3isp that configure scaling based on the
>> source format configuration only.
>
> Thanks for all information here, but I think we've gone a bit far
> from my original point. The cropping and scaling informations you
> mention are, in my understanding, the portion of the pixel array which
> is fed to the ISP before scaling, and the result of the ISP
> binning/averaging respectively. Those information indeed depends on the
> desired capture resolution, the driver implementation, and the sensor
> capabilities.
>
> What I was interested in was just reporting to userspace the physical
> size of the active pixel array area, which should reasonably be
> defined as a sub-portion of the native pixel array, excluding the back
> calibration pixels.
>
> In one of the previous emails Hans suggested to use CROP_DEFAULT for
> that purpose, but in the documentation it is reported not to apply to
> subdevice :(
>
> Do we need a new target, similar to V4L2_SEL_TGT_NATIVE_SIZE that
> could maybe report multiple rectangles to accommodate cross-shaped
> sensors?
>
> Are the selection API the right place to report these information?
> With a control, it might be easier to report such a static
> information...
Sorry for the late follow-up.
I am uncomfortable with hacking something here. I strongly feel that we
are missing a proper API to configure a sensor.
If I look at video receivers (SDTV or HDTV), then in both cases you set up
the incoming video resolution with S_STD or S_DV_TIMINGS. This explicitly
defines the incoming image size and all crop/compose/scale operations
operate on that image size.
In my opinion we are missing an equivalent to that for sensors. I think the
original thinking was that sensors have a fixed pixel array, so there is
nothing to configure. But with cross-shaped sensors, binning/skipping,
sensors that just hide all the inner details and just report a set of
discrete framesizes, this is not actually trivial anymore.
And the odd thing is that our API does have discovery (at least to some
extent) of the various options through ENUM_FRAMESIZES, but does not let
you choose a specific variant. We abuse S_FMT for this, which is really
not the right ioctl to use since it defines what you want to receive in
memory after cropping/composing/scaling, not the initial image size before
all these operations take place.
Regarding binning and skipping: I never understood why this wasn't
configured using controls. Is there a reason why it was never implemented
like that?
If we had a Set Source Size operation (either a control, new ioctl or selection
target) then you can use that to select a specific source size based on what
ENUM_FRAMESIZES reports. Sensor drivers can choose to either enumerate
variants based on the cross-shape and binning/skipping, or just enumerate variants
based on the cross-shape and add binning/skipping controls to explicitly set
this up.
In any case, since you now know exactly which image size the sensor produces,
you can set up all the selection rectangles associated with that correctly.
Since I am not a sensor expert I no doubt missed things, but in my view we
really need to see a sensor not as a fixed array, but as something more akin
to video receiver, i.e. you need to explicitly configure the video source
before cropping/composing/scaling takes place.
So in the example of a cross-shaped sensor ENUM_FRAMESIZES would report
two sizes (landscape/portrait), binning/cropping controls (optional, this
might be implicit in the enumerated framesizes), and after configuring all
this using the new API 'Set Source Size' (or whatever it will be called) and
possible binning/skipping controls, the user can read various selection
targets to get all the needed information.
Any cropping/composing/scaling will be done based on the selected image size
+ binning/skipping.
Re binning/skipping: one other option is to add a flags field to v4l2_frmsizeenum
that reports if the reported size was achieved via binning and/or skipping.
You wouldn't need controls in that case.
Regards,
Hans
